Fisher & Paykel DD605HSS-88466A, DD605I-88469A, DD605IH-88470A, DD605SS-88465A, DS605FDSS-88475A Installation Guide

Importand

SAVE THESEINSTRUCTIONS

T,_emodels shown in this document may not be available in all markets and are subject to change at any time. For current details about modal and specilication availability in your country, please go to our
web.site www.lisherpaykel.com or contact your local Fisher & Paykel dealer.

SAFETYAND WARNINGS

Electrical hazard

Before installing the DishDrawer ®,remove the house fuse or open the circuit breaker.

[f permanently connecting the DishDrawer ®,be sure the power is isolated and the DishDrawer ®unplugged.

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current, This
appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug, The plug must be plugged into a n appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service

representative if you are in doubt as to whether the appliance is properly grounded.

Do not modify the power supply plug provided with the appliance - if it will not fit the outJet, have a proper outJet installed by a qualified electrician. Do not use an extension cord, adapter plug or
multiple outJet box.

Failure to do so may result in electrical shock or death.

Cut hazard

Take care - pane[ edges are sharp.

FaiJure to use caution couJd resuJt in injury or cuts.

Important safety precautionJ.

installation of this DishDrawer ®requires basic mechanical and electrical skills.
Be sure to leave these instructions with the Customer.

installation must comply with your local building and electricity regulations.

At the completion of the DishDrawer _installation, the installer must perform the
Final Check List.

Remove all packaging materials supplied with the DishDrawer ®.
This DishDrawer _is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibifity of the plum bar and
electrician to ensure that each installation complies with ell Codes and Regulations.
The DishDrawer ®MUST be installed to allow for future removal from the enclosure ff service is required.

The switched power outlet must be outside the DishDrawer ®cavity so that it isaccessible after installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the

power supply cord.

If the DishDrawer _ is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer_). Old hoses should not be

reused.
Failure to install the DishDrawer ®correctly could invafidate any warranty or liability claims.

If the product is installed in a motor vehicle, boat or similar mobile facilit}; you must bring the vehicle, boat
or mobile facifity containing the product to the service shop at your expense or pay the service technician's
travel to the location of the product.

PRODUCT D MENS ONS

J_)Stt lJ t/O_) iJo_ro;7_s _)r /lJd lV tJO_) ;_ii! ;_OS#SOt)l',

D

C

t

I
I

i

i

Product dimensions (inches (mm)) _ _ B-

A overall height _ of produ(t 16 ys"(409) 16 y8"(409) 161/8"(409)

B overall width of product 23 _6" (595) 23 _d' (595) 23 _o" (595)
C overall depth of prod uct (exchcurvature/handle) 22 _6" (570) 22 _6" (570) 22 _6" (570)_

D depth of drawer (open) (c,xcLcurvature/handle) 20 Y2"(520) 20 1/2"(520) 20 1/2"(520)
E height _÷of chassis 16 Ys"(409) 16 Yd' (409) 16 Ys"(409)
F depth of chassis 21 3A"(552) 21 3A" (552) 21%" (552)

G depth of drawer front pane[ (c,xcl, curvature/hand e) 11_6"(18) 11_6"(18) 11_6"(18)

H depth of curvature or handle 1 sA6"(30) _*e n/a

[ height of drawer front 151/2" (394) 151¼6" (398) 15 1X6" (398) mm

J height of venting area at base of prod uct ¼" (7) 3/s" (9) %" (9)

K height of installation tab slots (on top ofchass[9 ¼d' (2) ¼6" (2) ¼6" (2)

L heig ht_<oftop of drawer to top of chassis ¼"(7) xd' (2) n/a

-Pl Cb

\

Cabinetry dimensions (inches (ram)) _ _ _-

A inside height of cavity 16¼"(412) 16¼"(412) 16 ¼"(412)

B inside width of cavity 23 %" (600) 23 %" (600) 23 %" (60@

C inside depth of cavity (inside) 22 %" (580) 22 %" (580) 22 %" (580)

D clearance below benchtop Min. W'(3) _ Min, W'(3) _ Min. W'(3) _

Clearance is measured from the underside of benchtop to the chassis

Minimum clearances (inches(mm))

Chassis heights ndude tab sots _' Panelth ckness- 6" (18 "_m) :÷ Designer handle- _ %" (4I mrr/,, Cu'ved handle- 1 _id'(36 n, rr/)

No_e: for Prefin shed Hat door models, the height from the top of handle to the top of door - 2 _6" (595 ram)

5

7

W' (13 mm) -_

PARTSSUPPUED

@

Drain hose
support (1)

Ifthe Drain hose(s)supplied are not long enough to reachyour services,you must use a Drain HoseExtension Kit P/N 925798which will extend the drain hose(s)by 3.6m.The kit isavailable from the nearest Fisher&Paykel

Authorized ServiceAgent, orToll free 1.888.936.7872or www.flsherpaykekcom.

Drain hose Wireclip (2) Clamp (1) Phillips Washer(1) Moisture protection Edge Protector(1)
joiner (1) 16 mm tape (1) (if servicehole

screws(% pcTrtitionismetcT/)

CAVITY PREPARATION

lmportand

Besuretheedgesof theservicesholeare smoothorcovered.If theservicesholeisthrough ametal
partition theholemustbeprotectedwith theEdgeProtectorsupplied topreventdamageto the
powercordor hoses.

_F

These marks indicate mounting tab screw locations.

Note: Toalign drawer front to adjacent cabinetry, the product to countertop clearancecan
be increased to 1/8"(3 ram).

..)e

Preferredposition. If adequate clearance, services hole can be higher.
If hole is higher, ensure drain hose(s)are routed straight into the waste connection.

Water Connection

Recommended HOT(Maximum 140°F/60°C).
Supplied hoseto suit 3/8" (9 mm) male compression fitting.

Water Pressure Max Min
Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi)

Other models 1 MPa (145 psi) 0.03 MPa (4.3 psi)

Drains will need to be separated to satisfy kosher requirements. Wesuggest you confirm

acceptability with your local rabbi in respect to kosher installations.

.... I

max. o 1 1/2"(38 mm)

Note: Services can be located

• , _de of DishDrawer®"

max. 17 1¼6"

_(450 mm) i

Drain hose 79" 71 "

(2011 mm) (1794 mm)

Inlet hose 37" 53"

(1551 ram) (1344 mm)

Power cord 51" 28"

(935 mm) (719 mm)

Left hand

side

Right hand

side

Adjacentcabinetrymust not
extendabovecadty base

min. 7 z/8"

i(200 mm)

L_

L 110-120 VAC

max. 15 A