Festool TS 75 BROCHURE
No Compromises!
Perfection in XXL.
TS 75, the powerful and handy
plunge-cut saw with a 75 mm
cutting depth.
2
Up to 75 mm cutting depth – no comparison
The TS 75 saw can go where 65 mm saws can‘t. With its
75 mm cutting depth and powerful motor it is in its ele-
ment when sawing thick material such as 68 mm house
and safety doors.
Together with the guide rail, the TS 75 allows for flexible
working. Of course, it does this with the typical Festool
advantages for better, easier and faster working!
Easy-to-reach return stop.
The return stop prevents the saw jolting
back when it is plunged into the material.
It is housed within the practical depot
and is always within easy reach – thus
allowing you to work in safety.
Rotating extractor connector.
More freedom of movement, less wear.
The extractor hose never gets tangled,
does not get in the way and is, therefore,
always where it should be – this is
good for your health.
Electronically controlled.
The MMC electronics can be used to
adapt the speed to suit the material.
And the speed remains constant – even
when plunge-cutting. The saw blade
stops in 2 seconds thanks to the
quick-acting safety brake system
The TS 75 plunge-cut saw
Benefits at a glance
Up to
75 mm
cutting
depth
New!
Spring-loaded spacer wedge.
If it is in the way, it just disappears: the
spring-loaded spacer wedge retracts into
the housing automatically when the saw is
plunged into the material.
Sliding clutch.
If the saw blade gets jammed, the sliding
clutch prevents the saw from jolting back.
plug it connection
and Softgrip
New!
3
A wide range of possibilities.
FastFix saw blade
changing system.
The saw blade can now be changed in
just a few simple moves. This means you
can change the blade more often to suit
the material you are working on.
Triple bearing.
The triple bearing of the motor
improves the running smoothness
and extends the service life.
Zero-play guidance.
The guidance jaws on the guide
rail can be set using just two
fingers. This allows for zero-play
guidance of the machine, which in
turn increases the cutting quality.
Splinterguard on both sides.
Splinter-free sawing on both sides. The
clip-on splinterguard combined with the
guide rail make this possible.
Exact depth setting.
The notched depth stop makes this possible: cutting depth setting is acccurate to
the millimetre.
To ensure that every cut is made successfully, Festool offers a
wide range of 120 mm diameter saw blades. Every saw blade
model is tailored for a specific range of applications to guaran-
tee optimum work results as well as saving time and money.
In addition, thanks to the FastFix saw blade changing system,
every saw blade can be changed quickly and easily.
Ordering information can be found on Page 7.
Panther circular saw blade
For rapid sawing with low application of
power, especially in the case of rip cuts in
solid wood. Suitable for hard and soft woods.
Special circular saw blade
for aluminium
Ideal for aluminium panels and profiles as
well as for hard and fibre-reinforced plastics.
Flat-tooth circular saw blade
Thanks to its slightly chamfered teeth,
this saw blade is ideal for sawing steel cable
ducts, steel plate and steel profiles.
Special circular saw blade
for laminates
With a special fine-grain carbide, this blade is
ideal for laminated boards and mineral mate-
rials, giving a much longer service life.
Fine-tooth circular saw blade
The fine-cut blade for clean cross-cuts free of
splinters in solid wood. Also for laminated or
veneered board materials.
18-tooth circular saw blade
The sturdy blade for all building panels, soft
plastics and wood.
Universal circular saw blade
The all-rounder for working on all types of
wood and wooden materials as well as build-
ing panels, plasterboard and soft plastics.
Loading...