Extron Electronics RGB 460xi User Manual

RGB 460xi Series

Architectural Series Interfaces
User Guide
Interfaces
68-542-01 Rev. G
07 11
Safety Instructions • English
This symbol is intended to alert the user of important operating and mainte­nance (servicing) instructions in the literature provided with the equipment.
This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product enclosure that may present a risk of electric shock.
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment. Retain Instructions • The safety instructions should be kept for future reference. Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information. Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment
manufacturer because they may be hazardous.
Warning
Power sources • This equipment should be operated only from the power source indicated on the product. This
equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of
the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched
by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To prevent
the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent
overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer instructions.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant
d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir. Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou
présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le
fabricant du matériel car cela risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie
aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Avertissement
Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce
matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les
cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne
ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un
technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les
composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement
avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der
Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose
ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand
darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empndlichen Teile im Inneren. Diese Öffnungen dürfen niemals von
anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien
nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre instrucciones impor­tantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre la presencia de elemen­tos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el
equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta. Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la
documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente
recomendados por el fabricante, ya que podrian implicar riesgos.
安全须知 中文
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴露的危险电压,有触电危险。
注意
阅读说明书 用户使 用该设备前必须阅读并理 解所有安全和 使用说明。 保存说明书 用 户应保存安全说明书以备将来使用。 遵守警告 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 不要使 用该产品厂商没有推荐的工具或追加设备,以避免危险。
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica
indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación
eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares
donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calicado. En el interior no
hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el
sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros
objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta
batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías
usadas siguiendo las instrucciones del fabricante.
警告
电源 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线(
地线)是安全设施,不能不用或跳过 。
拔掉电源 为安全 地从设备拔掉电源,请拔掉所有设备后或桌面电源的电源线,或任何接到市电
系统的电源 线。
电源线保护 妥善布线, 避免被踩踏,或重物挤压。 维护 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不 要自己试图打开设备盖子维修 该设备。
通风孔 有些设备机壳上有通风槽或孔,它们是用来防止机内敏感元件过 热。 不要用任何 东西
挡住通风孔。
锂电池 不正确的更换电池会有爆炸的危险。必须使 用与厂家推荐的相同或相近型号的电池。按
照生产厂的建议处理废弃电 池。
ii
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio commu­nications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and
related topics, click here.
iii
Conventions Used in this Guide
In this user guide, the following are used:
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
CAUTION: A caution indicates a potential hazard to equipment or data.
WARNING: A warning warns of things or actions that might cause injury, death, or
other severe consequences.
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1&* X2)* X2#* X2!
CE
}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are written in the font shown here:
From the File menu, select New.
Click the OK button.
Copyright
© 2011 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
iv

Contents

Introduction .......................................................... 1
About this Manual .............................................. 1
About the RGB 460xi Series ................................ 1
Features .............................................................. 2
Application Examples ......................................... 2
Installation and Operation ................................ 3
Installation Overview ........................................... 3
Installation Checklist: ...................................... 3
UL Guidelines .................................................. 4
Front Panel Features and Cabling ........................ 4
Rear Panel Features and Cabling ......................... 7
Euro Channel and Floor Box Versions ................ 10
Mounting Adapter Plates (AAPs or MAAPs) ....... 11
Pre-installation Testing ...................................... 12
Troubleshooting ............................................ 12
Interface Mounting ........................................... 12
Reference Information ....................................... 13
Specifications .................................................... 13
Ordering Information ........................................ 16
Accessories ....................................................... 17
Cables .............................................................. 17
AAP and MAAP Modules .................................. 18
RGB 460 Series • Contents v
RGB 460 Series • Contents vi

Introduction

This section provides an overview of this guide and describes the RGB 460xi architectural
interface series and its features.
Topics that are covered include:
About this Manual
About the RGB 460xi Series
Features
Application Examples

About this Manual

This manual describes the Extron RGB 460xi Series of universal wall, furniture, and floor box mountable interfaces and explains how to configure and operate them. Unless otherwise noted, the term “RGB 460xi” or “interface” is used throughout this manual to refer collectively to the RGB 460xi, RGB 464xi, and RGB 468xi and their variations. Where there
are differences, they are pointed out.
Detailed mounting instructions are available in other Extron publications which are available on the Extron Website:
For wall box installations, refer to one of the available wall box installation guides.
For MK box installations, refer to part number 68-636-02.
For wall or furniture mount installations with Euro Channel versions, refer to part
number 68-636-03.
For Steel City® floor box installations, refer to part number 68-636-04.
For FSR floor box installations, refer to part number 68-636-05.
For AKM UK floor box installations, refer to part number 68-904-01.

About the RGB 460xi Series

The Extron RGB 460xi, RGB 464xi and RGB 468xi are compact computer video interfaces. Each interface comes in either a two-gang (RGB 460xi), three-gang (RGB 464xi and RGB 468 Mxi), or four-gang (RGB 460xi MK and RGB 468xi) wall box size, except Steel City, MK, FSR, and AKM UK floor box models. Optionally, the 460xi and 468xi come in an EC version which mounts in a Euro Channel. The interfaces (except for the RGB 460xi MK, FSR, and AKM UK models) are also wall or furniture mountable and come with a matching mud ring kit (part number 70-519-xx). The interfaces have a 300 MHz ( – 3 dB) video bandwidth.
Each interface accepts one VGA-UXGA compatible computer video input (15-pin HD) and one stereo audio input. All models include a 15-pin HD buffered local monitor output.
RGB 460 Series • Introduction 1

Features

Projector
Installation Cable
SVGA Compatible Computer w/ Audio
AAPs
Extron RGB 468xi
INPUT
MONITOR
H. SHIFT
AUDIO
MIN/MAX
RGB 468
WITH ADSP
TM
MONITOR
NO MONITOR
Horizontal shifting control — The displayed image may be shifted to the left or right
by turning a front panel knob.
Advanced Digital Sync Processing (ADSP™) — ADSP allows sync processing
operations, such as horizontal centering, to occur without affecting the sync timing of the signal. This allows horizontal centering to be applied to signals that are output to digital display devices such as LCD projectors, DLP projectors and plasma displays. An internal DIP switch provides another option, Digital Display Sync Processing, (DDSP™), to ensure proper displays without altering sync pulse timing or width.
Stereo audio — Unbalanced stereo audio inputs can be output as balanced or
unbalanced unamplified stereo audio.

Application Examples

Installation Cable
Figure 1. RGB 460 Series Application Examples
Projector
H. SHIFT
MONITOR
MIN/MAX
INPUT
TM
MONITOR
AUDIO
WITH ADSP
NO MONITOR
RGB 460
Extron RGB 460xi
SVGA Compatible Computer w/ Audio
RGB 460 Series • Introduction 2

Installation and Operation

This section outlines installation and describes the front and rear panel features and how to
cable the RGB 460 series. Topics included are:
Installation Overview
Front Panel Features and Cabling
Rear Panel Features and Cabling
Euro Channel and Floor Box Versions
Mounting Adapter Plates (AAPs/MAAPs)
Pre-installation Testing
Interface Mounting

Installation Overview

CAUTION: Installation and service should be performed by authorized personnel

Installation Checklist:

Turn off all equipment. Disconnect all input and output devices from their power source.
If applicable, prepare the site as explained in the appropriate installation guide. Attach any optional architectural adapter plates (AAPs) to the interface (RGB 468xi,
RGB 468 Mxi, or RGB 468xi AKM UK only) and then attach all the cables (see “Front
Panel Features and Cabling” on page 4, “Rear Panel Features and Cabling” on
page 7, and “Mounting Adapter Plates (AAPs/MAAPs)” on page 11 ).
Set rear panel DIP switches as explained in “Rear Panel Features and Cabling” on
page 7.
Connect all output device, interface, and computer power cords and then turn on all
devices. All devices should have power, and the audio and video should be working properly. If not, check all cabling and switch settings, and make adjustments as necessary (see “Pre-installation Testing” on page 12).
Disconnect power from all the devices.
Mount the interface as explained in the appropriate installation guide.
Restore power to the devices.
only. UL Listed electrical boxes are recommended (see “UL Guidelines” in this chapter).
RGB 460 Series • Installation and Operation 3

UL Guidelines

To comply with Underwriters Laboratories (UL) safety requirements, the following minimum
guidelines must be followed:
The interface must not be used beyond its rated voltage range.
The interface must be installed in a UL Listed junction box.
The interface must be installed with conduit in accordance with the National Electrical
Code.

Front Panel Features and Cabling

CAUTION: Do not remove the faceplate screws, (a), while the interface is attached
6
or the detached interface may fall down inside the wall or mounting.
6 9
7
1
10
1
MONITOR
H. SHIFT
2
INPUT
NO MONITOR
3
1
MONITOR
AUDIO
MIN/MAX
RGB 460xi
1
7
8
1
4 5
RGB 460xi
1
2
NO MONITOR
3
MONITOR
1
6 7
MONITOR
INPUT
AUDIO
1
H. SHIFT
MIN/MAX
RGB 468xi
1
MONITOR
2
NO MONITOR
3
1
MONITOR
AUDIO
4
INPUT
H. SHIFT
MIN/MAX
8
5
VIDEO S-VIDEO
L/MONOR
RGB 464xi
11
1
AUDIO
RGB 464xi
NOTE: The RGB 468 Mxi (not pictured) is
functionally identical to the RGB 468xi (at
left) except that it fits in a 3-gang box and provides four mini-AAPs (MAAPs).
12
13
5
4
1
8
RGB 468xi
14
1
2
3
MONITOR
MONITOR
1
6
MONITOR
INPUT
NO
PC AUDIO
4
5
H. SHIFT
MIN/MAX
8
1
7
RGB 468xi AKM UK
1
14
RGB 468xi AKM UK
Figure 2. RGB 460 Series Front Panel Features
RGB 460 Series • Installation and Operation 4
Faceplate screws — These screws secure the faceplate to the rest of the interface.
Tip (+)
Sleeve ( )
Sleeve ( )
Ring (-)
Tip (+)
Audio Plugs.eps
RCA Connector
3.5 mm Stereo Plug Connector (balanced)
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
a
CAUTION: Do not remove these faceplate screws while the interface is attached
to the wall or the detached interface may fall down inside the wall.
Power and signal LED — This LED lights:
b
Yellow to indicate the interface is receiving power.
Green to indicate the interface is receiving power and that an active sync
signal is present at the input.
NOTE: If the input signal has sync on green, the LED will not change from
yellow to green.
Monitor switch (video input termination) — Select one of the following video input
c
impedance selections to provide the best picture:
No Monitor
(75 ohms)
Monitor
(high impedance)
Audio input connector — Plug a 3.5 mm stereo plug
d
into this jack for unbalanced audio input. Wire the
male plug as shown on the right.
Computer input connector — Attach a cable from
e
the computer to the interface via this female 15-pin HD
connector.
Buffered local monitor output connector — Attach
f
a cable from a local monitor to this female 15-pin HD connector.
Horizontal shift control knob (H. Shift) — While viewing the displayed image, rotate
g
this control to move the image to the right or left on the screen. The Min/Max LED (h)
flashes red whenever the minimum or maximum limit of this control is reached.
NOTE: When active, DDSP disables the horizontal shifting control.
Min or Max LED — This LED blinks red momentarily whenever the minimum or
h
maximum limits of the horizontal shift control (g) have been reached. Turning the horizontal shift control knob in the same direction after the limit has been reached
causes the LED to continually blink.
Composite video connector (RGB 464xi) — This female RCA-to-BNC type connector
i
provides pass-through capability for composite video input.
If a local monitor is not connected or if the picture is too bright or blooming (unterminated).
If a local monitor is connected, a laptop breakout cable is used, or if the picture is too dark.
S-video pass-through connector (RGB 464xi ) — Connect an S-video source to this
j
4-pin mini DIN pass-through connector.
RGB 460 Series • Installation and Operation 5
RCA audio connectors (RGB 464xi ) — Connect
#4-40 Nut w/ Captive
k l
Tip (+)
the left audio signal cable to the white RCA connector (k – L/Mono), and the right audio signal cable to the red RCA connector (l – R) for unbalanced stereo audio
pass-through input. Wire the RCA plugs as shown at
right.
Sleeve ( )
NOTE: When a mono audio signal is applied to the L/Mono input, the same
signal is output to both left and right audio outputs.
Network connector (RGB 464xi ) — Connect a computer to this RJ-45 female
m
connector for pass-through to a network.
Opening for architectural adapter plates (RGB 468xi ) — The RGB 468xi accepts
n
up to four optional standard architectural adapter plates (AAPs) attached here (up to
three on the RGB 468xi AKM UK). The RGB 468 Mxi can accept up to four optional mini
architectural adapter plates (MAAPs) attached here. The adapter plates come in a variety of audio/video connector configurations.
Washer
AAP Module
(not included)
H. SHIFT
MONITOR
MIN/MAX
INPUT
NO MONITOR
MONITOR
RGB 468
AUDIO
RGB 468 Mxi
WITH ADSP
TM
NO MONITOR
MONITOR
INPUT
MONITOR
AUDIO
H. SHIFT
MIN/MAX
RGB 468
RGB 468xi
WITH ADSP
TM
Figure 3. AAP and MAAP Mounting
Mounting Screws
MAAP Module (not included)
#4 - 40
Hex Screws
NOTE: The AAPs for the RGB 468xi mount from the rear using #4-40 nuts.
The MAAPs for the RGB 468 Mxi mount from the front using #4-40 hex
screws.
Blank plates (two single space and one double space) are included with the interface
to cover unused spaces. Adapter plates must be ordered separately (see “AAP/MAAP
Availability” on page 17). They must also be attached to the faceplate and cabled
before the interface is installed in the wall or furniture. The screws needed for installing the MAAP adapter plates are supplied, or built into the plates (AAPs). Nuts are supplied for AAP mounting.
To attach an AAP or MAAP:
1. Remove the blank plate or plates from the interface by unscrewing the hex screws
(MAAPs) or removing the nuts (AAPs) that fasten the plates to the faceplate.
2. Attach the adapter plate to the faceplate with the provided hex screws (MAAPs) or
captive washers and #4-40 nuts (AAPs).
3. Attach the output cables to the rear connectors of the adapter plates. Soldering
will be required for some connectors. Attach foil and braided shields to ground connections.
RGB 460 Series • Installation and Operation 6

Rear Panel Features and Cabling

6
6
7
7
8
8
4
9
9
Figure 4. RGB 464xi Interface, Rear Panel
DIP switches — This bank of DIP switches, shown below, controls sync on green
a
output, composite sync output, DDSP, serration pulse output, vertical sync pulse width, and composite sync routing. Moving a switch up sets it "On" and moving it down sets it "Off". In the illustration below, switch 7 is shown in the “On” position.
2
1
5
4
3
4
Closed / On
7
6
8
2
2
3
3
5
51
5
Open / Off
Figure 5. DIP Switch Bank
NOTE: The default for all DIP switches, except for switch 7, is Off (down).
1 — Sync on green
Off — The interface outputs separate horizontal and vertical sync (on the H
and V connectors) for RGBHV.
On — The interface outputs sync on green (RGsB).
2 — Composite sync — This switch controls composite sync output.
Off — The interface outputs RGBHV or RGsB video.
On — The interface outputs combined horizontal and vertical sync for RGBS.
3 — DDSP (Digital Display Sync Processing) — This feature may be necessary for
digital display devices such as LCD, DLP, and plasma displays. ADSP is the default. If the image is not displayed properly after other options such as serration pulse (4) and vertical sync pulse width (5) have been explored, set this switch to On.
Off — The interface performs sync processing operations, such as centering,
with ADSP.
On — The interface uses DDSP.
NOTE: DDSP disables the horizontal shifting control.
RGB 460 Series • Installation and Operation 7
4 — Serration pulse — Many LCD, DLP projectors and plasma displays must have
serration pulses removed from the sync signal in order to display the image properly. Flagging or bending at the top of the video image is a sign the serration pulses should be removed.
Off — The interface does not output serration pulses.
On — The interface outputs serration pulses in the vertical sync interval.
5 — Vertical sync pulse width — Try adjusting the output vertical sync pulse width if
no picture appears, the picture cuts in and out, or the picture is scrambled.
Off — The vertical sync pulse is wide.
On — The vertical sync pulse is narrow.
NOTE: Also try switching from ADSP to DDSP, as explained in the
description for DIP switch 3 on the previous page.
6 — Negative sync — This switch controls sync polarity.
Off — Output sync polarity follows (is the same as) input polarity.
On — Both the horizontal and the vertical sync signals are forced to
negative polarity on output.
7 and 8 — Composite sync routing — These switches work together to route local
monitor signals for Macintosh 13 inch monitors and all other Macintosh and
VGA-type monitors.
NOTE: To be valid, these switches must be set so that one is Off and the
other is On. If both are set to On or both Off, composite sync routing will not function.
7 (On), 8 (Off) — Sync routing to 15-pin HD local monitor for all Macintosh
(non-13 inch) and VGA monitors (default).
7 (Off), 8 (On) — Sync routing to 15-pin HD local monitor for a Macintosh
13 inch monitor.
RGB video output connectors — Attach coaxial cables from the interface to the
b
display device via these female BNC connectors. The BNCs are on red, green, blue,
black, and yellow pigtail wires secured to the interface by the tie wraps.
Output R G B H V RGBHV Red Green Blue Black Yellow
RGBS Red Green Blue Black
RGsB Red Green Blue
RGB 460 Series • Installation and Operation 8
Gain switch — To compensate for cable resistance and capacitance, set this switch to
Power
Do not tin the wires!
c
select the level of video gain that yields the sharpest picture.
Normal (bottom position) Unity gain (no signal boost).
Medium (middle position) Mid-level peaking and gain.
Maximum (top position) Maximum amount of peaking and gain.
(Select this for use with longer cables.)
NOTE: When the signal cable between the interface and the output device is
shorter than approximately 125 feet, and the gain switch is set to medium or maximum, the image may be overcompensated. If the edges of the image seem to exceed their boundaries, or if thin lines and sharp edges look thick and fuzzy, try changing the gain/peaking setting. The gain switch will not be accessible after installation, so adjust the gain before placing the interface into a wall or furniture.
Power connector — Connect a 9 – 24 VDC power supply to this 3.5 mm, 2-pole, direct
d
insertion captive screw connector. Wire the connector as shown below. Polarity is not
important.
+ or – – or +
(5 mm) MAX.
9 – 24 VDC
Figure 6. Power Connector Wiring
CAUTION: Always use a power supply supplied by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification
and may cause damage to the supply and the end product. Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS (Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
Unless otherwise stated, the AC/DC adapters are not suitable for use in
air handling spaces or in wall cavities. The power supply is to be located
within the same vicinity as the Extron A/V processing equipment in an
ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk.
The installation must always be in accordance with the applicable
provisions of National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to building structure or similar structure.
NOTES: The length of the exposed wires in the stripping process is critical. The ideal
length is 3/16 inches (5 mm). Any longer and the exposed wires may touch,
causing a short circuit between them. Any shorter and the wires can be easily pulled out even if tightly fastened by the captive screws.
Do not tin the wires. Tinned wire does not hold its shape and can become loose over time.
RGB 460 Series • Installation and Operation 9
Audio output connector — Insert wires into and tighten the screws on this 3.5 mm,
Do not tin the wires!
e
5-pole, direct insertion captive screw connector for unbalanced or balanced audio
output. Wire the connector as shown here.
CAUTION: For unbalanced stereo output, connect the sleeves to the ground
contact.
DO NOT connect the sleeves to the negative (–) contacts.
Figure 7. Audio Output Wiring
NOTE: The following items f, g, h, and i are features of the 464xi interface only.
Composite video pass-through BNC connector — A male BNC connector attaches
f
here.
S-video pass-through 4-pin mini DIN connector — A male 4-pin mini DIN connector
g
attaches here.
Balanced active audio output connector — Insert wires into and tighten the screws
h
on this 3.5 mm, 5-pole, direct insertion captive screw connector for balanced active
audio output. Wire the connector as shown above.
Network pass-through RJ-45 connector — If this connector is not required, a blank
i
cover is supplied to fill the opening.

Euro Channel and Floor Box Versions

The RGB 460xi and RGB 468xi are available in Euro Channel (EC) versions, the RGB 460xi is available in two floor box models (MK and FSR), and the RGB 468xi AKM UK is designed for
Ackermann floor boxes, see “Accessories” on page 17.
The front and rear panel features, cabling requirements, and testing/troubleshooting procedures are identical to the descriptions shown in this section for the wall box models.
For installation instructions, see the RGB 460xi Series installation guide that addresses the
specific requirements.
NO GROUND HERE
Tip
Sleeve (s)
NO GROUND HERE
Tip
Unbalanced
Stereo Output
RL
Ring
Tip
Sleeve (s)
Ring
Tip
Balanced
Stereo Output
RL
RGB 460 Series • Installation and Operation 10

Mounting Adapter Plates (AAPs or MAAPs)

#4-40 Nut w/ Captive
Washer
AAP Module (not included)
Mounting Screws
H. SHIFT
MIN/MAX
TM
RGB 468xi
INPUT
MONITOR
AUDIO
RGB 468
WITH ADSP
MONITOR
NO MONITOR
All AAPs and MAAPs should be mounted before the interface is installed in a wall or
furniture. Each AAP has standoffs (screws built into the rear panel) and nuts, which can
be used to secure the AAP to the interface. MAAPs are mounted from the front using hex screws.
1. Insert the AAP or MAAP standoffs into the screw holes in the interface.
2. Using the provided #4-40 nuts (standard AAPs) or the provided #4-40 hex screws
(MAAPs), secure the AAP or MAAP to the interface.
Figure 8. Mounting an Adapter Plate
3. Repeat steps 1 and 2 to mount other AAPs or MAAPs. Cover any openings in the
interface with blank AAP or MAAP plates.
4. Be sure to include the AAP and MAAP connectors as part of the installation pretest
before final installation of the interface.
For additional information about interface installation, refer to the appropriate installation
guide available on the Website at www.extron.com.
or
H. SHIFT
MONITOR
MIN/MAX
INPUT
MONITOR
AUDIO
NO MONITOR
RGB 468 Mxi
RGB 468
Mounting Screws
MAAP Module
TM
WITH ADSP
(not included)
Hex Screws
#4 - 40
RGB 460 Series • Installation and Operation 11

Pre-installation Testing

Before installing the interface into the wall, furniture, or floor box, test the system to verify
the connections and settings are correct.
1. Apply power to the interface. The power LED on the interface lights to indicate the
interface is receiving power.
2. Power up and check all connected devices and the interface controls for proper
function.

Troubleshooting

If the power LED does not light, first check the wiring at both the interface and the power
supply, and then ensure the power supply is connected to a power source.
If the power LED lights but a connected device does not function properly follow the
instructions below.
If the image does not appear or there is no sound:
1. Make sure that all connected devices are powered on.
2. Ensure the connectors are wired correctly at both ends of the cables. Audio cables must
be wired for an unbalanced stereo input signal and for a balanced or an unbalanced stereo output signal, see “Rear Panel Features and Cabling” on page 7.
3. If the input is from a laptop computer and no picture appears, use a laptop breakout
cable for the input connection. Check the computer user guide or contact Extron to
determine if special commands are required to output video to the external video port. Also, many laptop screens shut off when the external video port is active.
4. Call the Extron S3 Sales and Technical Support Hotline if the image still does not
appear or there is no sound.

Interface Mounting

If the image is not displayed correctly:
1. If the picture is too bright or dark, or if the edges of the image seem to exceed their
boundaries, or if thin lines and sharp edges look thick and fuzzy, change the gain setting, see “Gain Switch” on page 9 for more details.
2. If the picture appears and is stable, but has ghosting or blooming, verify the video input
is properly terminated. If the problem is not resolved by changing the termination, try using a different input cable. Poor quality or damaged cable can cause ghosting or blooming.
3. If the picture still is not displayed correctly, call the Extron S3 Sales and Technical
Support Hotline.
If the interface does not respond to horizontal shifting
If the picture does not move on screen when the horizontal shift control knob is rotated, DDSP may be active. Set the DDSP DIP switch to Off, see “Rear Panel Features and
Cabling” on page 7.
Once the system has been cabled and tested, the interface can be installed in the wall, furniture, or floor box. To mount the interface, refer to the installation guide for the specific mounting.
RGB 460 Series • Installation and Operation 12

Reference Information

The following reference section contains product specifications, replacement parts numbers and AAP and MAAP architectural plate order details.
Specifications
Ordering Information
Mounting Adapter Plates (AAPs or MAAPs)

Specifications

Video
Gain ............................................... Unity (0.7 V), 15% with 3 dB peaking (0.8 V), 30% with 6 dB peaking (0.9 V)
Bandwidth ..................................... 300 MHz (-3 dB)
Video input and loop through
Number/signal type ........................ 1 analog RGBHV, RGBS, RGsB
Connectors .................................... 1 female 15-pin HD buffered input connector
1 female 15-pin HD local monitor loop through connector
Nominal level ................................. 0.7 Vp-p for RGB
Minimum/maximum levels .............. Analog: 0.3 V to 1.45 Vp-p with no offset at unity gain
Impedance ..................................... 75 ohms or Hi Z, switchable (set to 75 ohms if no local monitor is connected)
Horizontal frequency ...................... 15 kHz to 150 kHz (optimum: 15 kHz to 62 kHz)
Vertical frequency ........................... 30 Hz to 170 Hz
Return loss ..................................... <-30 dB @ 5 MHz
Video output
Number/signal type ........................ 1 analog RGBHV, RGBS, RGsB
Connectors .................................... 5 female BNC on 2" to 2.5" cables
Nominal level ................................. 0.7 Vp-p for RGB
Minimum/maximum levels .............. Analog: 0.7 V to 0.9 Vp-p (switch selectable) with peaking and 0.7 Vp-p input
Impedance ..................................... 75 ohms
Return loss ..................................... -30 dB @ 5 MHz
Sync
Input type ...................................... Autodetect RGBHV, RGBS, RGsB (accepts RGsB but does not strip from video)
Output type ................................... RGBHV: at all times
RGBS: switch selectable RGsB: switch selectable or pass-through
Input level ...................................... 2.0 V to 5.5 Vp-p with +0.2 VDC offset max.
Output level ................................... 4.0 V to 5.0 Vp-p, unterminated
Input impedance ............................ 510 ohms
Output impedance ......................... 75 ohms
Max. propagation delay .................. 52 ns
Max. rise/fall time ........................... 2.5 ns
Polarity ........................................... Positive or negative
RGB 460 Series • Reference Information 13
Audio — all models
Gain ............................................... Unbalanced output: 0 dB; balanced output: +6 dB
Response ........................................ 20 Hz to 20 kHz, ±0.5 dB
THD + Noise ................................... 0.03% @1 kHz, 0.3% @ 20 kHz at nominal level
S/N ................................................. >90 dB at maximum output (14 dBu), balanced (unweighted)
Stereo channel separation .............. >90 dB @ 1 kHz to 20 kHz
Audio input — RGB 464xi
Number/signal type ........................ 2 stereo, unbalanced, 20 Hz to 20 kHz
Connectors .................................... Ch. 1: 3.5 mm female stereo jack (2 channel), unbalanced; tip (L), ring (R),
sleeve (ground) Ch. 2: 2 RCA female jacks
Impedance ..................................... >5k ohms unbalanced, DC coupled
Nominal level ................................. -10 dBV (316 mV)
Maximum level ............................... +8.5 dBu (unbalanced) at 1% THD+N
Audio input — RGB 460xi, RGB 460xi EC, RGB 460xi FSR, RGB 468Mxi, RGB 468xi, RGB 468xi AKM
Number/signal type ........................ 1 stereo, unbalanced, 20 Hz to 20 kHz
Connectors .................................... 3.5 mm female stereo jack (2 channel), unbalanced; tip (L), ring (R),
sleeve (ground)
Impedance ..................................... >5k ohms unbalanced, DC coupled
Nominal level ................................. -10 dBV (316 mV)
Maximum level ............................... +8.5 dBu (unbalanced) at 1% THD+N
Audio output— RGB 464xi
Number/signal type ........................ 2 buffered, stereo (2 channel), balanced/unbalanced
Connectors .................................... (2) 3.5 mm captive screw connectors, 5 pole
Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ...................................... ±0.1 dB channel to channel
Maximum level (600 ohm) .............. +14 dBm, balanced at 1% THD+N
Audio output — RGB 460xi, RGB 460xi EC, RGB 460xi FSR, RGB 468Mxi, RGB 468xi, RGB 468xi AKM
Number/signal type ........................ 1 buffered, stereo (2 channel), balanced/unbalanced
Connectors .................................... 3.5 mm captive screw connector, 5 pole
Impedance ..................................... 50 ohms unbalanced,100 ohms balanced
Gain error ...................................... ±0.1 dB channel to channel
Maximum level (600 ohm) .............. +14 dBm, balanced at 1% THD+N
NOTE: 0 dBu = 0.775 V, 0 dBV = 1 V, 0 dBV 2 dBu.
General
Power ............................................ Supplied by an included 12 VDC, 1 A external power supply
External power supply .................... 100 VAC to 240 VAC, 50-60 Hz, external; to 9 to 12 VDC, 0.2 A, regulated
Power input requirements .............. 12 VDC, 0.2 A (minimum)
Temperature/humidity .................... Storage: -40 to 158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32° to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling .......................................... Convection, no vents
Mounting
Floor box mount
RGB 460/464/468xi SC models
Steel City AFM floor box mountable
RGB 460xi MK ................... MK box mountable
RGB 468xi AKM ................. Ackerman UK oor box mountable
All other models ...................... Wall or furniture mountable
RGB 460 Series • Reference Information 14
Enclosure type ................................ Metal
Enclosure dimensions
RGB 460xi faceplate ................ 4.5" H x 4.6" W x 0.1" D (2 gang)
(11.4 cm H x 11.7 cm W x 0.3 cm D)
RGB 460xi MK faceplate .......... 3.4" H x 5.7" W x 0.1" D
(8.6 cm H x 14.5 cm W x 0.3 cm D)
RGB 460xi FSR faceplate .......... 4.5" H x 3.5" W x 0.1" D
(11.4 cm H x 9.0 cm W x 0.3 cm D)
RGB 464xi/RGB 468Mxi faceplate
4.5" H x 6.4" W x 0.1" D (3 gang) (11.4 cm H x 16.3 cm W x 0.3 cm D)
RGB 468xi faceplate ................ 4.5" H x 8.3" W x 0.1" D (4 gang)
(11.4 cm H x 21.2 cm W x 0.3 cm D)
RGB 468xi AKM faceplate ........ 3.0" H x 8.1" W x 0.6" D
(7.6 cm H x 20.6 cm W x 1.5 cm D)
RGB 460xi EC faceplates .......... 3.2" H x 4.4" W x 0.1" D
(8.0 cm H x 11.2 cm W x 0.3 cm D)
RGB 460xi SC-AFM2 faceplate . 2.9" H x 3.5" W x 0.1" D
(7.4 cm H x 8.9 cm W x 0.3 cm D)
RGB 464xi SC-AFM6 faceplate . 2.9" H x 8.9" W x 0.1" D
(7.4 cm H x 22.6 cm W x 0.3 cm D)
Interface enclosure for all models
2.7" H x 3.3" W x 1.0" D (6.9 cm H x 8.4 cm W x 2.8 cm D)
(Depth excludes front panel connectors and controls.)
Enclosure dimensions
SC-AFM8 adapter plate ........... 4.4" x H x 9.4" W x 0.1" D
(11.2 cm H x 23.9 cm W x 0.3 cm D)
Product weight
RGB 460xi SC-AFM2, RGB 460xi FSR
0.5 lbs (0.3 kg)
RGB 464xi SC-AFM6 ................ 0.8 lbs (0.4 kg)
SC-AFM8 ................................. 0.6 lbs (0.3 kg)
RGB 460xi ............................... 0.5 lbs (0.2 kg)
RGB 460xi MK ......................... 0.5 lbs (0.2 kg)
RGB 464xi, RGB 468xi, RGB 468 Mxi
0.7 lbs (0.3 kg)
EC models ............................... 0.7 lbs (0.3 kg)
RGB 468xi AKM ....................... 0.8 lbs (0.4 kg)
Shipping weight
RGB 468xi AKM ....................... 2 lbs (1 kg)
All other models ...................... 3 lbs (2 kg)
Vibration ........................................ ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety ...................................... CE, c-UL, UL
EMI/EMC ................................. CE, C-tick, FCC Class A, ICES, VCCI
MTBF ............................................. 30,000 hours
Warranty ........................................ 3 years parts and labor
NOTE: All nominal levels are at ±10%.
NOTE: Specifications are subject to change without notice.
RGB 460 Series • Reference Information 15

Ordering Information

RGB 460xi Part numbers
Interface 60-373-02 (black), -03 (white), -05 (RAL9010 white)
2-gang mud ring kit 70-519-22 (black), -23 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
RGB 460xi FSR, RGB 460xi SC-AFM2 Part numbers
Interface
2-gang mud ring kit 70-519-22 (black), -23 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
RGB 460xi MK Part numbers
Interface 60-467-01 (black, white), -05 (RAL9010 white) 4-gang mud ring kit 70-519-42 (black), -43 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
RGB 460xi EC Part numbers
Interface 60-373-50 (RAL9010 white) Power supply kit 70-775-01 (12 VDC, 1 A external)
RGB 464xi Part numbers
Interface
3-gang mud ring kit 70-519-32 (black), -33 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
60-373-40 (FSR) 60-463-01 (Steel City)
60-374-02 (black), -03 (white),
-05 (RAL9010 white)
RGB 468xi Part numbers
Interface
4-gang mud ring kit 70-519-42 (black), -43 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
RGB 468xi AKM Part numbers
Interface 60-626-02 (black) Power supply 70-775-01 (12 VDC, 1 A external)
Blank AAP, single (1)
Blank AAP, double (1) 70-090-12 (black), -22 (white)
RGB 468 Mxi Part numbers
Interface
3-gang mud ring kit 70-519-32 (black), -33 (white) Power supply kit 70-775-01 (12 VDC, 1 A external)
60-375-02 (black), -03 (white)
-05 (RAL9010 white)
70-090-01 (gray), -11 (black),
-21 (white), -51 (RAL9010 white)
60-591-02 (black), -03 (white),
-05 (RAL9010 white)
RGB 460 Series • Reference Information 16

Accessories

NOTE: A Setup Guide (part number 68-542-50) ships with all RGB 460xi Series interface
models. Depending on mounting, one of the following installation guides ship with the interface:
Description Part Number
RGB 400xi Series MK Installation Guide 68-636-02 RGB 400xi Series Wall Box Installation Guide 68-636-03 RGB 460xi Steel City Box Installation Guide 68-636-04 RGB 460xi/472xi FSR Installation Guide 68-636-05 AKM UK Series Installation Guide 68-904-01
Wall/Junction boxes Part number
JB 225 two-gang J-box, 2.5 inches deep 980084 JB 325 three-gang J-box, 2.5 inches deep 980083 JB 425 four-gang J-box, 2.5 inches deep 980097
Audio connector Part number
3.5 mm Mini Stereo-HQ/10 (quantity 10) 100-331-01

Cables

Male-to-male Molded VGA cables Part number
VGA M-M MD/6, 6 feet (1.8 m) 26-238-01 VGA-A M-M MD/3 (with audio), 3 feet (90 cm) 26-490-01 VGA-A M-M MD/6 (with audio), 6 feet (1.8m) 26-490-02 VGA-A M-M MD/12 (with audio), 12 foot (3.6 m) 26-490-03
BNC Series Mini High Resolution Cables (non-plenum)
MHR-5 BNC/3, 3 feet (90 cm) 26-260-15 MHR-5 BNC/6, 6 feet (1.8 m) 26-260-01 MHR-5 BNC/12, 12 feet (3.6 m) 26-260-02 MHR-5 BNC/25, 25 feet (7.6 m) 26-260-03 MHR-5 BNC/35, 35 feet (10.6 m) 26-260-17 MHR-5 BNC/50, 50 feet (15.2 m) 26-260-04 MHR-5 BNC/75, 75 feet (22.8 m) 26-260-16 MHR-5 BNC/100, 100 feet (30.4 m) 26-260-05
Part number
RGB 460 Series • Reference Information 17
Blank Plate (no connector)
Blank Plate (no connector)
BNC Series Mini High Resolution Cables (plenum)
MHR-5P BNC/3, 3 feet (90 cm) 26-378-01 MHR-5P BNC/6, 6 feet (1.8 m) 26-378-02 MHR-5P BNC/12, 12 feet (3.6 m) 26-378-03 MHR-5P BNC/25, 25 feet (7.6 m) 26-378-04 MHR-5P BNC/35, 35 feet (10.6 m) 26-378-12 MHR-5P BNC/50, 50 feet (15.2 m) 26-378-05 MHR-5P BNC/75, 75 feet (22.8 m) 26-378-06 MHR-5P BNC/100, 100 feet (30.4 m) 26-378-07

AAP and MAAP Modules

A variety of Architectural Adapter Plates (AAPs) and Mini Architectural Adapter
Plates (MAAPs) for pass-through connections are available for the RGB 468xi and RGB 468 Mxi interfaces.
The RGB 468xi can accommodate up to four single-space AAPs (up to three with the RGB 468xi AKM UK), and the RGB 468 Mxi can accommodate up to four single-space
MAAPs.
Both single- and double-space AAPs and MAAPs, and AAP and MAAP blanks are available. Refer to the current Extron catalog or Website for a complete listing.
Part number
Single Space
Two BNC
Three BNC
Two RCA to Solder Cups
Three RCA to Solder Cups
Two S-video
Double Space
Five BNC (Double)
Two RJ-11
One 9-pin D Gender Changer
Figure 9. Sample Architectural Adapter Plates
RGB 460 Series • Reference Information 18
Extron® Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America, and Central America:
Extron Electronics 1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe Hanzeboulevard 10 3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363
Japan:
Extron Electronics, Japan Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
China:
Extron China 686 Ronghua Road
Songjiang District Shanghai 201611 China
Middle East:
Extron Middle East Dubai Airport Free Zone F12, PO Box 293666 United Arab Emirates, Dubai
Singapore
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: (714) 491-1500 Europe: 31.33.453.4040 Asia: 65.6383.4400 Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or tness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.
Extron USA - West Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500 +1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794 +1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040 +31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400 +65.6383.4664 FAX
Extron Japan
+81.3.3511.7655 +81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568 +86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800 +971.4.2991880 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Loading...