Fetco EXTRACTOR CBS-1131V+, EXTRACTOR V+ Series, EXTRACTOR CBS-1151V+, EXTRACTOR CBS-1132V+, EXTRACTOR CBS-1152V+ Programming Manual

Programming Guide

CBS-1100V+™

Models:
CBS-1131V+; CBS-1132V+
CBS-1151V+; CBS-1152V+

[phone] [phone] [e-mail] www.fetco.com

© 2008-2018 Food Equipment Technologies Company Part # P172 January 2018

FETCO®, EXTRACTOR® and V+ are trade mark s or trade names of Food Equipment Technologies Company.

A

A

(

)

A

A

A

Scroll Across (A-F)

(

)

PROGRAMMING MENU LAYOUT CBS V+ Series

[A] PROGRAM

[B] GENERAL [C] INPUTS [D] OUTPUTS [E] OTHER
Batch A1. to A7 B1.0 to B1.7 C1.0 to C1.3 D1.0 to D1.5 E1.0 to E1.8
| | | | |

10 PERMANENT

Position A10&A40 are permanent

|

| | | |

| | | |

11 Brew Volume B1 Tank Temp C1 LLC Probe D1 Test Heater E1 Display Firmware

| | | | |

A12 Brew Time B2 [Brew at Temp] C2 B. Basket Sensor D2 Test Fill Valve E2 Sel. Brewer Model

| | | | |

A13 Prewet Percent B3 LLC Sensitivity C3 Tank water temp. D3 Test R. Brew Valve E3 Display Errors

Scroll Down

| | | | |

A_4 Prewet Delay

only when prewet % >0%

B4 Temperature F/ C C4 Keypad Test D4 Test L. Brew Valve E4 Clear Errors

| | | |

A16 Drip Delay B5 Volume unit G or L D5 Screen Brightness E5 Reload Defaults

1-8

| | |

A20 Batch ACTIVATE? B6 Left Flow Rate E6 Save to USB

| | |

30 Batch ACTIVATE? B7 Right Flow Rate E7 Load through USB

| | |

40 PERMANENT B8 Slow Mains Flow E8 Demo Mode

|

A50 Batch ACTIVATE?

|

A60 Batch ACTIVATE?

|

70 Recipe Copy?
Use this chart to quickly locate and access programming topics.
The topics are in groups A-E in this guide.
“F” screen is Save and Exit
Check the user guide for more comprehensive details of the brewer settings.
User guides are located online at fetco.com in Service-Resources….or use our QR code

Popular Operator Control Settings Default Settings-(Factory Settings)

CBS-1131V+

CBS-1151V+

Parameter Name

CBS-1132V+

CBS-1152V+

A11 Brew Volume 3 LTR 1.5 GAL
A12 Brew Time (Min:Sec) 4:00 4:00
A13 Prewet Percent 0% 0%

Prewet Delay (Min: Sec)

A14

1:00 1:00

This appears only when Prewet >0%

A16 Drip Delay (Min:Sec) 1:30 1:30

B1 Hot Water Tank Temp. 200 F 200 F
B2 Brew at Set Temperature “YES” [ON] “YES” [ON]
B3 LLC Sensitivity (See User Guide) “LOW” LOW”
B4 Temperature Scale F F
B5 Water Volume Scale Liters Gallons

1.55 LPM 3.40 LPM

B6 & B7 Brew Valve Flow Rate

FLOW rate is in Liters/Min even if brewer is in Gallons

Batch Activate

A(20, 30&50,60)

[Batches on buttons 2&3 and 5&6 if dual]

Go to Parameter E5 to reset all settings to factory defaults.

Yes-Active Yes-Active

HOW TO ENTER PROGRAMMING MODE TO ACCESS CONTROLS AND DIAGNOSTICS

)

g

A

A

1)Turn the brewer off by pressing the power switch.
Turn power switch “ON”

2

DISPLAY

-The display will progress through startup screens.

Example:

Brewer and version code

CBS-1132V+

v 1 . 0. 1744

-The STOP button will illuminate. As shown—right

3)-Quickly press the STOP button (no need to hold)

-Brewer is now in PROGAMMING MODE…

Menu Topic

-F

Menu Position

1-7

Toggle Setting

UP or [YES]

4)Press the STOP button to advance the menus

across the top A-F and back to START (“A”)

Toggle Setting

DOWN or [NO]

5)Press 1 to ent er menus for individual settings under letter

NOTE: Buttons li

ht up only when they are available to make adjustment

Batch Settings

dvance through settings

CBS-1132V+

STOP

1
2

3

STOP

CBS-1132V+

The menu topics are numbered A1-A7; B1-B8 -etc…

-Press button 1 to select recipe programming

Position name, topic & reference position show in display.

First programming position

A11 is shown in example

BREW VOLUME

A11 3.00 L ±

-Toggle buttons 2 and 3 to make changes.

STOP

1

2

3

STOP

-Then press button 1 to advance to next programming topic.

To change recipes

A

Illustration shows each recipe batch position

All recipe programming is made from the “A” screens
TO ACCESS BATCH RECIPES:

CBS-1132V+

STOP

STOP

-Enter “A”-BATCH PRG

10

-Press button “A10” to scroll through the parameters

A20

Press “STOP” to scroll across the other recipe buttons
Single brewer has 3 recipes. Twin brewer has 6 recipes

A30

-All recipe settings are programmed from the “A” screen.
Each recipe button may be individually programmed.
Top recipe buttons (A10&A40) are permanent. Lower recipe buttons
(A20, A30&A50, A60 if dual can be hidden. To hide or deactivate a
button: toggle the BATCH ACT screen.

A11 screen sets the total brew volume

Note

:

some water is retained in the used coffee grounds

BATCH ACT

A20 YES –

BREW VOLUME

A11 3.00 L ±

Toggle to NO to deactivate

or hide lower recipes

First programming position
A11 is shown in example

A40

A50

A60

-Scroll down (press button A10) to the next setting A12 to set brew time to
dispense the volume set in A11.

Note: goes to default setting if set too short for volume entered

BREW TIME

A12 04:00 ±

Second programming position
A12 is shown in this example

- Press A10 button continue scrolling down through A13-A15 for all
recipes. (See user guide for detailed explanation of each parameter)

-After all brew recipes are set press STOP button to go to–GENERAL “B”
B1 is Tank Tem p era tu re

This controls the brew water temperature and the hot water service faucet
Toggle buttons A20 and A30 to make changes
Then press A10 to advance

Tank Temp

B1 200F ±

First programming position “B1”
Is for hot water tank temperature

B2 is Brew at Temperature
Default is YES. Brew will not start until

Brew @ Temp
B2 YES -

Brew pauses & will start when hot
water tank temp. is at setpoint

hot water tank temperature is at setpoint.
If Brew at Temp is set to “NO”-brew will start at any temperature above
77°C/170°F. Toggle buttons A20 & A30 to adjust
Then press A10 to advance

-Following the PROGRAMMING MENU LAYOUT chart shown on page 2
Complete your adjustments in the GENERAL –“B” paramete r

- Settings found under BATCH PROGRAM “A” GENERAL “B include most
needed for start-up and operation.

-Always verify the model number (displayed when brewer first powered
ON). Model selection is found in E2

-Always SAVE & EXIT as shown in screen “F” or new settings will be lost.
Press A10 to advance though the settings to change or check settings

-then press STOP to continue scrolling across C-E positions

Batch Parameters –A-MENU and PROGRAMMING

Brewers are shipped with all recipe batch buttons enabled and set to the defaults shown in A1-A6.
These are full batches. Adjust settings of the individual recipes under batch PRG “A”

Position Name and default setting Range Comment

A.20,30
A.50,60

A1

A2
A3
A4
A6

Batch
Enabled or Disabled

Brew Volume

3 liters CBS-1130V+

1.50 gal CBS-1150V+
Brew Time (Min: Sec)

4:00
Prewet Percent
0%
Prewet Delay
00:00 (Min:Sec)
Drip Delay
1:30 (Min:Sec)

The top batch on each side

YES/NO

cannot be disabled. (A10&A40)

CBS-1130V+

0.95 – 4.75 (Liters)
CBS-1150V+

To switch between gallons and
liters, go to position B5

0.50-2.00 (Gallons)
Factory default total brew is 5:30

2:00 – 12:00

(4:00 brew time+1:30 drip delay)

0.00 – 15.0%
0:10 – 5:00

Prewet must be > 0%

Percentage of total brew
volume.
The time between end of prewet
cycle and start of brew cycle.

0:30 – 6:00 Minutes Brew switch continues to flash.

B-E Advanced Settings and Diagnostics

Batch Parameters – B-GENERAL settings

Position Name and default setting Range Comment

B1
B2
B3
B4
B5
B6
B7

Tank Temperature
93° C -or- 200°F
Brew at Temp. Setpoint
“YES”
LLC Sensitivity
“LOW”
Temperature Scale
“°F” Fahrenheit
Volume Scale
L-(

CBS-1130) G-(CBS-1150)

LEFT brew valve flow rate

NOTE: flow rate only in liters per min

RIGHT brew valve flow rate

NOTE: flow rate only in liters per min

70° to 96°C
157° to 205°F

YES/NO
LOW/HIGH
°F/°C

Liters/Gallons
User adjustable

CBS-1130 1.55L/0.40G

CBS-1150 3.40L/0.9G

CBS-1130 1.55LPM
CBS-1150 3.40LPM

NOTE: Equipment factory
default is set for metric
Batch to start when at set
temperature: SEE USER GUIDE
High is only for low mineral or
R.O water SEE USER GUIDE
NOTE: Changing will overwrite
user settings

CBS-1130V+ factory set in liters
CBS-1150V+ factory set in gallons

Adjusts the brew valve flow rate.

SEE USER GUIDE

Adjusts the brew valve flow rate.

SEE USER GUIDE
Trims fill system for low flow
from supply

B8

Mains low flow

NO/YES

“NO”

Batch Parameters – C-INPUTS controls & conditions

Position Name and default setting Range Comment

LLC Probe Continuity

Reading of tank water

Reading of tank water resistivity

C1

Direct Read

resistivity in TDS

in TDS

C2 Brew Basket Sens or YES/NO YES or NO

Tank Temp.

C3

Direct Read

Hot water tank

Hot water tank temperature

temperature

Checks buttons under

C4 Keyboard Test All buttons

membrane cover

Batch Parameters – D-OUTPUTS settings

Position Name and default setting Range Comment

D1 Heater Test

ON/OFF

10 seconds maximum ON time

ON/OFF

D2 Fill Valve Test

10 seconds maximum ON time

Energizes Heaters!
For diagnostics/service use only

Tests Fill Valve

D3 Left Valve Test

10 seconds maximum ON time

Tests Left Brew Valve

ON/OFF

ON/OFF

D4 Right Valve Test

10 seconds maximum ON time

NOTE: If heater or valve are switched “ON” for testing they will automatically turn “OFF” in ten (10) seconds

LCD Brightness

D7

0-15

Default is 8

Tests Right Brew Valve
Adjust LCD screen brightness

only-Not for LEDs under buttons

Use this formula to compensate for minor discrepancies in actual volume versus programmed volume

=

New

Use this formula to determine the new setting:
Enter new setting in B6 or B7 -See user guide.

Measured Volume

Current

X

Programmed Volume Setting Setting

Use the formula above to compensate and fine-tune brew volume. TIP:check flow from supply for fouled water filter

Brew valve flow rates are in liter/min Enter the New Setting value into B6/B7 and save as in the “F” screen.

HINT: Set lower to incr ease volum e, hi gher to decreas e volum e.

Use this to compensate for minor discrepancies in actual volume versus programmed volume.

E3-Error Codes

DO NOT CLEAR ERROR CODE S UNTIL ERROR IS IDENTIFIED AND/OR CORRECTED Contact specialized personnel for error codes

Code Description Possible Cause Corrective Action

Software error-error on start up or

001

corrupted software
050 Short-circuit in temperature probe
051 Open temperature probe.

Initial Fill Error. Initial fill time took

100

longer than expected after power up.

Improper start-up or shutdown Restart , if still fault: reload software
Probe failure. Replace probe.

Bad probe connection, or probe failure. Check all connections. Replace probe if necessary.
Water supply flow rate is too low.

Watch for short potting during brew cycle. Investigate
cause of low flow rate. (Clogged water filter...)

Error on refill-. Tank did not refill within

101

Water supply flow rate is too low.

expected time.

Heater open, high limit thermostat

201

or Solid-State Relay (SSR) fault
255 Touch pad error

NO

Insert Brew Basket

BSKT

Consult the user guide for your brewer for more complete information

Failure of: heating element, SSR, high
Limit or low voltage

Keyboard contact longer than 2 min
Or faulty reassembly

Brew basket must be in place
This is a SAFETY FEATURE

Watch for short potting during brew cycle. Investigate
cause of low flow rate. (Clogged water filter…)

Check and replace heating elements if necessary.
Restart , if still fault: reload software. If mechanical:

replace membrane switch or control module
Insert brew basket into brewer rails to enable brewer

Batch Parameters – E-OTHER software and code settings

Position Name and default setting Range Comment

E1 Display Firmware 1.0.1744 Displays current version

CBS-1131

NOTE: Will need reboot

CBS-1132

E2 Select Model

CBS-1151
CBS-1152

1=Newest/6=Oldest

COMPLETELY OVERWRITES ALL
USER SETTINGS

See Error Code Chart

E3 Display Errors

LAST six errors only

for references
Resetting error codes should be after completing the servic e and factory diagnostics and
correcting any brewer faults. Clear error codes by cycling the brewer “OFF” then “ON”.

NOTE: Always contact FETCO

E4 Reset Errors YES/NO

Technical Service for errors

[phone]

Reset to default of

NOTE: COMPLETELY OVERWRITES

E5 (Reload) DEFAULTS

base model

ALL USER SETTINGS

E6 USB Data Save Save data to USB
E7 Load From USB Will need reboot Plug in USB flash-drive dev ice

Demonstrates the controls for

DEMO Mode

ON/OFF

training. Brewer will not brew

E8

when in demo mode.

Reset in E8 to “OFF” to exit

Batch Parameters F–HOW TO SAVE SETTINGS

–EXIT & RETURN TO PROGAMMING

IMPORTANT! After programming, you MUST SAVE your settings before exiting programming
mode or changes will be lost.
Settings are saved from the “F” screen as shown below.
You may exit programming at any time.
After programmed settings are saved, the brewer exits PROGRAMMING mode and returns to
regular brew operations. Settings are saved only when brewer returns to OPERATING MODE
DO NOT attempt to save by rebooting (turning power OFF then ON). All changes made will be
discarded and brewer will remain in the existing default settings.

Programming A-F

A - F

STOP

1
2

3

From any screen-Press

STOP button until the

EXIT (“F”) screen

appears

STOP

A4

A5

A6

EXIT

A4
A5

A6

F NO +

STOP

1
2

3

From the “F” screen

Press button 2 to

toggle to show the

EXIT-YES screen

STOP

EXIT

F YES –

STOP

STOP

A4
A5

A6

1

2

3

From EXIT-YES screen

Press button 1 to

toggle to show the

SAVE screen

SAVE

STOP

A4
A5

A6

F1 NO +

STOP

1

2

3

From SAVE screen

Press button 2 to

toggle to show the

SAVE-YES screen

SAVE

STOP

A4

A5

A6

F1 YES –

STOP

1
2

3

To SAVE and EXIT

Press button 1 to

SAVE your changes

and to EXIT to

OPERATING MODE