Fairchild FST16861 service manual
查询FST16861供应商
FST16861
20-Bit Bus Switch
FST16861 20-Bit Bus Switch
March 2000
Revised March 2000
General Description
The Fairchild Switch FST16861 provides 20-Bits of highspeed CMOS TTL-compatible bus switching. The low ON
resistance of the switch allows inp uts to be connected to
outputs without adding propagation delay or generating
additional ground bounce noise.
The device is organ ized as a 10-bit or 20-Bit bus switch.
When OE
nected to Port 1B. When OE
to Port 2B. When OE
exists between the A and B Ports.
is LOW, the switch is ON and Port 1A i s con-
1
is LOW, Port 2A is connected
2
is HIGH, a high impedan ce state
X
Features
■ 4Ω switch connection between two ports.
■ Minimal propagation delay through the switch.
■ Low l
■ Zero bounce in flow-through mode.
■ Control inputs compatible with TTL level.
.
CC
Ordering Code:
Order Number Package Number Package Description
FST16861MTD MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide
Devices also availab le in Tape and Reel. Specify by appending th e s uffix let t er “X” to the ordering cod e.
Connection Diagram
Logic Diagram
Truth Table
Pin Descriptions
Pin Name Description
, OE
OE
1
1A, 2A Bus A
1B, 2B Bus B
© 2000 Fairchild Semiconductor Corporation DS500318 www.fairchildsemi.com
2
Bus Switch Enables
Inputs Inputs/Outputs
OE
LL1A = 1B 2A = 2B
LH1A = 1B Z
HL Z 2A = 2B
HH Z Z
OE
1
2
1A, 1B 2A, 2B
Absolute Maximum Ratings(Note 1) Recommended Operating
Supply Voltage (VCC)0.5V to +7.0V
DC Switch Voltage (V
FST16861
DC Input Voltage (V
DC Input Diode Current (l
DC Output (I
DC V
OUT
/GND Current (ICC/I
CC
Storage Temperature Range (T
) (Note 2) −0.5V to +7.0V
S
) (Note 3) −0.5V to +7.0V
IN
) VIN<0V −50mA
IK
) Current 128mA
) ±100mA
GND
) −65°C to +150 °C
STG
Conditions
Power Supply Operating (V
Input Voltage (V
Output Voltage (V
Input Rise and Fall Time (t
Switch Control Input 0nS/V to 5nS/V
Switch I/O 0nS/V to DC
Free Air Operating Temperature (T
Note 1: The “Absolute Maximum Ratin gs” are those v alues beyon d which
the safety of the dev ice cannot be guaranteed. T he device sh ould not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommend ed O peratin g Cond itions” t able w ill defin e the c ondit ions
for actual device operation.
is the voltage observed/applied at either the A or B Ports across
Note 2: V
S
the switch.
Note 3: The input and output negative volt age ratin gs may be exceede d if
the input and output diode current ratings are observed.
Note 4: Unused control inputs must be held high or low. They may not float.
(Note 4)
CC)
)0V to 5.5V
IN
)0V to 5.5V
OUT
, tf)
r
)-40 °C to +85 °C
A
DC Electrical Characteristics
V
Symbol Parameter
V
IK
V
IH
V
IL
I
I
I
OZ
R
ON
I
CC
∆ I
CC
Note 5: Typical values are at VCC = 5.0V and TA = +25°C
Note 6: Measured by th e v olt age drop between A and B pins at the indicate d c urrent through the switch. On resistance is det erm ined by the lower of the
voltages on the two (A or B) pins.
Clamp Diode Voltage 4.5 −1.2 V IIN = −18mA
HIGH Level Input Voltage 4.0–5.5 2.0 V
LOW Level Input Voltage 4.0–5.5 0.8 V
Input Leakage Current 5.5 ±1.0 µA0 ≤ VIN ≤ 5.5V
OFF-STATE Leakage Current 5.5 ±1.0 µA0 ≤ A, B ≤ V
Switch On Resistance 4.5 4 7 Ω VIN = 0V, IIN = 64mA
(Note 6) 4.5 4 7 Ω VIN = 0V, IIN = 30mA
Quiescent Supply Current 5.5 3 µAVIN = VCC or GND, I
Increase in I
per Input 5.5 2.5 mA One input at 3.4V
CC
CC
(V)
0 ±1.0 µAVIN = 5.5V
4.5 7 12 Ω VIN = 2.4V, IIN = 15mA
4.0 11 20 Ω VIN = 2.4V, IIN = 15mA
TA = −40 °C to +85 °C
Min
Typ
(Note 5)
Units Conditions
Max
CC
Other inputs at VCC or GND
4.0V to 5.5V
= 0
OUT
www.fairchildsemi.com 2
Loading...