Fairchild Semiconductor FAN4113 Datasheet
Features at +1.2V
• 640µA supply current per amplifier
• 36MHz gain bandwidth product
• Output voltage range: 0.06V to 1.10V
• Input voltage range: -0.4V to +0.2V
• 8V/µs slew rate
• 12nV/√Hz input voltage noise
• Package option (SC70-5)
• Fully specified at +1.2V, +2.7V, and +5V supplies
Applications
• Cellular phones
• Personal data assistants
• A/D buffer
• DSP interface
• Smart card readers
• Portable test instruments
• Single cell NiCd/Ni MH powered systems
• Keyless entry
• Infrared receivers for remote controls
• Telephone systems
• Audio applications
Description
The FAN4113 is a low cost, voltage feedback amplifier that
consumes only 640µA of supply current. The FAN4113 is
designed to operate from +1.2V to 5.5V (±2.75V) supplies.
The common mode voltage range extends below the negative
rail and the output provides rail-to-rail performance.
The FAN4113 is designed on a complementary bipolar
process and provides 36MHz of bandwidth and 8V/µs of slew
rate at a low supply voltage of 1.2V. The combination of low
power, rail-to-rail performance, low voltage operation, and
tiny package options make the FAN4113 well suited for use
in personal electronics equipment such as cellular handsets,
pagers, PDAs, and other battery powered applications.
FAN4113
1.2V, 36MHz, Low Power Rail-to-Rail Amplifier
www.fairchildsemi.com
REV. 1 October 2001
Typical Application
Pin Assignments
-
+
1
2
3
Out
-V
s
+In
+V
s
-In
5
4
Non-Inverting Freq. Response, Vs = 1.2V
Vo = 50mV
pp
G = 1
G = 10
G = 5
G = 2
+V
s
6.8µF
+
+
FAN4113
-
0.01µF
R
f
+In
R
g
Normalized Magnitude (1dB/div)
0.01
0.1
1
Frequency (MHz)
10 100
Out
Absolute Maximum Ratings
Parameter Min. Max. Unit
Supply Voltages 0+6V
Maximum Junction Temperature – +175 °C
Storage Temperature Range -65 +150 °C
Lead Temperature, 10 seconds – +260 °C
Operating Temperature Range, recommended -40 +85 °C
Input Voltage Range -
Vs-0.5 +Vs+0.5
V
θjafor 5 load SC70 331.4°C/W
Electrical Specifications
(Tc= 25°C, Vs= +1.2V, G = 2, RL= 5kΩ to Vs/2, Rf= 5kΩ, V
o (DC)
= Vcc/2; unless otherwise noted)
Parameter Conditions Min. Typ. Max. Unit
AC Performance
-3dB Bandwidth
1
G = +2, Vo= 50mV
pp
20 MHz
Full Power Bandwidth G = +2, Vo= 500mV
pp
9 MHz
Gain Bandwidth Product 36 MHz
Rise and Fall Time 200mV
pp
25 ns
Overshoot 200mV
pp
6 %
Slew Rate 500mV
pp
8 V/µs
2nd Harmonic Distortion 0.5Vpp, 500kHz 75 dBc
3rd Harmonic Distortion 0.5Vpp, 500kHz 84 dBc
THD 0.5Vpp, 500kHz 0.018 %
Input Voltage Noise >100kHz 12 nV/√Hz
DC Performance
Input Offset Voltage 0.5 mV
Average Drift 2 µV/°C
Input Bias Current 400 nA
Average Drift 2 nA/°C
Input Offset Current 30 nA
Power Supply Rejection Ratio DC 80 dB
Open Loop Gain 65 dB
Supply Current 640 µA
Input Characteristics
Input Resistance 25 MΩ
Input Capacitance 1.8 pF
Input Common Mode Voltage Range -0.4 to 0.2 V
Common Mode Rejection Ratio 72 dB
Output Characteristics
Output Voltage Swing RL= 5kΩ to Vs/2 0.05 to 1.11 V
RL= 1kΩ to Vs/2 0.07 to 1.03 V
Output Current ±1.2 mA
Short Circuit Output Current ±1.8 mA
Power Supply Operating Range 1.2 1.2 5.5 V
Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are
determined from tested parameters.
Notes:
1. For G = +1, Rf= 0.
DATA SHEET FAN4113
2 REV. 1 October 2001
Electrical Specifications
(Tc= 25°C, Vs= +2.7V, G = 2, RL= 5kΩ to Vs/2, Rf= 5kΩ, V
o (DC)
= Vcc/2; unless otherwise noted)
Parameter Conditions Min. Typ. Max. Unit
AC Performance
-3dB Bandwidth
1
G = +1, Vo= 50mV
pp
42 MHz
G = +2, Vo= 50mV
pp
20 MHz
Full Power Bandwidth G = +2, Vo= 500mV
pp
9 MHz
Gain Bandwidth Product 35 MHz
Rise and Fall Time 200mV
pp
25 ns
Settling Time to 1% 1V
pp
200 ns
Overshoot 200mV
pp
4 %
Slew Rate 1V
pp
8 V/µs
2nd Harmonic Distortion 0.5Vpp, 500kHz 75 dBc
3rd Harmonic Distortion 0.5Vpp, 500kHz 84 dBc
THD 0.5Vpp, 500kHz 0.018 %
Input Voltage Noise >100kHz 12 nV/√Hz
DC Performance
Input Offset Voltage
2
-2.5 0.5 +2.5 mV
Average Drift 2 µV/°C
Input Bias Current
2
400 800 nA
Average Drift 2 nA/°C
Input Offset Current 30 nA
Power Supply Rejection Ratio
2
DC 66 80 dB
Open Loop Gain 70 dB
Supply Current
2
750 900 µA
Input Characteristics
Input Resistance 25 MΩ
Input Capacitance 1.4 pF
Input Common Mode Voltage Range -0.4 to 1.7 V
Common Mode Rejection Ratio
2
66 75 dB
Output Characteristics
Output Voltage Swing RL= 5kΩ to Vs/2
2
0.085 to 2.55 0.04 to 2.64 V
RL= 1kΩ to Vs/2 0.07 to 2.56 V
Output Current ±9 mA
Short Circuit Output Current ±11 mA
Power Supply Operating Range 1.2 2.7 5.5 V
Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are
determined from tested parameters.
Notes:
1. For G = +1, Rf= 0.
2. 100% tested at +25°C.
FAN4113 DATA SHEET
REV. 1 October 2001 3
Loading...