Fisher & Paykel WODV230, WOSV230 Installation Manual
WALL OVEN
WODV20 & WOSV20
models
INSTALLATION GUIDE
US CA
591007C 07.18
1SAFETY AND WARNINGS
WARNING!
Electrical shock hazard
Before carrying out any work on the electrical section of the appliance,
it must be disconnected from the mains electricity supply.
Connection to a good ground wiring system is absolutely essential
and mandatory.
Alterations to the domestic wiring system must only be made by a
qualified electrician
Failure to follow this advice may result in electrical shock or death.
IMPORTANT SAFETY INSTRUCTIONS!
●
Save these instructions for the local inspectors use.
●
To avoid hazard, follow these instructions carefully before installing or using this appliance.
●
Please make this information available to the person installing the appliance - doing so
could reduce your installation costs.
●
This oven is to be installed and connected to the electricity supply only by an authorized
person.
●
If the installation requires alterations to the domestic electrical system, call a qualified
electrician. The electrician should also check that the socket cable section is suitable for the
electricity drawn by the oven.
●
The oven must be grounded.
●
Installation must comply with your local building and electricity regulations.
●
WARNING!
Fire Hazard
Do not use adapters, reducers, or branching devices to connect this
appliance to the mains power supply.
Failure to follow this advice may result in overheating, burning, or fire.
This appliance must be installed and connected to the mains power supply only by a
suitably qualified person according to these installation instructions and in compliance with
any applicable local building and electricity regulations. Failure to install the appliance
correctly could invalidate any warranty or liability claims.
●
If the power supply cable is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified person in order to avoid a hazard.
●
A circuit breaker is recommended.
●
Do not use adaptors, reducers or branching devices to connect the oven to the mains
electricity supply, as they can cause overheating and burning.
●
Make sure the cavity is completely sealed with no gaps. This is to ensure the oven cooling
WARNING!
system functions correctly.
●
The appliance must not be installed behind a decorative door in order to avoid overheating.
Cut Hazard
Take care – some edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Very Heavy
oven
409 lb
models
DOUBLE
186 kg
Do not attempt to lift this product unassisted.
Lifting unassisted may cause serious injury.
Electrical requirements
●
Connect oven with copper wire only.
●
Do not cut the conduit.
●
A U.L. listed conduit connector must be provided at the junction box.
●
Do not ground to a gas pipe.
●
Do not have a fuse in the grounding or neutral circuit.
●
Fuse both sides of the line.
●
A time delay fuse or circuit breaker is recommended. If using a time delay fuse, then fuse
both sides of the line.
●
Flexible armored cable from the appliance should be connected directly to the junction box.
●
Connect directly to the fused disconnect (or circuit breaker box) through flexible, armored
or non-metallic sheathed, copper cable (with grounding wire).
●
If codes permit and a separate grounding wire is used, it is recommended that a qualified
electrician determine that the grounding path and wire gauge are in accordance with local
oven
SINGLE
110 kg
242 lb
models
codes.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
2
2PARTS SUPPLIED
Screws
(2) for Single oven models
Long Trim (1)
(to be fitted in a flush installation)
(4) for Double oven models
Spacers
(2) for Single oven models
(4) for Double oven models
3PRIOR TO INSTALLATION
●
The countertop and oven cavity are square and level, and are the required dimensions.
●
The installation will comply with all clearance requirements and applicable standards and regulations.
●
The isolating switch will be easily accessible to the customer with the oven installed.
●
The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening.
●
The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
●
The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
●
The oven will rest on a surface that can support its weight.
●
The height from the floor suits the customer.
●
You consult local building authorities and by-laws if in doubt regarding installation.
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
4AFTER INSTALLATION
IMPORTANT!
Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without
obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
●
The oven door(s) can open fully without obstruction.
●
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage caused by this
removal.
●
The power supply cable does not touch any hot metal parts.
●
The isolating switch is easily accessible to the customer with the oven installed.
●
You complete the ‘Final checklist’ at the end of the installation.
●
If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorized Service Center, Customer Care, or contact us through
our local website listed on the cover of this document.
3
H
B
C
A
D
G
F
E
5PRODUCT DIMENSIONS - SINGLE OVENS
FRONT
PROFILE
PRODUCT DIMENSIONS
Overall height of product 27 1/8” (689)
A
Overall width of product 29 13/16” (757)
PLAN
4
B
Overall depth of product (excludes handle and dials) 23 15/16” (608)
C
Depth of oven front and control panel (excludes handle and dials) 1 9/16” (39)
D
Depth of chassis (does not include oven front) 22 3/8” (569)
E
Height of chassis 26 9/16” (675)
F
Depth of door (open) (measured from front of door) 20 7/8” (530)
G
Overall width of chassis 28 5/16” (720)
H
WOSV230
INCHES (MM)
Loading...