Fisher & Paykel OB60SCT, OB60SLC, OB60SCM, OB60S9D, OB60SDT Installation Manual
...
OB60 models
BUILT IN OVEN
INSTALLATION GUIDE
NZ AU GB IE
591785A / 1105822-ß002.19
1
1SAFETY AND WARNINGS
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country,
go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.
IMPORTANT SAFETY INSTRUCTIONS
To avoid hazard, follow these instructions carefully
before installing or using this appliance:
Make this information available to the person
installing the appliance–doing so could reduce your
installation costs.
This appliance must be installed and connected to
the mains power supply only by a suitably qualified
person according to these installation instructions
and in compliance with any applicable local building
and electricity regulations. Failure to install the
appliance correctly could invalidate any warranty or
liability claims.
If the power supply cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.
The appliance must not be installed behind a
decorative door in order to avoid overheating.
WARNING!
Electrical shock hazard
Always disconnect the appliance from the
mains power supply before carrying out any
maintenance or repairs.
Connection to a good earth wiring system
isessential and mandatory.
Alterations to the domestic wiring system
must only be made by a
qualified electrician.
Failure to follow this advice may result in
electrical shock or death.
WARNING!
Cut Hazard
Take care—panel edges are sharp.
Failure to use caution could result in
injuryor cuts.
WARNING!
Fire hazard
Do not use adapters, reducers, or branching
devices to connect this appliance to the
mains power supply.
Failure to follow this advice may result in
overheating, burning, or fire.
2
2PRIOR TO INSTALLATION
3DURING INSTALLATION
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation,
we recommend moisture-proofing the oven cavity.
Before you install the oven, make sure:
the benchtop and oven cavity are square and level, and are the required dimensions.
the installation will comply with all clearance requirements and applicable standards and regulations.
a suitable isolating switch providing full disconnection from the mains power supply (under overvoltage category III conditions) is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact
separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the requirements).
the isolating switch will be easily accessible to the customer with the oven installed.
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing.
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
the oven will rest on a surface that can support its weight
the height from the floor suits the customer.
you consult local building authorities and by-laws if in doubt regarding installation.
IMPORTANT!
Take extra care not to damage the lower trim of the oven during installation.
The trim is important for correct air circulation and allows the door to open and close without obstruction.
Themanufacturer does not accept any responsibility for damage resulting from incorrect installation.
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing difficult. Fisher & Paykel will not cover the costs of removing the oven, or
of damage caused by this removal.
Use the supplied screws to secure the oven to the cabinetry. Do not over-tighten the screws.
Make sure that the power supply cable will not touch any hot metal parts.
Make sure that the isolating switch will be easily accessible by the customer.
Do not stand on the door, or place heavy objects on it.
Do not lift the oven by the door handle.
When handling the oven, take care not to damage the door sensor lever (near the top right corner of the oven seal).
Use easy-to-clean finishes for the wall surfaces surrounding the oven, so that cooking fume staining resulting from using the oven is easy to remove.
3
4PRODUCT DIMENSIONS (OB60S, OB60N MODELS)
OB60S MODELS OB60N MODELS
PRODUCT DIMENSIONS (MM) (MM)
a
Overall height* of product 597 450**
b
Overall width of product 595 595
c
Overall depth of product (excluding handle and knobs) 565 554
d
Height of chassis 582 436
e
Width of chassis 556 536
f
Depth of chassis 545 534
G
Depth of oven frame and control panel (distance between front of chassis and front of oven door, excluding knobs) 20 20
H
Depth of oven door when fully open (measured from front of control panel) 435 289
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer ’s instructions.
*All height measurements include mounted feet.
** If fitting the lower trim extension kit, the overall height of product (A) increases by 25 mm (to 475 mm).
A
CF
B
E
G
H
D
FRONT TOP SIDE
Loading...