Fisher Paykel DD24STI9N Planning guide
DATUM : FRONT OF CARCASS
in
17 7/8"
2 9/16"
21 /4"
20 /4"
in
18"
2 5/8"
22 1/16"
1/16"
1/16"
1/2"
B
23 9/16"
C
21 3/4"
24" Single DishDrawer™ Panel Ready Tall
DATA SHEET
Model no:
DD24STI9_N
DD24SHTI9 _N
(refer page for metric measurements)
Product Dimensions
a Overall height* of DishDrawer™
B Overall width* of DishDrawer™
C Depth of DishDrawer™ chassis*
D Depth of drawer (open) (measured from front datum)*
* Does not include the custom drawer panel or handle to be manufactured
and fitted by cabinetmaker.
Note: Service outlet at rear extends both sides, hoses and cords can be routed
to either or both.
CLEARANCE :
CORNER CUPBOARD
DATUM : BOTTOM OF CARCASS
0 5 10 20
PLAN VIEW
23 9/16"
B
FRONT VIEW
inches
D
CLEARANCE :
CORNER CUPBOARD
A
17 7/8"
Minimum Clearances
Minimum inside height of cavity from bottom datum**
Minimum inside width of cavity
DATUM : FRONT OF CARCASS
C
D
Minimum inside depth of cavity from front datum
Minimum height of ventilation gap under custom drawer panel
with external venting kit installed
Minimum gap from top of custom drawer panel to bottom of
benchtop
Minimum clearance from a corner cupboard
** This Dishdrawer™ has also been designed to fit a 18 7/8" high cavity.
For full details please refer to the installation manual.
NOTE: If using External Venting Kit and venting into the toekick area, a
minimum toekick height of 4" is required to prevent pooling of condensation.
INDICATES CABINETRY / PRODUCT DATUM -------------------------
INDICATES CABINETRY CLEARANCES --------------------------------
PROFILE VIEW
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
in
17 1/16”
2 7/16”
- 24 /16"
5/8“
- 1/16”
1/16”
20lb
in
18 /4”
2 7/16”
- 24 /16"
5/8“
- 1/16”
1/16”
20lb
18” CAVITY HEIGHT
CUSTOM PANEL PREPARATION
24" Single DishDrawer™ Panel Ready Tall
Model no:
DD24STI9_N
DD24SHTI9_N
(refer page 4 for metric measurements)
B
C
A
D
a
ISO VIEW
PROFILE VIEW
Dimensions
a Minimum height of drawer panel*
B Width of drawer panel
C Depth of front panel
D Minimum height of ventilation gap below front panel
Maximum weight of each drawer panel (including handle)
* For 18” cavity height and 1/16” ventilation gap below drawer panel with
external venting kit installed.
Drawer panel may be extended upwards to fit taller cavity. See installation
instructions for full clearance details.
NOTE: If using External Venting Kit and venting into the toekick area, a
minimum toekick height of 4“ is required to prevent pooling of condensation.
ATTACH CAVITY BRACKET FOR
18 7⁄8” CAVITY HEIGHT
18 7/8” CAVITY HEIGHT
Dimensions
a Minimum height of drawer panel*
B Width of drawer panel
C Depth of front panel
D Minimum height of ventilation gap below front panel
B
A
C
D
Maximum weight of each drawer panel (including handle)
* For 18 7/8” cavity height and 1/16” ventilation gap below drawer panel with
external venting kit installed.
Drawer panel may be extended upwards to fit taller cavity. See installation
instructions for full clearance details.
NOTE: If using External Venting Kit and venting into the toekick area, a
minimum toekick height of 4“ is required to prevent pooling of condensation.
a
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
ISO VIEW
PROFILE VIEW
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
Loading...