Fiat Croma 2000 CHT, Croma 2000 CHT 1989, Croma 2000 CHT 1990, Croma 2000 CHT 1991 Data Book

Download

Page 1

FIAT

Croma 2000 CHT

1989 to 1991

Notes and Illustrations

Weber DAT

1995 cm3, 8V

Engine and cooling system

Type Capacity (cm

) / number of cylinders Compression ratio / pressure bar Oil pressure bar Oil temperature ºC Valve clearance - inlet mm

Valve clearance - exhaust mm

Firing order No 1 cylinder position Thermostat opening temperature ºC Radiator cap pressure bar

Fuel system

Idle speed - manual [auto] rpm Fast idle speed - manual [auto] rpm CO @ idle speed [3000 rpm] - see page VI % HC @ idle speed [3000 rpm] - see page VI ppm CO2 @ idle speed [3000 rpm] - see page VI % O2 @ idle speed [3000 rpm] - see page VI % Carburettor / fuel injection

Type / ref Main jet / needle

Injection pressure bar Pump pressure bar Octane rating RON

Ignition system

Type Ignition coil

Primary resistance ohms

Ballast resistor ohms

Voltage - Tmnl 15(+) to earth V Distributor

Points gap (air gap) mm

Dwell angle º (%)

Condenser capacity µF

Rotation Ignition timing - basic [static º Crankshaft @ rpm

V = Vacuum NV = No Vacuum Total ignition advance º Crankshaft @ rpm

º Crankshaft @ rpm º Crankshaft @ rpm

Centrifugal check. º Crankshaft @ rpm

º Crankshaft @ rpm º Crankshaft @ rpm

Vacuum range check mbar

Maximum vacuum advance º Crankshaft

Spark plugs

Type

Electrode gap mm

Electrical system

Battery V / CC / RC Alternator voltage / full load current / engine rpm Starter motor current / voltage - cranking A / V

Starter motor current / voltage - locked A / V

Running gear

Brakes -

Front (min. friction material thickness) mm

Rear (min. friction material thickness) mm

Tyres

Saloon Size

Estate / Van Size

Pressure - front / rear - Saloon bar

Pressure - front / rear - Estate / Van bar

Front suspension / wheel alignment

Toe-in (+) / Toe-out (–) mm [º]

Camber

Castor

King pin inclination

Rear suspension / wheel alignment

Toe-in (+) / Toe-out (–) mm [º]

Camber

Torque wrench settings

Cylinder head - stage 1 Nm

Cylinder head - stage 2 Nm

Cylinder head - stage 3 Nm

Cylinder head - stage 4 Nm

Big-end bearings Nm Main bearings Nm Clutch cover Nm Flywheel [driveplate] Nm Front hubs Nm Rear hubs Nm Wheel nuts / bolts Nm Spark plugs Nm

Capacities

Engine oil & filter litres Gearbox - 4-speed [5-speed] litres Automatic transmission - refill litres Final drive litres Cooling system litres Fuel tank litres

154 C2.000 DOHC 8V 72kW 1995 / 4

9.5±0.15 / _ [3.4 to 4.9] 100

0.35±0.04

0.40±0.04 1-3-4-2 TBE 81 to 85

0.98

800±50 _

1.5±0.5 ≤1200 _ _ Weber 34 DAT 55/150 95, 105 _

0.24 to 0.29 98[E 95 RON]

Digiplex 2 Marelli BAE 504D

0.405 to 0.495 _ _ Marelli _ _ _ _ 10±2 BTDC @ 500 to 1000 _ 32±2 BTDC @ 5000 _ _ Computer control _ _ Computer control _ Bosch/Champion WR6DC / RN7YCC

0.85 to 0.95

12 / 210 / 65 (45Ah)

14.0 to 14.3 / 65, 70 / 3500 270 / 9.2 _

1.5

1.5 175/70x14: 195/60x14

_ 175: 2.0 / 2.0

-1.0 to +1.0

-20’±20’ +1°50’ to 2°30’ _

+2.0 to 5.0

-20’±20’

20 40 + 90° + 90° 25 + 50° 20

20 142 450 locked

320 86 25 to 30

5.5

1.75

3.3 WT

9.0 70

195: 2.2 / 2.2

Centre bearing: + 120°. Others: + 80°

Click on one of the

buttons above to view

data for this car. To

return to this screen and

make another choice, click anywhere on the

data screen.

Automotive Technical

DATA BOOK

Croma 2000 CHT 1989 to 1991

FIAP5002011

Engine &

Cooling

Fuel Ignition Electrical

Running

gear

Torque

settings

Capacities

Notes &

Illustrations

MENU HELP

1: Idle speed 2: CO / Mixture