THE SOUND THAT CREATES LEGENDS
Bullet Amp
TYPE: PR 241
Owner,s Manual
P/N 041526
Bullet / Bullet Reverb Owner’s Manual
The Fender Bullet / Bullet Reverb amplifiers present the
player with the best value of any gain switching amplifier in
its price class. The common equalization section consists of
TREBLE and BASS controls in addition to Fender's exclusive
MID control. This control provides midrange "tone shaping"
that will continuously vary your sound from smooth and
bluesy to a punchy honk, or all the way back to 0 for the
ultimate heavy metal overdrive! The NORMAL channel
consists of a VOLUME control, while the DRIVE channel
consists of VOLUME and GAIN controls which together set the
overall level for the DRIVE channel. The DRIVE channel also
incorporates Fender's innovative "smooth dipping' circuit.
This circuit concept is designed to simulate the way tubes dip
and produce the overdrive distortion sound so popular with
musicians today.
Bullet / Bullet Reverb Sound Settings
Just Pick It - Any Guitar / Any Pick-Up Combination
Also included is an EXTERNAL 8 Ω SPEAKER output jack
which automatically disconnects the internal 8" speaker when
used. The HEADPHONES jack automatically mutes the
speaker in addition to driving Stereo or Mono headphones.
The built in quality of a Fender amplifier is the result of over
four decades of dedication in the combined skills of research
and development by our engineers and musicians.
That is why we proudly say...FENDER,
Creates Legends
.
The Sound That
Hard Rock - Strat / Bridge Position
Dirty Blues - Strat / Neck Position
Total Shred - Any Guitar / Bridge Position
Bullet / Bullet Reverb Front Panel Functions
A B
A. INPUT - A high impedance, high sensitivity plug-in
connection for instruments.
B. NORMAL VOLUME - Adjusts the overall loudness of the
Normal Channel.
C. GAIN - Adjusts the amount of preamp amplification in
the Drive Channel. Cleaner sound is achieved at lower
gain settings; high gain settings will produce more
sustain and distortion. This control works in conjunction
with the
loudness of the Drive Channel.
D. DRIVE SELECT - Activates the Drive Channel.
E. DRIVE VOLUME - Adjusts the overall loudness of the
Drive Channel.
F. TREBLE - Adjusts the amount of boost or cut in the high
frequency range.
G. MID - Adjusts the overall tone quality without affecting
the signal level. High MID settings will provide emphasis
in the midrange frequencies whereas a lower setting will
notch the midrange to produce sounds characteristic of
most “metal” music.
DRIVE VOLUME
D E F
C
control (item E) to set the overall
G
I. REVERB - ( BULLET REVERB ONLY.) Adjusts the amount
J. EXTERNAL SPEAKER - This jack provides an output to
K. HEADPHONES - This jack provides an output to
L. POWER INDICATOR - When this indicator is
M. POWER SWITCH - This switch turns the AC power ON
H
of reverberated signal mixed with the original dry
signal for both the Normal and Drive channels.
an external speaker enclosure. The enclosure must
have a minimum impedance of 8Ω Use of this jack
automatically disables the internal speaker.
PLUG HEAD PHONES IN HERE.
standard stereo or mono headphones for private
listening. NOTE: Use of this jack automatically disables
the speaker. CAUTION: Prolonged listening at high
levels may be hazardous to your hearing! This jack can
also be used as an unbalanced line output by using
either a stereo or mono 1/4 inch phone plug
connection.
illuminated the Bullet / Bullet Reverb is receiving AC
power.
and
OFF.
completely shut down.
I
When the switch is
J
K
OFF
the amplifier is
L
DO NOT
M
H. BASS - Adjusts the amount of boost or cut in the low
frequency range.
LINE CORD - This amplifier is equipped with a grounding
type supply cord to reduce the possibility of shock hazard.
Be sure to connect it to a grounded receptacle.
ALTER THE AC PLUG.
DO NOT
Bullet / Bullet Reverb Specifications
PART NUMBER: Bullet Amp Bullet Reverb Amp
120V VERSION: 22-6705 120V VERSION: 22-6706
230V VERSION: 22-6765 230V VERSION: 22-6766
INPUT IMPEDANCE: Greater than 1 Meg Ohm
NOMINAL INPUT LEVEL: 100 mV
POWER OUTPUT: 15 Watts R.M.S.
RATED LOAD IMPEDANCE: 8 Ohms
POWER REQUIREMENTS: 120V VERSION: 120 VAC 60 Hz., .28A Max.
230V VERSION: 230 VAC 50 Hz., .14A Max.
SPEAKER COMPLEMENT: One 8 Ohm Special Design 8” Speaker (P/N 025421)
DIMENSIONS: Height: 12-3/8” (31.4cm)
Width: 13-1/4” (33.7cm)
Depth: 7-1/8’ (18.1cm)
WEIGHT: 15lbs. (6.8kg)
SOUND: Unbelievable!!
WARNING:
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED
PERSONNEL ONLY.
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.,
CORONA, CA 91720
Loading...