Fisher & Paykel DD24DCHTX7-88638-A, DD24DCX7-84690-B, DD24DCX7-88637-A Installation Guide
iNSTALLATiON iNSTRUCTiONS
DishDrawer TM dishwasher
DD24D 7 & DD24DT 7 models
US CA
Fisher Paykel
_90204D 04'/3
FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR MODEL
STANDARD HEIGHT DOUBLE MODELS
CIassic
DD24DCX7
DD24DCW7
DD24DCB7
i
PARTS SUPPLIED
OPTIONALLY HARD WIRING
PRODUCT & CABINETRY
DIMENSIONS (STANDARD HEIGHT)
CAVITY PREPARATION
m
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
,L
l ]
SECURE WITHOUT SECURE BY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (a) METHOD (b)
CHOOSE
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICITY
FINAL CHECKLIST
TROUBLESHOOTING
J
T
Designer
ooo
DD24DDFX'7
F
PARTS SUPPLIED
OPTIONA LLY HA RD WIRING
PRODUCT & CABINETRY
DIMENSIONS (STANDARD HEIGHT)
CAVITY PREPARATION
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
f
SECURE WITHOUT SECURE BY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (a) METHOD (b)
L
CHOO5E
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICITY
FINAL CHECKLIST
ooo
l
TROUBLESHOOTING
Integrated CIassic Designer
DD24DI7
PARTS SUPPLIED
OPTIONALLY HARD WIRING
M
PRODUCT & CABINETRY
DIMENSIONS (STANDARD HEIGHT)
CUSTOM PANEL CALCULATIONS
CA VITY PREPA RATION
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
[
SECURE WITHOUT SECURE BY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (a) METHOD (b)
W
INSTALL THE FRONT PANELS
CHOOSE
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICIT_
FINAL CHECKLIST
TROUBLESHOOTING
E]
/
DD24DCTX7
DD24DCHTX7
DD24DCTW7
DD24DCTB7
PARTS SUPPLIED
OPTIONALLY HARD WIRING
PRODUCT & CABINETRY
DIMENSIONS (TALL HEIGHT)
CA VITY PREPA RATION
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
i
f 1
SECUREWITHOUT SECUREBY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (a) METHOD (b)
L J
7
CHOO5E
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICITY
FINAL CHECKLIST
TROUBLESHOOTING
TALL HEIGHT DOUBLE' MODELS
ooo
DD24DDFTX'7
000
]
PARTS SUPPLIED
OPTIONALLY HARD WIRING
PRODUCT & CABINETRY
DIMENSIONS (TALL HEIGHT)
CAVITY PREPARATION
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
f
SECURE WITHOUT SECUREBY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (a) METHOD (b)
L
CHOO5E
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICITY
FINAL CHECKLIST
TROUBLESHOOTING
Integrated
DD24DTI7
DD24DHTJ7
T
PARTS SUPPLIED
OPTIONALLY HARD WIRING
PRODUCT & CABINETRY
DIMENSIONS (TALL HEIGHT)
CUSTOM PANEL CALCULATIONS
CAVITY PREPA RATION
MAXIMUM DISTANCE OF HOSES
& CORD FROM CHASSIS EDGE
[
SECURE WITHOUT SECUREBY
DRAWER REMOVAL DRAWER REMOVAL
RECOMMENDED ALTERNATIVE
METHOD (_) METHOD (b)
INSTALL THE FRONT PANELS
CHOOSE
DRAINAGE OPTION
CONNECT TO WATER & ELECTRICITY
FINAL CHECKLIST
TROUBLESHOOTING
J
SAFETY AND WARNINGS-ALL MODELS
3
Electrical hazard
Before installing the dishwasher, remove the house fuse or open the circuit
breaker. If permanently connecting the dishwasher, be sure the power is isolated
and the dishwasher unplugged.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown,
grounding wi[[ reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having
an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is installed and grounded in accordance
with all local codes and ordinances. WARNING - Improper connection of the
equipment-grounding conductor can result in a risk of electric shock. Check with
a qualified electrician or service representative if you are in doubt as to whether
the appliance is properly grounded.
If the dishwasher is installed as a permanently connected appliance:
GROUNDING INSTRUCTIONS -This appliance must be connected to a grounded
metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding
terminal or lead on the appliance.
Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.
Failure to follow this advice may result in electrical shock or death.
Cut hazard
installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these instructions with the Customer
installation must comply with your local building, electricity, and plumbing regulations.
At the completion of the dishwasher installation, the installer must perform the Final Checklist.
Remove all packaging materials supplied with the dishwasher
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. it is the responsibility of the plum ber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.
The switched power outlet must be outside the dishwasher cavity, so that it is accessible after
installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord and hoses.
ff the dishwasher is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should
not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.
ff the product is installed in a motor vehide, boat or similar mobile facility, you must bring the vehicle,
boat or mobile facility containing the product to the service shop at your expense or pay the service
technician's travel to the location of the product.
SAVETHESEINSTRUCTIONS
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
ADDITIONAL SAFETY AND WARNINGS- INTEGRATED MODELS ONLY
Electrical Shock Hazard
WARNING: To reduce the risk of electrical shock, fire, or injury to persons, the
installer must ensure that the dishwasher is completely enclosed at the time
of installation.
Before fitting the front panels, make sure that the dishwasher is disconnected
from the power supply.After installing the front panels, the installer must
ensure that the following components are electrically grounded: the panel
bracket and any custom metal component (e.g. handle) that extends past the
rubber sea[.
Failure to follow these warnings may result in electrical shock, injury or fire.
Read these instructions completely and careful_yo
Ensure the product is not plugged in.
Installation of custom panels requires basic mechanical and electrical skills.
installation must comply with your local building and electricity regulations.
Failure to install the custom panels correctly could invalidate any warranty or liability claims.
SAVETHESEINSTRUCTIONS
PARTS SUPPLIED ° ALL MODELS
Drain hose Drain hose Wire clip (2) Clamp (1) Side mounting Top Phillips Rubber
support (1) joiner (1) (for securing (for securing bracket kit mounting %" (16 mm) washer for
Moisture protection Hexagonal
tape (1) . socket for feet
(to prevent mois[ure adjustment (2)
damage) (long & short)
Drain hosejoiner) Drain hose joiner) (A and B) (2) brackets (2) screws (9) inlet hose (1)
OPTIONAL OPTIONAL (comes already
fitted)
/fthe Droin hosessupplied ore not long enough
to reoch your services,you must useo Droin Hose
f!_'tensionKit P/N 525Y98which will extend the droin
Prefinished toekick (1)
Edge Protector (1)
(If the services hole is through
a metal partition the hole
must be protected with the
Edge protector supplied to
prevent damage to the power
cord or hosesJ
hosesby 11' 70"(Zdm).
fhe kit isovoi/ob/e from the neorest Fisher&PoyM/
Authorized _Serviced2nter, or fb// free 1.888.93d./872
or www.fisherpoykel.com
4
ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS
Panel mounting
screws (12)
Panel bracket (2)
(attached to product)
Toekick mounting bracket (1)
(A custom toekickpanel of any
material with thickness
_"-_" (9 - 19 ram) can be screwed
to the plastic toekick mounting
bracket)
Toekick
mounting
screws (5)
Q OPTIONALLY HARD
WIRING PRIOR TO INSTALLATION
_ REMOVE THE LOWER DRAWER
To prevent kinked hoses, we recommend
rotating the drawer anti-clockwise and
resting it on its side after removal.
/
Press the release tabs in on
either side and push back
to release drawer from
runners.
TERMINATE THE WIRING AS SHOWN
Remove knock-out for cable clamp and
fit a suitable cable clamp for the conduit.
Access
cover
REMOVE THE ACCESS COVER & POWER CORD
Electrical Shock Hazard
Before continuing, ensure that the product is
disconnected from the power supply.
Failure to follow this warning may result in
electrical shock, injury or fire.
\\
REFIT THE DRAWER ONTO THE RUNNERS & CLOSE
Ensure the drawer
tabs
,release clockwise back.
;'(1O0ram)
is now rotated
\\
Use copper conductors only.
Ensure the release tabs on
both sides are reset fully.
Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.
(5( PRODUCT DIMENSIONS
6
n_
I
K
Plan
D C
A
Product dimensions inches(mm)
F depth of front panel (exchande) 1 1/8"(29) 11A6"(18) % - 1¾6"(16-20) 1 Y8"(29) 1¼6"(18) % - lSA6"(16-20)
G height ofchassis 31 I%6"(811) 31 15Z6"(811) 31 15_6"(811) 331¼6"(855) 331¼6"(855) 331¼6"(855)
Side
STANDARD HEf,GH'T'MODEL,_ ?_LL HE#GH'T' MODELS
H heightof levellingfeet Y8- 2 11_6"(9-69) 2 3/8 -2 11_6"(9-69) 2 3/8 - 2 11_6"(9-69)2 3/8- 2 11_6"(9-69)2 3/8-2 11_6"(9-69) 2 3/8 - 2 11_6"(9-69)2
I depth of handle n/a 1%"(41) n/a n/a 1%"(41) n/a
J depth of toekick recess(toback of front panel)1 3_6 - 3 s/8"(30-92) 13_6 - 3 5/8"(30-92) 13_6 - 3 5_6"(30-84) 5 13_6 - 3 5/8"(30-92) 13_6 - 3 5/8"(30-92) 13_6 - 3 5_6"(30-84) 5
K height of upper front pane[ 15 1/2"(394) 15 1¼6"(398) min. 15 11A6"(398) 17 1/4"(438) 17 3/8"(442) min. 17 3/8"(442)
L ventiDtion gap between front panels ¾6"(5) 546t'(8) min. sA6"(8) 346"(5) sA6"(8) min. sA6"(8)
M height of toekick panel (adjustabk?) 2 % - 4 3_"(70-120) 2 % - 4 3/4"(70-120) 2 % - 4 3_"(70-120) 2 3__ 4 3_"(70-120) 2 % - 4 3/4"(70-120) 2 % - 4 3_"(70-120)
N height of drawer fronts 291¾6"(757) 30"(762) min. 28 1/4"(717) 291¼6"(754) 29 lSA6"(760) min. 29 lSA6"(760)
0 height from top of handle to top of front panel n/a 2 Y2"(64) n/a n/a 2 1/2"(64) n/a
UnchdesXJ'(2mm) high bracketslots 2dependingon adjustment of levelingfeet _assumingfFont_:s_ne[thicknessof 1}46'(18mm) _adjustableto matchtoekick recessonadjoining cabinetry
Sassumingthat toekickmounting bracketisusedwith a%/'(18ram) thickcustom panel; if _'ecessisbetwe_:n1_'_J'-3%/'(50andtY/_ram) dee:p, thepanelwill need to be cut out - seestep'CustompanelcalcuDtion{
Loading...