Fisher & Paykel DD24DHTI6-88530A, DD24SHTI6-88523A Installation Guide

integrated panel preparation

DD2¢STIand DD24DTI modeJs

Mod@lcs DD24STIet DD24DTI

Safety and warnings

Cut Hazard
Take care - pane[ edges are sharp°

Failure to use caution could result in injury or cuts°

Read these instructions completely and careful_yo
Ensure the product Lsnot plugged in.

Installation of DishDrawer ®panels requires basic mechanical and electrical skills.
Installation must comply with your local building and electfidty regulations.
Failure to instal_ the DishDrawer pands correctly could in validate any warranty or #abi#ty

claims.

Double models

P_educt p_epa_atien

Single models

P_educt preparation

Panel Installation

Badge CUtoOUt,handle and panel b_acket

Securing the panel b_ackets

Reconnecting the wires and fittin 9 the
panels and a custom toe kick (double modellso_"fly

6
7
8

Important!

SAVE THESEINSTRUCTIONS

i.!ixj{,< £:>ckcusr/,x#8 8,7y _/_8 f'>r ci.!':£,7 r)# si£ 8!;ols_ s_orWdc_.,d p8c/£{c1£>.,

8v<_iistiiit/h: y_>i/rcois _t04pk_ssmvisit oi.!/'icx:Ni >'/d>siiu i/see, o: 18 _78{:/_{:ore/'
or {:o, _s{ /::>i/':io{8i 7s£8,"& i*:;//_d c88k*':

Product preparation

l_'_'_,_be l_s_;__, _,_nodes

(12 ram)

i hdghtof

toekick

The following calculations assume the top of the upper panel is aligned with the top of the
adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet:

width of ALL panels

Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.

door clearance panel width

heigh t of upper panel

standard height B upper panel

height

heigh t of lower panel

Measure C(door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.

C upper panel lower panel

Note: The'door extension' B allows for the top of the upper panel to be above the DishDrawer ®where required.

height height

(8n

Air gap

Product preparation

Toe kick preparation

heigh t of toe kick panel

Measure D {height from the top of adjacent cabinet door fronts to the floor) and write it in the first

box below, then complete the equation.

D B toe kite panel

(779 ram) (12 ram)

Toe kick options
The black prefinished toe kick panel is

supplied. This panel can also have a front panel

of your choice attached to it using screws or an
adhesive.

A toe kick panel of any material with thickness
3/8- 3_" (9 - 19 mm) can be screwed to the

plastic toe kick panel bracket (supplied).

heiqht

Integrated Panel material

max.

3/8- 1_6" (16 - 20 mm) panel thickness 2%"(67mm)
Adequately sealed to withstand moisture (122°F/50°C @80% RH)

Toe kick

pane,

screws(5)

_2s/8;'-5"

(67-127mm)

ket (2)

Panelpanel
screws(12)

Integrated rectangular badge (2)
(Satinchrome supplied)

Toekick panel
bracket (1)

--<..

Prefinished Toe kick panel (1)

Product preparation

oi

inp'_ii_tio/ dic:;c,,_c:;zJs t,r iii ss tmtio } o4 p,s s o 7£

The following calculations assume the top of the panel is aligned with the top of the adjacent
cabinetry.

width of the panel

Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.

A door clearance panel width

+

height of the panel

Measure B(door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.

B panel height

_lr gap

Note: when the top of the DishDrawer ®has to be lower than the adjacent cabinetry, the panel can be increased
in height.

Product preparation

D_shDrawer®i_near floor ...................level. _ ..............................

UsethiS diagram I'f' -..............

insta]hng*

Integrated Panel material

%- 13A6"(16- 20 mm) panel thickness
Adequately sealed to withstand moisture (122°F/50°C @80% RH)

the

Panelpanel
screws(6)

Integ___

Integrated rectangular badge (1)
(Satinchrome supplied)

Panel