Fisher & Paykel KS9017MX1 Kit Application

Refrigerator Surround Kit

For Models E388, E450, E402B, E411T, E415H, E440T, E442B, E521T and E522B, RF610A, RF540A, RF201A

Kit Application

This kit is designed to be used with 1695mm to 1780mm

(66 3/4” to 70 1/8”) High cabinet models, incorporating the “B” series

onwards refrigerators with curved & at door styling.

Note: This kit can be used for combining any of the following

products, E388, E450, E402B, E411T, E415H, E440T, E442B, E521T,

E522B, RF610A, RF540A, RF201A

(Part number for each installation type on page 4)

To give the most integrated look, the kitchen cabinetry should be

ush with the front of the refrigerator door.

Tools Required

No. 2 square type drill bit - long

•

Electric drill

•

Flat blade screwdriver

•

1 x 16mm (11/16in) piece of MDF the same size as the base of

•

the cavity.

Joiner kit (part number 813690) required if joining two

•

refrigerators side by side.

Parts Included in Kit

Top Trim (1) Side Trim (2) Bottom Trim (1)

Top Trim Brackets

(2) Single Refrigerator Kits

(3) Two Refrigerator Kits

Side Trim Brackets (10)

Screw Type A:

#8x12 Square Drive CSK (26)

1

2

FISHER AND PAYKEL REFRIGERATOR SURROUND KIT

All Dimensions are quoted in millimetres & inches

Width of models mm - inch Width A Depth B* Height C Air Vent D

790 model 962 - 37 7/8” 700 - 27 9/16” 1806 - 71 1/8” 200 - 8”

900 model 1072 - 42 1/4” 700 - 27 9/16” 1891 - 74 1/2” 200 - 8”

635 model + 635 model 1467 - 57 49/64” 700 - 27 9/16” 1806 - 71 1/8” 200 - 8”

680 model + 680 model 1557 - 61 19/64” 700 - 27 9/16” 1806 - 71 1/8” 200 - 8”

790 model + 790 model 1777 - 70” 700 - 27 9/16” 1806 - 71 1/8” 200 - 8”

* Depth is a minimum requirement

Installation Procedure

Step 1

1 Check that the internal Cupboard Cavity dimensions are correct (see diagram 1).

2 Unpack the refrigerator and/or freezer cabinets f rom their separate delivery cartons (see individual cartons for unpacking procedures).

3 Ensure the oor and/or the cupboards are protected from damage during the unpacking and assembly of the cabinets.

4 Check the refrigerator and freezer doors are hinged on the desired side.

5 Check that the kit is complete (ref er to kit parts list on page 1).

Note 1: Due to the size of the refrigerat or cabinets, it is essential that assembly of the kit be undertaken with a minimum of two able-bodied persons.

Note 2: It is imp ortant to include adequate venting to the top of the cabinet to ensure the efcient operation of the refrigerator.

Diagram 1: Cutout Dimensions (ush to edge of door)

Cut out dimensions above are to be used as minimum dimensions.

Step 2

1 Locate the two/three top trim brackets.

2 For two refrigerator kits, one bracket is to be screwed in the top centre of the cabinet, secure the top bracket with two of the screws

(Type A, #8 x 12 SQ Drive CSK).

3 For all kits, the remaining two brackets are to be secured on either side, by two screws which are mounted from the side (see diagram 2).

4 Looking at the front of the product, place the top brackets on top of the cabinet.

5 Care must be taken to line up the top front edge of the brackets with the leading edge of the cabinet.

Diagram 2: Top Trim Brackets