Fisher 13293 Parts Manual
Replacement Parts for Backsplash Faucets
fisher manufacturing company
2000-5003
SEAT WASHER
RIGID
13188
CONTROL VALVE
LEVER HANDLE
LH SWIVEL STEM
RH SWIVEL STEM
2000-7500
SCREW
2000-8000
RED BUTTON
AND
2000-8001
BLUE BUTTON
2000-2301
2000-3002
BIBB CAP
10464
DUCK GASKET
2000-5000
WASHER
3000-0010
OR
3000-0011
1000-7502
SCREW
10456
LUBE
10014 (24”)
10022 (36”)
SUPPLY LINE
1/2” F X 1/2” F
10049 (24”)
10006 (36”)
SUPPLY LINE
1/2” M X 1/2” F
3000-0000
RH SWIVEL STEM
REPAIR KIT
OR
3000-0001
LH SWIVEL STEM
REPAIR KIT
1792
ANGLE STOP
WITH KEY
1790-1
ANGLE STOP
W/ CROSS
HANDLES
3969
6” RIGID
GOOSENECK
SPOUT
3966
12” RIGID
GOOSENECK
SPOUT
2400-2103
ELBOWS
8” C/C Backsplash Faucet
Product Installation Guide
Since 1936, Fisher Manufacturing Company has
manufactured heavy-duty, high quality plumbing
products and hardware specialties for the food service
industry. For three generations, the Fisher family has
adhered to a strict dedication of and overall value.
When you install Fisher products… you install
the best. Our hardware is manufactured with the
standardization of internal mechanisms. All chrome
plating is triple plated copper, nickel and chrome
for durability. Every piece of equipment we make is
rigorously tested in both our modern in-house testing
center and in actual fi eld situations under extreme
conditions. Every detail is thoroughly checked. Before
we make our products available to you, they pass
each and every test. You get proven performance.
Guaranteed.
Limited One Year Warranty
Fisher Manufacturing Company warrants its products
and parts thereof (except as noted below) against
defects in materials or workmanship for a period of
one year after the date of original purchase. During
this period Fisher Manufacturing Company will
replace a defective product or part without charge to
you, provided that the entire product is delivered to
Fisher Manufacturing Company. All transportation and
insurance charges for shipping the product to and from
Fisher Manufacturing Company must be borne by you.
Charges for transportation and insurance may, at the
option of Fisher Manufacturing Company, be refunded
depending upon our investigation of the warranty
claim. This warranty does not cover external fi nish
(except at date of original purchase) or labor costs
not specifi cally authorized by Fisher Manufacturing
Company.
A full and complete copy of our One Year limited
warranty is available upon request.
#13307- 8” c/c Backsplash Faucet with 12” Rigid
Gooseneck Spout
#13293- 8” c/c Backsplash Faucet with 6” Rigid
Gooseneck Spout
3200-2306
CONCENTRIC
FLANGES
PART NO. 42854
18694
1/2” CONCENTRICS
2200-5000
CONCENTRIC
GASKETS
MANFACTURING COMPANY
PO BOX 60, TULARE, CA 93275
(800)421-6162, FAX: (800)832-8238
www.fisher-mfg.com
1000-8002
SLIP JOINT KIT
REV. A
KEEP THIS MANUAL FOR FUTURE REFERENCE
ANSI/A112.18.1M, ANSI/NSF 61.9
fisher manufacturing company - toll free: 800-421-6162 fax: 800-832-8238
www.fi sher-mfg.com
Installation Instructions for Backsplash Faucets
BE SURE TO CHECK WITH YOUR LOCAL DEPARTMENT HAVING JURISDICTION
REGARDING BACKFLOW PREVENTION
Installation Instructions Continued
Installation Notes:
• Be sure to shut off water supply before beginning.
• Use pipe thread sealant such as PST on all threaded joints.
• Check the packaging for missing items BEFORE beginning installation. If items are missing, contact your supplier.
Tools Required for Installation
• Medium Sized Crescent Wrench
• Pipe Thread Sealant
PST
Package Contents
The box should contain the following:
Control Valve
Qty: 1
Rigid Gooseneck Spout
Length determined by model
Qty: 1
3200-2306
Concentric
Flanges
Qty: 2
18694
1/2” Concentrics
Qty: 2
2200-5000
Concentric Gaskets
Qty: 2
1000-8002
Slip Joint Kit
Qty: 2
10456
Lube
Installation Instructions
1. After unpacking items and checking for missing components, insert the gasket into the groove
on the concentric. Making sure gasket is in place, tighten the concentric and fl ange onto the
control valve body.
2. Mount control valve body to the backsplash by inserting the concentrics through the backsplash
and attaching slip joints. Tighten concentrics and attach elbows and supply lines (not included)
as required. Be sure to use pipe thread sealant on all threads.
3. Installing a rigid mount spout, apply thread sealant to male threads on the spout and insert into
control valve. Tighten until secure.
4. Turn on water supply and check for leaks.
Step 2
Step 3
Ø7/8”
Elbows
(not included)
Slip Joints
7 3/4” - 8 1/4”
[196.9 - 209.6mm]
Apply Thread
Sealant Here
Supply lines
(not included)
Step 1
Step 4
Gasket
Concentric
Flange
Loading...