Page 1
f
in
16 1/8"
2 9/16"
22 1/2"
21 /4"
20 /4"
5/8" - 1/16"
16 1/16"
min 1/16"
in
min 16 1/4"
2 5/8"
min 22 1/16"
1/2"
CLEARANCE :
CORNER CUPBOARD
B
23 9/16"
PLAN VIEW
D
21 3/4"
e
CLEARANCE :
CORNER CUPBOARD
DATUM : FRONT OF CARCASS
DATUM : FRONT OF CARCASS
e C
22 1/2"
24" Single DishDrawer™ Panel Ready
DATA SHEET
Model no:
DD24SI9_N
(refer page for metric measurements)
Dimensions
a Overall height of DishDrawer™
B Overall width of DishDrawer™
c Overall depth of DishDrawer™
(assuming front panel thickness of 11/16")
D Depth of chassis
E Maximum extension of drawer from drawer front (excluding
handle)
F Depth of front panel*
g Height of front panel (recommended for a 1/16" ventilation
gap below panel, if cavity height is 16 1/4")
h Height of ventilation gap below front panel
* Handle and custom drawer panel not included. To be supplied and fitted by
cabinetmaker.
Minimum Clearances
Height of cavity
Width of cavity
Depth of cavity
Minimum clearance from a corner cupboard
NOTE: If using External Venting Kit and venting into the toekick area, a
minimum toekick height of 4" is required to prevent pooling of condensation.
DATUM : BOTTOM OF PRODUCT
0 5 10 20
FRONT VIEW
inches
A
16 1/8"
Note: Service outlet at rear extends both sides, hoses and cords can be routed
to either or both.
g
h
PROFILE VIEW
INDICATES CABINETRY / PRODUCT DATUM -------------------------
INDICATES CABINETRY CLEARANCES --------------------------------
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
Page 2
CUSTOM PANEL PREPARATION
in
16 1/16”
2 7/16”
- 24 /16"
5/8“
- 1/16”
1/16”
20lb
24" Single DishDrawer™ Panel Ready
Model no:
DD24SI9_N
(refer page 4 for metric measurements)
Dimensions
a Minimum height of drawer panel*
B Width of drawer panel
C Depth of front panel
D Minimum height of ventilation gap below front panel
Maximum weight of each drawer panel (including handle)
* For 16 1/4” cavity height and 1/16” ventilation gap below drawer panel with
external venting kit installed.
B
A
Drawer panel may be extended upwards to fit taller cavity. See installation
instructions for full clearance details.
NOTE: If using External Venting Kit and venting into the toekick area, a
minimum toekick height of 4" is required to prevent pooling of condensation.
C
D
a
ISO VIEW PROFILE VIEW
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
Page 3
f
mm
410
599
571
55
527
16-20
408
min 2
mm
min 412
600
min 560
1
CLEARANCE :
CORNER CUPBOARD
B
599
PLAN VIEW
D
553
e
CLEARANCE :
CORNER CUPBOARD
DATUM : FRONT OF CARCASS
DATUM : FRONT OF CARCASS
e C
571
24" Single DishDrawer™ Panel Ready
DATA SHEET
Model no:
DD24SI9_N
(refer page 1 for imperial measurements)
Dimensions
a Overall height of DishDrawer™
B Overall width of DishDrawer™
c Overall depth of DishDrawer™
(assuming front panel thickness of 18mm)
D Depth of chassis
E Maximum extension of drawer from drawer front (excluding
handle)
F Depth of front panel*
g Height of front panel (recommended for a 2mm ventilation
gap below panel, if cavity height is 412mm)
h Height of ventilation gap below front panel
* Handle and custom drawer panel not included. To be supplied and fitted by
cabinetmaker.
Minimum Clearances
Height of cavity
Width of cavity
Depth of cavity
Minimum clearance from a corner cupboard
NOTE: If using External Venting Kit and venting into the toekick area,
a minimum toekick height of 100mm is required to prevent pooling of
condensation.
DATUM : BOTTOM OF PRODUCT
FRONT VIEW
0 100 200 400
millimetres
A
410
Note: Service outlet at rear extends both sides, hoses and cords can be routed
to either or both.
g
h
PROFILE VIEW
INDICATES CABINETRY / PRODUCT DATUM -------------------------
INDICATES CABINETRY CLEARANCES --------------------------------
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
Page 4
CUSTOM PANEL PREPARATION
mm
408
596 - 615
16 - 20
2
9 kg
24" Single DishDrawer™ Panel Ready
Model no:
DD24SI9_N
(refer page 2 for imperial measurements)
Dimensions
a Minimum height of drawer panel*
B Width of drawer panel
C Depth of front panel
D Minimum height of ventilation gap below front panel
Maximum weight of each drawer panel (including handle)
* For 412mm cavity height and 2mm ventilation gap below drawer panel with
external venting kit installed.
Drawer panel may be extended upwards to fit taller cavity. See installation
instructions for full clearance details.
B
A
NOTE: If using External Venting Kit and venting into the toekick area,
a minimum toekick height of 100mm is required to prevent pooling of
condensation.
C
D
a
ISO VIEW PROFILE VIEW
DATE: 28.05.2018
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16'').
Please read the installation manual for detailed information on installing the
product. For full installation instructions & specifications visit fisherpaykel.com
Loading...