LEVEL SET BUFFER
10
LEDs
9V DC
INPUT
5 6
11
4
3
2
LEVEL SET BUFFER
1
1. Mute Footswitch
2. Tuner Output Jack
3. Jewel Indicator
4. Main Output Jack
5. Level
6. Hi-Freq
LEVEL HI-FREQ
LOAD
MUTE
7. Load Switch
8. Input Jack
9. Low Battery Indicator
10. LED Kill Switch
11. DC Power Connector
7
8
9
LEVEL SET BUFFER
Thanks for purchasing the Level Set Buffer—a flexible utility
pedal designed especially for electric guitar and bass. The
Level Set Buffer is designed to accomplish three main
functions. First, it provides a separate output for a stage
tuner in order to keep the signal path purer (the built-in mute
footswitch also allows silent tuning). Note that the tuner
output is always active, meaning that tuning can be done
mid-performance without having to mute the signal (if
preferred). Second, the Level and Hi-Freq controls allow
output-level compensation for different instruments,
enabling easier guitar swaps without having to adjust
multiple settings. Third, the pedal serves as a buffer that
helps maintain signal quality through multiple pedals and
cables. The Level Set Buffer is designed to be placed first in
the signal chain, with other pedals following.
DESIGNED IN CALIFORNIA, U.S.A.
Level
This control offers up to 12dB of volume boost or cut, with the center
position being unity gain (no level change). With the player’s main
instrument, begin by setting this control to the center position and
then dialing in the rest of the rig. Then adjust the Level control up or
down as needed depending on the output level of subsequent
guitars. Humbucking or active pickups may require a cut in gain
(counter-clockwise) while vintage single-coil type pickups might
require more gain (clockwise) to sound right.
Hi-Freq
The Hi-Freq gain control behaves similarly to the Level control,
except that it only affects very high frequencies. This control is
designed to add a little sparkle to darker pickups, or to warm up
overly bright pickups. Like the Level control, this control offers up to
12dB of boost or cut.
Load Switch
The Load Switch applies capacitance to the input and loads guitar
pickups in the same way that a traditional tube amp might. Note that
the effect can be subtle, and the results will differ depending on (as
with a tube amp) the type of pickups in use, instrument volume pot
value and setting, and cables.
Jewel Indicator
The jewel is illuminated when the pedal is not muted, letting players
know they’re ready to rock.
Mute Footswitch
This rugged footswitch mutes the main output jack, to allow for silent
tuning.
Input Jack
This is a high-impedance input suitable for electric guitar, bass,
acoustic guitars with pickup systems, keyboards and other
instruments.
Main Output Jack
This is a low-impedance output jack that connects to the amp or to
the next effect pedal in the signal chain.
Tuner Output Jack
This jack connects to a tuner’s input jack.
DC Power Connector
This is a standard, center-negative 9VDC jack for use with
appropriate power supplies.
LED Kill Switch
This switch extinguishes the LEDs that illuminate the knobs—useful in
maximizing battery life when running the pedal from batteries.
Low Battery Indicator
This red LED on the front of the battery door illuminates when battery
voltage drops below a set threshold, indicating that the battery
should be replaced soon.
FENDER MUSICAL INSTRUMENTS CORPORATION
A PRODUCT OF:
CORONA, CALIFORNIA, USA
Fender® is a registered trademark of FMIC.
Copyright © 2018 FMIC. All rights reserved.
P/N 7713288000 - REV A
Important Safety Instructions
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC
power to rain or moisture.
•Do not alter the AC plug of the connected power adapter
•Do not drip or splash liquids on the unit.
•No user serviceable parts inside, refer servicing to qualified personnel only.
• WARNING: The unit must only be connected to a safety agency certified, regulated,
power source (adapter), approved for useand compliant with applicable local and
national regulatory safety requirements.
• Unplug the AC power adapter before cleaning the unit exterior. Use only a damp cloth
for cleaning and then wait until the unit is completely dry before reconnecting it to power.
• Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable
of producing very high sound pressure levels which may cause temporary or permanent
hearing damage. Use care when setting and adjusting volume levels during use.
Languages
Manual available in Espanol, francais, Italiano, Deutch, Portugues, (Chinese)
www.fender.com/support
Expanded Owner’s Manual
Expanded Owner’s Manual available at:
www.fender.com/support
Specifications
IMPEDANCES:
POWER SUPPLY:
POWER REQUIREMENTS:
DIMENSIONS:
WEIGHT:
Product specifications subject to change without notice
INPUT: 1MΩ OUTPUT LOAD: >10kΩ
One 9V battery or 9VDC regulated adapter,
5.5 x 2.1 mm barrel connector, center negative
14mA @ 9VDC
64mA, Total Current Consumption
2.75” x 4.9” x 2.5” (95.25mm x 124.5mm x 63.5mm)
.9lbs (.40kg)
NOTES:
© FENDER MUSICAL INSTRUMENTS 2018
Loading...