Page 1
Indoor/Outdoor Digital Wireless
Camera with 7" LCD Monitor
Model DW-700/702
USER'S MANUAL
Page 2
©2010 Lehigh Consumer Products, LLC
All rights reserved. Distributed by Lehigh Consumer Products, LLC, Macungie, PA 18062. Due to
continuing product development, the product inside the packaging may look slightly different than
the one on the package.
Lehigh Consumer Products, LLC is a subsidiary of Jarden Corporation (NYSE: JAH). To obtain
warranty service, contact the Consumer Affairs Division at 1-800-323-9005, Monday through
Friday, 7:30 a.m. - 5 p.m., Central Standard Time.
Made in China
M08-0242-000
Page 3
Table of Contents
Safety ...............................................................................................................................1
Safety Precautions ........................................................................................................................... 1
FCC Compliance ............................................................................................................................. 1
Getting to Know Your DW-700/702 Security System....................................................2
Check Package Contents.................................................................................................................. 2
Digital Wireless Camera.................................................................................................................. 3
Digital Wireless Receiver ................................................................................................................ 4
Remote Control................................................................................................................................ 5
Display Screen Icons ....................................................................................................................... 6
Setting Up Your DW-700/702 Security System.............................................................7
General Precautions ......................................................................................................................... 7
Installing the Camera....................................................................................................................... 7
Installing the Receiver ..................................................................................................................... 8
Operating Menus.............................................................................................................9
Main Menu Operation...................................................................................................................... 9
Camera Setup................................................................................................................................. 10
Camera ON/OFF.................................................................................................................... 10
Camera Brightness................................................................................................................. 10
Pairing.................................................................................................................................... 11
Resolution .............................................................................................................................. 11
Recorder Setup............................................................................................................................... 12
Alarm Period.......................................................................................................................... 12
Motion Detection Record Period ........................................................................................... 13
SD Card Overwrite ................................................................................................................ 13
Event List....................................................................................................................................... 14
System Setup ................................................................................................................................. 14
Quad Display ......................................................................................................................... 15
Scan Period ............................................................................................................................ 15
Timing Setting ....................................................................................................................... 16
SD Card Format ..................................................................................................................... 16
Power Saving ......................................................................................................................... 17
TV Format.............................................................................................................................. 17
Set to Factory Default ............................................................................................................ 18
System Version .............................................................................................................................. 18
Page 4
Troubleshooting............................................................................................................19
Technical Information...................................................................................................21
General........................................................................................................................................... 21
Camera........................................................................................................................................... 21
Wireless ......................................................................................................................................... 21
Recording....................................................................................................................................... 21
Storage Data Management ………………………………………………………………………22
Warranty.........................................................................................................................23
Product Limited Warranty.............................................................................................................. 23
Warranty Exclusions...................................................................................................................... 23
Obtaining Service .......................................................................................................................... 24
Page 5
SAFETY PRECAUTIONS
Do not drop, puncture, or disassemble the camera.
Never tug on the power adapter. Use the plug to remove it from the wall.
Use the device with care. Avoid pressing hard on the camera or receiver body.
Do not expose the camera to high temperatures.
For your own safety, avoid using the camera when there is a storm or lightning.
Use the device with care. Avoid pressing hard on the camera body.
Do not crush or damage the power cable.
FCC COMPLIANCE
Safety
This device complies with Part 15 of the FCC Rules. Operation is subjected to the
following two conditions: (1) this device may cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur with a particular
installation. If this equipment does cause interference to radio or television equipment
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
received is connected.
Consult the dealer or an experience radio/TV technician for help.
Notice: Changes or modifications to the product could void the user's
authority to operate the product.
1
Page 6
Getting to Know Your
DW-700/702 Security System
Congratulations on purchasing your First Alert Security Camera product. First Alert has
been helping families and businesses stay safe for over 50 years. By having a First Alert
Security Camera, you’re taking the first step in protecting your home or business from
damage or theft. We’re watching, even when you’re not.
CHECK PACKAGE CONTENTS
Model DW-700 is a one-camera security system and Model DW-702 is a two-camera
security system. The technical specifications, installation, and operation of each model are
identical.
After unpacking the carton, check the contents for damage. Contact your supplier or dealer
immediately if any part is missing or damaged.
DW-700 DW-702
Digital Wireless Camera (1) Digital Wireless Camera (2)
7” LCD Digital Wireless Receiver (1) 7” LCD Digital Wireless Receiver (1)
Camera Stand (1) Camera Stand (2)
Mounting Kit (1) Mounting Kit (2)
Remote Control (1) Remote Control (1)
Power Supply (2) Power Supply (3)
AV Cable (1)
2GB SD Card
User’s Manual (1) User’s Manual (1)
AV Cable (1)
2GB SD Card (1)
2
Page 7
Getting to Know Your DW-700/702 Security System
Model DW-700/702 User's Manual
DIGITAL WIRELESS CAMERA
1 Antenna 7 IR LED
2 EDS 8 Camera Stand
3 Power LED 9 Pairing Key
4 Camera Lens 10 Power Jack
5 Link LED 11 Microphone
6 PIR 12 Power Supply
3
Page 8
Getting to Know Your DW-700/702 Security System
Model DW-700/702 User's Manual
DIGITAL WIRELESS RECEIVER
11
12
10
13
15 14
Link indicator Steady light when camera is operating; Flashing light when camera is
1
Power indicator Lights when receiver is powered on
2
3
4
5
6
7
8
OK
MENU
ESC
REC
9
DEL
recording
Cursor up in Menu mode; Switch channel in View mode
Cursor left in Menu mode; Volume down in View mode
Cursor right in Menu mode; Volume up in View mode
Cursor down in Menu mode; Switch channel in View mode
Confirm the settings/changes in Menu mode: Enter Event List in View
mode
Back in Menu mode;
Enter/exit Menu mode in View mode
Record in Menu mode;
Start/stop recording View mode
10
Power
11
IR Sensor
12
Speakers
13
SD Card Slot
14
AV Out Jack
15
DC In Jack
4
Page 9
Getting to Know Your DW-700/702 Security System
Model DW-700/702 User's Manual
REMOTE CONTROL
12
3
5
8
9
4
6
7
8
7
1
2
3
4
Start/Stop manual recording (SD card must be installed)
Enter Event List directly;
Press button to play/pause the video files
Press to delete video files you selected
In view mode, display up to four images cameras at one
time (audio is unavailable in QUAD Mode)
5
Enter/exit a menu
6
Press to turn on the Motion Detection
7
In Menu Mode, move between the selections
In View Mode, switch channel
In QUAD Mode, [Hot key CH1/CH2]
8
In Menu Mode, move between selections
In View Mode, audio volume down/up
In Play Mode, rewind/fast forward
In QUAD Mode, [Hot key CH3/CH4]
OK
9
Press to confirm the selections and changes
5
Page 10
Getting to Know Your DW-700/702 Security System
Model DW-700/702 User's Manual
DISPLAY SCREEN ICONS
6
Page 11
Setting Up Your
DW-700/702 Security System
GENERAL PRECAUTIONS
Use only the power supply provided with the system.
Unplug the power supply when the system is not in use for extended periods.
Do not place any of the equipment near a radiator, vent, or other place where it
might be exposed to heat, moisture, dust, vibrations, or strong magnetic fields.
Do not attempt to repair the camera. Contact a qualified technician or the dealer for
service. Any change or modification may damage the equipment and invalidate the
warranty.
When installing the camera, follow manufacturer’s advice when using power tools,
steps, ladders, etc. and wear suitable protective equipment (e.g., safety goggles)
when drilling holes. Before drilling holes through a ceiling, check for hidden
electricity cables and water pipes.
INSTALLING THE CAMERA
1 Select the position for the camera and secure the camera stand.
Screws and anchors are supplied. Use an appropriate screw type for the mounting surface.
2 Screw the camera onto the bracket.
7
Page 12
Operating Menus
Model DW-700/702 User's Manual
3 Adjust camera to the proper view angle. Make sure the lens is upright relative to your
subject. Tighten the thumb bolt.
4 Screw the antenna into place on the rear of the camera. Adjust the antenna to an
upright position.
INSTALLING THE RECEIVER
Connect the power cable to the DC IN of the receiver.
1
2 Plug the power supply into the electrical outlet.
3 Once the receiver is connected, see Camera Setup, Pairing (Operating Menus) to link
the camera(s) to the receiver.
OPTIONAL: VIEW ON TELEVISION OR OTHER MONITOR
1 If connecting to another
monitor such as a TV:
Connect the AV cable into
the AV OUT of the
receiver.
2 Connect the two RCA
jacks to the TV AV IN.
Yellow = Video; White =
Audio
3 Press POWER button to
turn on the receiver.
8
Page 13
Operating Menus
This chapter provides information about the menu screens. The screens are used to control
the various functions of the DVR system. The user selects options from a series of menus and
executes the actions by using the keypad on the IR controller.
MAIN MENU OPERATION
The Main Menu display when the system is powered up. Use this menu to access:
Camera Setup
Camera On/Off
Camera Brightness
Pairing
Resolution
Recorder Setup
Alarm Period
Motion Detection
SD Card Overwrite
Event List
System Setup
Quad Display
Scan Period
Time Setting
SD Card Format
Power Saving
TV Format
Set to Factory Default
System Version
9
Page 14
Operating Menus
Model DW-700/702 User's Manual
CAMERA SETUP
Access the Camera Setup menu from the Main Menu. Use this menu to turn the camera
on/off and adjust image brightness, pairing, resolution and quality.
CAMERA ON/OFF
1. Use
2. Press
to select a camera.
to turn camera ON/OFF.
Make sure unavailable cameras are set OFF from SCAN or QUAD mode.
CAMERA BRIGHTNESS
1. Use
2. Press
3. Use
to select a camera.
to display Camera Brightness bar.
to adjust Brightness.
1
10
Page 15
PAIRING
1. Use
2. Press
3. Within 60-second countdown, press LINK on the camera cable. Image will
display when pairing is complete.
RESOLUTION
1. Use
2. Press
to select a camera.
to start system countdown from 60 seconds.
to select Resolution between 640x480 and 320x240.
to confirm.
Resolution will affect recording file size. System can support longer
recording time for QVGA resolution and low image quality.
11
Page 16
Operating Menus
Model DW-700/702 User's Manual
RECORDER SETUP
Access the Recorder Setup menu from the Main Menu. Use this menu to set the alarm and
motion detection record periods, and to overwrite the SD card.
Recorder Setup
ALARM PERIOD
1. Use
10 sec, 15 sec. (Default setting is 5 sec.)
Alarm Period
Motion Detection
OK
SD Card Overwrite
to select a different Alarm Period for motion detection: OFF, 5 sec,
2. Press
to confirm.
Press any button to mute when motion detection alarm is activated.
12
Page 17
MOTION DETECTION RECORD PERIOD
1. Use
10 sec, 15 sec. (Default setting is 5 sec.)
to select a different Motion Detection Record Period: OFF, 5 sec,
2. Press
to confirm.
Motion detection will be disabled for 5 seconds after motion detection
recording or alarm stops.
SD CARD OVERWRITE
1. Use
2. Press
to select ON/OFF. (Default setting is ON.)
to save and exit.
Newly recorded file will overwrite original files when SD card memory
is full. SD card storage room indicator on LCD flashes a red warning
with 0.0G
13
Page 18
Operating Menus
Model DW-700/702 User's Manual
EVENT LIST
Access the Event List menu from the Main Menu.
Play Mode
1. Press
2. Continue to press
3. Press
to enter Record Folder.
to Play/Pause file.
to adjust volume up; press to adjust volume down; press ESC to
Stop/Exit.
Event List
1. Press DEL to enter deletion mode.
2. Use
3. Press
4. Press
to delete the selected file or delete all files.
and select icon.
to delete.
SYSTEM SETUP
Access the System Setup menu from the Main Menu. Use this menu to select quad scan,
adjust scan period and system clock, format the SD card, set the power saving and TV
format parameters, reset the system to factory default settings, and check system
information.
14
Page 19
QUAD DISPLAY
1. Use
to select Quad display ON/OFF.
2. Press
to confirm the change.
3. Turn all available channels ON before changing to Quad mode.
4. To exit the Quad display, press directional keys to enter single channel:
= CAM1; = CAM2;
= CAM3; = CAM4
Quad mode is recommended when the system is equipped with more than
one camera. The system will only record one channel, not the Quad display.
SCAN PERIOD
Scan Period selects the time each camera will be displayed.
1. Use
to change Scan Time interval: OFF, 5 sec, 10 sec, or 15 sec.
2. Press
to confirm the change.
This function is available for multi-camera systems. Only camera of current
display can be triggered during scan time. Recommended scan time is 5 sec.
Scan Time turns off when CH+, CH-, or REC is selected for manual scan
or record.
15
Page 20
Operating Menus
Model DW-700/702 User's Manual
TIMING SETTING
1. Press
2. Press to change the Time Setting.
to change Clock: Year, Month, Day, Hours, and Minutes.
3. Press
SD CARD FORMAT
1. Press
2. Press
Start
Make sure SD card is unlocked.
For first time use, it is strongly recommended to format the SD card.
to confirm the settings.
to select SD Card Format screen.
and press to format card.
16
Page 21
POWER SAVING
1. Use
When Power Saving mode is ON, the monitor screens turns off after a
2-minute idle time. Speaker volume remains on.
2. Press any key to activate monitor screen from Power Saving mode.
to turn Power Saving mode ON/OFF. (Default setting is ON.)
TV FORMAT
1. Use
PAL.)
to select TV Format: NTSC or PAL. (Default is NTSC. Do not use
Changing the TV format may affect the scale of the displayed images. Make
sure the format selected matches the TV used.
17
Page 22
Operating Menus
Model DW-700/702 User's Manual
SET TO FACTORY DEFAULT
1. Press
2. Press
to select Factory Default screen.
Start
and press to reset the system to factory default settings.
SYSTEM VERSION
Cam1
Cam2
Cam3
Cam4
----
----
----
----
----
1. Press
to select System Version screen.
For factory use only.
18
Page 23
Troubleshooting
Problem Possible Causes Remedies
System message
shows “No Signal”
Low or unstable
signal
No power supply to
camera
Channel is not linked up
to camera
Service out of range Move the camera closer to the receiver.
Signal is blocked If possible, remove major obstacles in
Antenna direction is
limited
Signal has been blocked If possible, remove major obstacles in
Strong radio signal
nearby
If camera power status indicator light is off,
check power adapter and power cable
connection.
Move the camera closer to the receiver, and
connect the camera to the desired channel. Go
to “Camera Setup” in the Menu. Use the
“Pairing” sub-menu to connect the camera to
the receiver.
between the camera and the receiver. Or,
relocate the camera to another location.
Adjust the camera antenna and receiver
position.
between the camera and receiver. Or, relocate
the camera to another location.
Keep WIFI router away from the camera
and/or receiver.
Channel(s)
disappear during
auto or manual scan
Dim or overly bright
image at night time
Recording does not
work
Motion detection
does not work
Strong electromagnetic
interference nearby
Scan channel(s) has been
turned OFF
Low light vision distance
is too short/too far or a
glass pane is too close
No SD Card Insert SD Card.
SD Card locked Unlock the SD Card.
Motion Detection record
time is set to OFF
Keep active appliances such as hair dryers,
heat fans, air conditioners, water pumps, or
microwave ovens away from the camera
and/or receiver.
Go to Menu; turn ON the channel(s).
Adjust the camera to have the view fit the
ideal distance: 15 to 24ft.
Always set Motion Detection record period to
5 sec, 10 sec, or 15 sec.
19
Page 24
Technical Information
Model DW-700/702 User's Manual
Audio feedback Camera and receiver are
too close
The camera has a high sensitivity
microphone. Keep the camera at least 10 feet
away from the receiver. If the camera must be
within 10 feet of the receiver, keep the
volume down.
Poor image quality Interference Place the camera and/or receiver antenna at a
new angle or readjust its position to make an
improvement.
Remove obstacles between the camera and
receiver that might affect the signal (e.g.,
furniture, cabinets, and walls.)
Relocate the camera closer to the receiver.
20
Page 25
GENERAL
Operating Power 5V
Operating Temperature 14°F - 122°F
Indoor / Outdoor Both
Technical Information
Dimensions
Camera & Stand
Receiver
Remote Control Included
4 Camera Multi-View Yes
CAMERA
Image Sensor CMOS
Viewing Angle 56 degrees
Audio Range 16 ft.
Digital Yes
Color Yes
Motion Detection Yes
Night Vision Capability Yes
Number of Infrared LEDs 27
Night Vision Distance up to 40 ft.
WIRELESS
4.7” x 2.8” x 2.7”
9.0” x 5.5” x 1.4”
Wireless Range 750 ft.
Frequency 2.4 GHz
Transmission Channels 40
RECORDING
Data Storage Type 2GB SD Card
SDHC Compatible 32GB
(included)
21
Page 26
Technical Information
Model DW-700/702 User's Manual
TORAGE DATA MANAGEMENT
S
SD Card Capacity 640 x 480 (VGA) 320 x 240 (QVGA)
1G 110 Minutes 165 Minutes
2G 250 Minutes 350 Minutes
8G 1070 Minutes 1450 Minutes
16G 2170 Minutes 2960 Minutes
22
Page 27
Warranty
PRODUCT LIMITED WARRANTY
BRK Brands, Inc., (“BRK”) the maker of First Alert® brand products warrants that for a
period of one year from the date of purchase (the “Warranty Period”), this product will be
free from defects in material and workmanship. BRK, at its sole option, will repair or
replace this product or any component of the product found to be defective during the
Warranty Period. Replacement or repair will be made with a new or remanufactured
product or component. If the product is no longer available, replacement may be made
with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser only from the date of initial retail
purchase and is not transferable. In order to obtain warranty service, you must keep the
original sales receipt and proof of purchase in the form of the UPC code from the package.
BRK dealers, service centers, or retail stores selling BRK products do not have the right to
alter, modify or any way change the terms and conditions of this warranty.
WARRANTY EXCLUSIONS
Parts and Labor: 1 year limited (warranted parts do not include bulbs, LEDs, and batteries)
This warranty does not apply to bulbs, LEDs, and batteries supplied with or forming part
of the product.
This warranty is invalidated if non- BRK accessories are or have been used in or in
connection with the product or in any modification or repair is made to the product.
This warranty does not apply to defects or damages arising by use of the product in other
than normal (including normal atmospheric, moisture and humidity) conditions or by
installation or use of the product other than in strict accordance with the instructions
contained in the product owner’s manual.
This warranty does not apply to defects in or damages to the product caused by (i)
negligent use of the product, (ii) misuse, abuse, neglect, alteration, repair or improper
installation of the product, (iii) electrical short circuits or transients, (iv) usage not in
accordance with product installation, (v) use of replacement parts not supplied by BRK,
(vi) improper product maintenance, or (vii) accident, fire, flood or other Acts of God.
This warranty does not cover the performance or functionality of any computer software
included in the package with the product. BRK makes no warranty that the software
provided with the product will function without interruption or otherwise be free of
anomalies, errors, or “Bugs.” This warranty does not cover any costs relating to removal or
replacement of any product or software installed on your computer.
BRK reserves the right to make changes in design or to make additions to or improvements
in its products without incurring any obligations to modify any product which has already
been manufactured. BRK will make every effort to provide updates and fixes to its
23
Page 28
Warranty
Model DW-700/702 User's Manual
software via its website. This warranty does not cover any alteration or damage to any
other software that may be or may become resident on the users system as a result of
installing the software provided. This warranty is in lieu of other warranties, expressed or
implied, and BRK neither assumes nor authorizes any person to assume for it any other
obligation or liability in connection with the sale or service of the product. In no event
shall BRK be liable for any special or consequential damages arising from the use of the
product or arising from the malfunctioning or non-functioning of the product, or for any
delay in the performance of this warranty due to any cause beyond its control.
BRK does not make any claims or warranties of any kind whatsoever regarding the
product’s potential, ability, or effectiveness to prevent, minimize, or in any way affect
personal or property damage or injury. BRK is not responsible for any personal damage,
loss, or theft related to the product or to its use for any harm, whether physical or mental
related thereto. Any and all claims or statements, whether written or verbal, by
salespeople, retailers, dealers, or distributors to the contrary are not authorized by BRK,
and do not affect this provision of this warranty.
BRK’s responsibility under this, or any other warranty, implied or expressed, is limited to
repair, replacement or refund, as set forth above. These remedies are the sole and exclusive
remedies for any breach of warranty. BRK is not responsible for direct, special, incidental,
or consequential damages resulting from any breach of warranty or under any other legal
theory including but not limited to, loss profits, downtime, goodwill, damage to or
replacement of equipment and property and any costs of recovering, reprogramming or
reproducing any program or data stored in or used with a system containing the product
accompanying software.
BRK does not warrant the software will operate with any other software except that which
is indicated. BRK cannot be responsible for characteristics of their party hardware or
software which may effect the operation of the software included.
Except to the extent prohibited by applicable law, any implied warranty of merchantability
or fitness for a particular purpose is limited in duration to the duration of the above
Warranty Period. Some states, provinces, or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights that vary from state to
state, or province to province, or jurisdiction to jurisdiction.
OBTAINING SERVICE
If service is required, do not return the product to your retailer. In order to obtain warranty
service, contact the Consumer Affairs Division at 1-800-323-9005, 7:30 a.m. – 5:00 p.m.
Central Standard Time, Monday through Friday. To assist us in serving you, please have
the model number and date of purchase available when calling.
After contacting the Consumer Affairs Division and it is determined that the product
should be returned for Warranty Service, please mail the product to: Lehigh, 2834
Schoeneck Rd, Macungie, PA 18062-9679.
24
Loading...