Fantech HP Series, FR Series Installation Instructions Manual

Installation Instructions for

Radon Fans Model HP/FR

READ & SAVE THESE INSTRUCTIONS!

Warnings

DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED, MAKE SURE ELECTRICAL SERVICE TO THE FAN IS
LOCKED IN “OFF: POSITION.

1. Suitable for use with solid-state speed control.

2. This unit has rotating parts and safety precautions should be exercised during installation, operation and maintenance.

3. CAUTION: “For General Ventilation Use Only. Do Not Use To Exhaust Hazardous Or Explosives Materials and Vapors.”

4. WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS-OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the factory.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being

b.

switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.

c. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-

rated construction.

d. The combustion airflow needed for safe operation of fuel burning equipment may be affected by this unit’s operation. Follow the heating equip-

ment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the

American Society of Heating, Refrigeration, and Air Conditioning Engineers (ASHRAE) and the local code authorities.
e. When cutting or drilling into wall or ceiling, do not damage electrical wires or other hidden utilities.
f. Ducted fans must always be vented to the outdoors.
g. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
h. NEVER place a switch where it can be reached from a tub or shower.

5. WARNING! Check voltage at the fan to see if it corresponds to the motor nameplate.

GUARDS MUST BE INSTALLED WHEN FAN IS WITHIN REACH OF PERSONNEL OR WITHIN SEVEN (7) FEET OF WORK­ING LEVEL OR WHEN DEEMED ADVISABLE FOR SAFETY.

Wiring Diagram

Five (5) Year Warranty

This warranty supersedes all prior warranties

Installation that will result in condensate forming in the outlet ducting should have a condensate bypass installed to route the condensate outside of the fan
housing. Conditions that are likely to produce condensate include but are not limited to: outdoor installations in cold climates, long lengths of outlet duc­tion, high moisture content in soil and thin wall or aluminum outlet ducting. Failure to install a proper condensate bypass may void any warranty claims.

DURING ENTIRE WARRANTY PERIOD:

FANTECH will repair or replace any part which has a factory defect in
workmanship or material. Product may need to be returned to the fan­tech factory, together with a copy of the bill of sale and identified with
RMA number.

FOR FACTORY RETURN YOU MUST:

• Have a Return Materials Authorization (RMA) number

. This may be
obtained by calling FANTECH either in the USA at 1.800.747.1762
or in CANADA at 1.800.565.3548. Please have bill of sale available.

• The RMA number must be clearly written on the outside of the
carton, or the carton will be refused.

• All parts and/or product will be repaired/replaced and shipped back
to buyer; no credit will be issued.

OR
The Distributor may place an order for the warranty part and/or
product and is invoiced. The Distributor will receive a credit equal
to the invoice only after product is returned prepaid and verified
to be defective.

FANTECH WARRANTY TERMS DO NOT PROVIDE FOR REPLACEMENT
WITHOUT CHARGE PRIOR TO INSPECTION FOR A DEFECT. REPLACE­MENTS ISSUED IN ADVANCE OF DEFECT INSPECTION ARE
INVOICED, AND CREDIT IS PENDING INSPECTION OF RETURNED
MATERIAL. DEFECTIVE MATERIAL RETURNED BY END USERS
SHOULD NOT BE REPLACED BY THE DISTRIBUTOR WITHOUT
CHARGE TO THE END USER, AS CREDIT TO DISTRIBUTOR’S
ACCOUNT WILL BE PENDING INSPECTION AND VERIFICATION OF
ACTUAL DEFECT BY FANTECH.

THE FOLLOWING W

ARRANTIES DO NOT APPLY:

• Damages from shipping, either concealed or visible. Claim must be
filed with freight company

.

• Damages resulting from improper wiring or installation.

• Damages or failure caused by acts of God, or resulting from
improper consumer procedures, such as:

1. Improper maintenance

2. Misuse, abuse, abnormal use, or accident, and

3. Incorrect electrical voltage or current.

• Removal or any alteration made on the FANTECH label control num­ber or date of manufacture.

• Any other warranty, expressed, implied or written, and to any con­sequential or incidental damages, loss or property, revenues, or
profit, or costs of removal, installation or reinstallation, for any
breach of warranty.

WARRANTY VALIDATION

• The user must keep a copy of the bill of sale to verify purchase date.

• These warranties give you specific legal rights, and are subject to
an applicable consumer protection legislation. Y

ou may have addi-

tional rights which vary from state to state.

United States

1712 Northgate Blvd.,

Sarasota, FL. 34234

Phone: [phone]

Fax: [phone]

www.fantech.net; [e-mail]

Canada

50 Kanalflakt Way,

Bouctouche, NB E4S 3M5

Phone: [phone]

Fax: [phone]

www.fantech.ca; [e-mail]

Fantech, reserves the right to modify, at any time and without
notice, any or all of its products’ features, designs, components and
specifications to maintain their technological leadership position.

Article #: 301077

Item #: 401443

Rev Date: 010307