Superior CMR of 15,000V/µs min. (HCPL4503M)
No base connection for improved noise immunity
■
(HCPL4503M)
Applications
■
Line receivers
Pulse transformer replacement
■
■
Output interface to CMOS-LSTTL-TTL
Wide bandwidth analog coupling
■
Description
The HCPL4503M, 6N135M, 6N136M, HCPL2530M and
HCPL2531M optocouplers consist of an AlGaAs LED
optically coupled to a high speed photodetector transistor.
A separate connection for the bias of the photodiode
improves the speed by several orders of magnitude over
conventional phototransistor optocouplers by reducing
the base-collector capacitance of the input transistor.
The HCPL4503M has no internal connection to the phototransistor base for improved noise immunity.
An internal noise shield provides superior common
mode rejection of up to 50,000V/µs.
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
SymbolParameterConditionValueUnits
T
STG
T
OPR
T
SOL
EMITTER
I
(avg)DC/Average Forward Input
F
I
(pk)Peak Forward Input Current
F
I
(trans) Peak Transient Input Current
F
V
P
DETECTOR
(avg)Average Output Current Each
I
O
I
(pk)Peak Output Current Each
O
V
EBR
V
V
PDOutput Power Dissipation
I
Storage Temperature-40 to +125°C
Operating Temperature-40 to +100°C
Lead Solder Temperature
= 0 to 70°C unless otherwise specified. Typical values are measured at TA = 25°C and VCC = 5V.)
A
Switching Characteristics(V
Symbol ParameterTest ConditionsDeviceMin.Typ.Max.Unit
t
t
PLH
|CM
|CM
Notes:
6. The 4.1kΩ load represents 1 LSTTL unit load of 0.36mA and 6.1kΩ pull-up resistor.
7. The 1.9kΩ load represents 1 TTL unit load of 1.6mA and 5.6kΩ pull-up resistor.
8. Common mode transient immunity in logic high level is the maximum tolerable (positive) dV
of the common mode pulse signal V
Common mode transient immunity in logic low level is the maximum tolerable (negative) dV
of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO < 0.8V).
Propagation Delay
PHL
Time to Logic LOW
Propagation Delay
Time to Logic HIGH
|Common Mode
H
Tr ansient
Immunity at
Logic High
|Common Mode
L
Tr ansient
Immunity at
Logic Low
= 5V)
CC
TA = 25°C, RL = 4.1kΩ,
= 16mA
I
F
R
L
= 25°C
T
A
R
L
R
L
TA = 25°C, (RL = 4.1kΩ,
= 16mA
I
F
R
L
= 25°C
T
A
R
L
R
L
IF = 0mA, VCM = 10V
R
L
I
= 0mA, VCM = 10V
F
R
L
I
= 0mA, VCM = 1,500V
F
R
L
IF = 16mA, VCM = 10V
R
L
I
= 16mA, VCM = 10V
F
R
L
(6)
(Fig. 7)
= 1.9kΩ, IF = 16mA,
(7)
(Fig. 7)
= 4.1kΩ, IF = 16mA
= 1.9kΩ, IF = 16mA
(6)
(Fig. 7)
= 1.9kΩ, IF = 16mA
= 4.1kΩ, IF = 16mA
= 1.9kΩ, IF = 16mA
= 4.1kΩ, TA = 25°C
P-P
= 1.9kΩ, TA = 25°C
P-P
= 1.9kΩ, TA = 25°C
= 4.1kΩ, TA = 25°C
= 1.9kΩ
(8)
(Fig. 8)
(8)
(8)
(8)
P-P
(8)
P-P
IF = 0mA, VCM = 1,500V
R
= 1.9kΩ, TA = 25°C
L
, to assure that the output will remain in a logic high state (i.e., VO > 2.0V).
CM
6N135M0.231.5µs
HCPL2530M
6N136M
HCPL4503M
HCPL2531M
(6)
(Fig. 7)6N135M
HCPL2530M
(7)
(Fig. 7)6N136M
HCPL4503M
HCPL2531M
6N135M0.451.5µs
HCPL2530M
(7)
(Fig. 7)
6N136M
HCPL4503M
HCPL2531M
(6)
(Fig. 7)6N135M
HCPL2530M
(7)
(Fig. 7)6N136M
HCPL4503M
HCPL2531M
,
(Fig. 8)
,
(Fig. 8)
,
P-P
(Fig. 8)
,
(Fig. 8)
,
6N135M
HCPL2530M
6N136M
HCPL2531M
HCPL4503M15,00050,000
6N135M
HCPL2530M
6N136M
HCPL2531M
,
P-P
(8)
(Fig. 8)
HCPL4503M15,000 50,000
0.250.8µs
2.0µs
1.0µs
0.260.8µs
2.0µs
1.0µs
10,000V/µs
10,000V/µs
10,000V/µs
10,000V/µs
/dt on the leading edge
cm
/dt on the trailing edge
cm
Single-Channel: 6N135M, 6N136M, HCPL4503M
Dual-Channel: HCPL2530M, HCPL2531M — High Speed Transistor Optocouplers