Extron electronics RGB 400 Series, RGB 402, RGB 404, RGB 406, RGB 408 User Manual

...

Download

Page 1

User’s Manual

EXTRON ELECTRONICS/RGB SYSTEMS, INC. 1230 South Lewis Street, Anaheim, CA 92805

800.633.9876 714.491.1500 FAX 714.491.1517 USA

EXTRON ELECTRONICS, EUROPE Beeldschermweg 6C, 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands

EXTRON ELECTRONICS, ASIA 41B Kreta Ayer Road, Singapore 089003 +65.226.0015 FAX +65.226.0019 Singapore

EXTRON ELECTRONIC INFORMATION E

XTRON

WEB™: www.extron.com

XTRON

FAX™: 714.491.0192

24-hour access — worldwide!

Mountable Interfaces

68-364-01

Printed in the USA

RGB 400 Series

Page 2

Precautions

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating

instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future

reference.

Follow Warnings • Follow all warnings and instructions marked on the

equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not

recommended by the equipment manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source

indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all

power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to

be stepped on or pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no user-

serviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are

provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced.

Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de

sécurité et d’exploitation avant d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de

pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et

consignes marqués sur le matériel ou présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni

d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation

indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,

déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de

manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-

maintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,

ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la

batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll den Benutzer auf wichtige Anleitungen zur Bedienung und Wartung (Instandhaltung) in der Dokumentation hinweisen, die im Lieferumfang dieses Gerätes enthalten ist.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,

sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Sicherheitsanleitungen sollten

aufbewahrt werden, damit Sie später darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und

Anleitungen auf dem Gerät oder in der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,

die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene

Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Stift oder Kontakt ist für einen Erdschluß, und stellt eine Sicherheitsfunktion dar und sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,

sollten Sie alle Netzkabel aus der Rückseite des Gerätes oder aus dem DesktopStrommodul (falls dies möglich ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht

im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem

Servicepersonal durchgeführt werden. Im Inneren des Gerätes sind keine Teile enthalten, die vom Benutzer gewartet werden können. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst zu warten, da beim Öffnen oder Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse

aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.

Ersetzen Sie nur durch die gleiche oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgung der verbrauchten Batterien bitte gemäß den Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de

operación y seguridad, antes de usar el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad

para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones

marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no

sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo

de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la

acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se

deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal

calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/ mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,

es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición

incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.

Instrucciones de seguridad • Español

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

Extron Electronics 1230 South Lewis Street Anaheim, CA 92805, U.S.A.

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification to the product.

If it has been determined that the product is defective, please call Extron and ask for an Applications Engineer at (714) 491-1500 to receive an RA# (Return Authorization number). This will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state, and that some provisions of this warranty may not apply to you.

Page 3

iRGB 400 Series Table of Contents

Chapter 1 • Introduction ..........................................................1-1

About this Manual ................................................................1-2

About the RGB 400 Series Interfaces .......................... 1-2

Features ...................................................................................... 1-2

RGB 400 Series features.........................................................1-2

Additional RGB 402 and RGB 404 features .......................... 1-2

Additional RGB 406 and RGB 408 features .......................... 1-2

Chapter 2 • Installation and Operation......................... 2-1

Installation Overview..........................................................2-2

Installation and Operation Instructions....................2-3

Determining installation location ........................................2-3

Preparing the installation site, installing the wall box ....... 2-4

Front and rear panel (circuit board) features ...................... 2-6

RGB 400 front and rear features...........................................2-6

RGB 406 front and rear features...........................................2-7

RGB 402 front and rear features...........................................2-8

RGB 404 front and rear features.........................................2-10

RGB 408 front and rear features.........................................2-12

Setting DIP switches and jumpers.......................................2-14

DIP switches ..................................................................... 2-14

Jumpers ........................................................................... 2-14

Attaching adapter plates (RGB 408) ................................... 2-15

Cabling and connections ..................................................... 2-16

Attaching cables to pass-through connectors ................... 2-16

Connecting shields ............................................................... 2-17

Connecting audio cables — RGB 404 ................................. 2-18

Connecting audio cables — RGB 406, RGB 408 ................. 2-20

Connecting input cables and video output cables ............ 2-20

Attaching power cables.......................................................2-20

Using installation cable ....................................................... 2-21

Pre-installation testing/troubleshooting ............................ 2-21

Mounting the interface to the wall box ............................ 2-23

Application diagrams .......................................................... 2-25

Appendix A • Specifications................................................. A-1

Appendix B • Templates............................................................B-1

RGB 400 and RGB 406 Cut-out Template ................... B-2

RGB 402 and RGB 404 Cut-out Template ................... B-3

RGB 408 Cut-out Template ................................................ B-4

Table of Contents

Page 4

RGB 400 Series Table of Contents

Table of Contents, cont’d

RGB 400 Series

Chapter One

Introduction

About This Manual

About The RGB 400 Series Interfaces

Features

Appendix C • Dimensions........................................................C-1

RGB 400 Panel Dimensions ...............................................C-2

RGB 402 Panel Dimensions ...............................................C-3

RGB 404 Panel Dimensions ...............................................C-4

RGB 406 Panel Dimensions ...............................................C-5

RGB 408 Panel Dimensions ...............................................C-6

RGB 408 Panel Dimension Details.................................C-7

Appendix D • Accessories and Part Numbers .......... D-1

Interfaces and Included Parts ........................................ D-2

Accessories and Connectors ........................................... D-2

Cables ......................................................................................... D-3

Optional Adapter Plates ................................................... D-4

68-364-01 C

Printed in the USA

10 99

Page 5

RGB 400 Series Introduction

Introduction, cont’d

RGB 400 Series

Chapter Two

Installation and Operation

Installation Overview

Installation and Operation Instructions

Introduction

About This Manual

This manual contains information about the RGB 400 Series interfaces and on how to operate and configure them.

About The RGB 400 Series Interfaces

The RGB 400 Series are 300 MHz (-3dB) bandwidth, analog computer-video interfaces that can be mounted in walls or furniture. The RGB 400 and RGB 406 are two-gang wall plate size, the RGB 402 and RGB 404 are three-gang size, and the RGB 408 is four-gang size. All are available with black, white, or gray panels.

Features

RGB 400 Series features

Horizontal centering control — Shifts the image horizontally . Level control — Adjusts the image brightness. Peaking control — Adjusts the image sharpness. Sync output options — Six BNC connectors allow separate

horizontal, vertical and composite sync outputs. Sync-on-green (SOG) is output only if SOG is input.

Digital Display Sync Processing™ (DDSP™) — Sync is

output in its original state to ensure compatibility with digital display products.

75 ohm video termination switch — For applications

where a local computer monitor is not being used.

Additional RGB 402 and RGB 404 features

The RGB 402 and RGB 404 offer the following features in addition to the RGB 400 Series features listed above:

Composite video pass-through RCA connector S-video pass-through 4-pin mini DIN connector Network pass-through (RJ-45 connector) Left and right audio pass-through RCA connectors

(RGB 402 only)

Two 2-channel audio outputs (unbalanced in, balanced

out) on RCA and PC stereo connectors (RGB 404 only)

Additional RGB 406 and RGB 408 features

The RGB 406 and RGB 408 offer these features in addition to the RGB 400 Series features listed above:

Two channels of audio (unbalanced in, balanced out) Optional pass-through adapter plates (RGB 408 only)

1-2

Page 6

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

2-3

Installation and Operation Instructions

Determining installation location

Take cabling and power availability and the location of wall studs into consideration when selecting an installation site. You may need to install the cables in the wall, furniture or conduits before installing the interface. Choose a location that will allow cable runs without interference, preferably next to a 2” x 4” wall stud.

The RGB 400 Series interfaces each consist of a front panel with an attached circuit board. They are typically installed in standard 2-, 3- or 4-gang, 2.5-inch deep electrical wall boxes. A metal wall box (provided by Extron) is preferred, but a plastic box (or no wall box at all) can be used as long as it conforms to local code restrictions and the interface’s size requirements. If a wall box is used, it must be attached to wall studs within the wall.

The drawing below illustrates the typical depth required to accommodate the maximum bend of high resolution (SHR) coaxial and miniature coaxial cables inside a wall box.

SHR Coax Cable

Approximately 3.3"

Approximately 2.5"

Circuit Board

Front Panel

Mini-Coax Cable

Minimum installation depth needed for maximum coaxial cable bend

Cut-out (rough-in) templates and dimensional drawings are provided in the appendices of this manual.

Installation and Operation

2-2

Installation Overview

To install and set up an RGB 400 Series interface, follow these basic steps:

Determine the installation location.

Prepare the site for installation. Use the supplied template to mark the rough-in cutout, then cut out the wallboard or wood.

Set the DIP (dual in-line package) switches and jumpers. These items will be inaccessible after

installation.

For the RGB 408, attach optional adapter plates, and attach output cables to the back sides of the adapter plates.

For all models, connect the wires and cables for power, audio output and pass-through signals.

These items will be inaccessible after installation.

For all models, set the front panel High Z/75 Ohm video termination toggle switch.

Temporarily connect the input cables. Connect any

cables whose signals will be routed through the optional adaptor pass-through plates.

Connect power cables to the input and output devices. Turn on the input and output devices.

The image should now display on screen. If it does not display, or if the picture displays incorrectly, double check and make adjustments to cables, DIP switches and jumpers as needed. Refer to the “Pre-installation testing/troubleshooting” section in this chapter.

Temporarily disconnect the input cables from the front panel of the interface, and disconnect the power from the interface.

Mount the interface in the wall or furniture.

Reconnect the computer video and audio input cables to the interface, apply power, and readjust horizontal centering as needed via the front panel control.

Page 7

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

2-5

Flush with Wall Surface

Screws or Nails

Wall Stud

Wall Box

Attaching the wall box to wall studs

To attach the wall box to wood, use four #8 to # 10 wood or sheet metal screws. A minimum of 1/2 inch (1.25 cm) of screw threads must penetrate the wood. If the wood is a 2 x 4, such as a wall stud, 10-penny or larger nails can be used.

To attach the electrical wall box to metal, use four #8 or #10 sheet metal screws (self-tapping) or #8 or #10 machine bolts with matching nuts.

7. Output cables will usually be out of sight inside a wall, for example. Feed the cables through the wall box “punch-out” holes for connection to the interface. Cable clamps should be used to hold the cables in place for strain relief.

8. Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate shields with heat shrink. Details for typical maximum coaxial cable bend inside a wall box are given on page 2-3.

9. Configure, cable and test the interface before securing the interface to the wall box. Configuration consists of setting circuit board DIP switches and jumpers based on installation requirements. See page 2-14 for more information.

2-4

Preparing the installation site and installing the wall box

Actual-size rough-in templates for each model are provided in Appendix B. If needed, make a 100% size photocopy of the appropriate template to use for installation. Compare the photocopy with the faceplate and wall box to make sure the photocopy size is the same as the equipment.

Use the template as a guide to mark and cut the hole in the wall or furniture through which the interface will be installed. The innermost line represents the opening where material will be removed and the wall box will be installed.

1. Cut out the center portion (up to the guidelines) of the cut-out (rough-in) template.

2. Place the template on the surface where the interface will be installed. Use a soft pencil to mark the guidelines for the opening on the wall/furniture.

3. Cut out the material from the cut-out area with a jigsaw or small hand saw.

4. Check the opening size by inserting the wall box (if used) or the interface (if no wall box is used) into the opening. The wall box will be mounted flush with the outer wall or furniture surface. The box and/or interface should fit easily into the opening.

5. If needed, use a saw, file or sandpaper to enlarge the hole. Smooth the edges of the opening to avoid damage or injury to yourself or the cables during installation.

6. Attach the wall box to the wall stud (2 x 4) with nails or screws, leaving the front edge flush with the wall surface, as shown in the following illustration.

Page 8

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Extron

RGB 406/ RGB 408 Captive

Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V .9V

.7V

.8V

.9V

BGR

RGB 406

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

AUDIO

J10

SW1

J11 J12

J13

1 2 3

67 910 12 1311

FRONT REAR

RGB 406 front and rear features

Auto power LED — If this LED is on, power and sync pulses

are present. If no sync is present, power and this LED turn off.

H. Shift (horizontal shift) control — This controls horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB analog input.

Audio 3.5 mm stereo PC-type connector for unbalanced input — See page 2-12 for an input plug wiring diagram.

High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.

BNC output connectors — These 6 connectors are for video and sync output. Connect the coaxial cables’ BNC connectors as shown on page 2-6 for red, green and blue video output, and either separate horizontal and vertical sync or composite sync.

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

Audio output 3.5 mm, 5-pole captive screw connector — The label below this connector provides a wiring diagram for balanced audio output.

SW1 DIP switches — 1. ON = Removes serration pulses.

2. ON = Enables Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wires — Splice these wires to a 12 to 24VAC or VDC power source.

2-7

Front and rear panel (circuit board) features

RGB 400 front and rear features

J10

RGB 406/ RGB 408

Captive Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V .9V

.7V

.8V

.9V

BGR

Extron

RGB 400

SW1

J11 J12

J13

INPUT

H. SHIFT

HIGH Z

75 Ohm

AUTO POWER

123 4 567810 119

FRONT REAR

BGR

2-6

Auto power LED — If this LED (light-emitting diode) is on,

power and video sync pulses are present. If no sync pulse is

present,

power and this LED turn off.

H. Shift (horizontal shift) control — This controls horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB analog input.

High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.

BNC output connectors — These 6 connectors are for video and sync output. Connect the coaxial cables’ BNC connectors as

shown here for red, green and blue video output, and either separate horizontal and vertical sync or composite sync.

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

SW1 DIP switches — 1. ON = Remove serration pulses.

2. ON = Enable Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wires — Splice these wires to a 12 to 24VAC or VDC power source.

Page 9

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

SW1 DIP switches —

1. ON = Removes serration pulses.

2. ON = Enables Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Composite video pass-through RCA connector — If you remove this connector , replace it with the 0.31” diam. plastic plug that is shipped with the RGB 402.

S-video pass-through 4-pin mini DIN connector — If you remove this connector, replace it with the 0.50” diam. plastic plug that is supplied with the RGB 402.

BNC output connectors — These 6 connectors are for video and sync output. Connect the coax cables’ BNC connectors as shown on page 2-6 for red, green and blue video output, and either separate horizontal and vertical sync or composite sync.

Twisted pair wires — Splice these wires to a 12 to 24VAC or VDC power source.

J10

RGB 406/ RGB 408

Captive Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V .9V

.7V

.8V

.9V

BGR

Black

RedYellow

Green

1314 15

REAR

789 11 12

2-9

Auto power LED — If active sync pulses are present, power and this LED turn on. If not, power and this LED turn off.

H. Shift (horizontal shift) control — This controls the horizontal centering. If output is SOG, or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB analog input.

High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.

Left and right audio channel pass-through RCA connectors — The input to the RCA connectors

should be wired as shown here.

Tip

Sleeve ( )

If you remove these connectors, replace them with the 0.31 inch diameter plastic plugs supplied with the RGB 402.

Network pass-through RJ-45 connector

RGB 402 front and rear features

VIDEO

S-VIDEO

AUDIO

NETWORK

Extron

RGB 402

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

13 14

2 3

FRONT

2-8

Page 10

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Pin assignment label for the audio output captive screw connector (item 9) — Audio output wiring is discussed in

the cabling section of this chapter.

Audio output captive screw connector — Use this connector for the balanced output from both audio channels (1 and 2). See the wiring diagram label (item 8) and the cabling section in this manual for wiring instructions.

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

SW1 DIP switches — 1. ON = Removes serration pulses.

2. ON = Enables Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on

the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wires — Splice these wires to a 12 to 24VAC or VDC power source.

Composite video pass-through RCA connector—If unused, this connector can be replaced with a 0.31” diam. plug.

S-video pass-through 4-pin mini DIN connector — This connector can be replaced with a 0.50” diam. plug.

BNC output connectors — These 6 connectors are for video and sync output. Connect the coax cables’ BNC connectors

as shown here for red, green and blue video output, and either separate horizontal and vertical sync or composite sync.

BGR

RGB 406/ RGB 408 Captive

Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V .9V

.7V

.8V

.9V

BGR

CH1L CH1R CH1R

12345678910

Signal

Ground

CH1L

& CH1R outputs are

generated from RCA inputs.

CH2L

& CH2R outputs are

generated from 3.5 mm inputs.

RCA

3.5 mm

REV. A 79-08

33-323-01

J10

SW1

J11 J12

J13

95687

1718 19

10 11 12 14 1513

Black

RedYellow

Green

REAR

2-11

RGB 404 front and rear features

VIDEO

S-VIDEO

NETWORK

Extron

RGB 404

A U D I O

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

567

17 18

2 3 4

FRONT

Auto power LED — If active sync pulses are present, power and this LED turn on. If not, power and this LED turn off.

H. Shift (horizontal shift) control — This controls the horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB input.

High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.

PC type 3.5 mm stereo audio input connector — This connector is for unbalanced input to audio channel 2. Wire the input plug as shown here.

Tip (+) Sleeve (GND)

Tip (L, +)

Ring (R, -)

Sleeve (GND)

Left and right audio channel RCA connectors — These connectors are for unbalanced input to audio channel 1. Wire the input plugs as shown below.

Tip

Sleeve ( )

Network pass-through RJ-45 connector

2-10

Page 11

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

2-13

BNC output connectors — These 6 connectors are for video and sync output. Connect the coaxial cables’ BNC connectors as shown here for red, green and blue

video output, and either separate horizontal and vertical sync or composite sync.

J13 jumper — Pin 1 = +5V, pin 2 = -5V, pin 3 = ground.

Audio output 3.5 mm, 5-pole captive screw connector

— The label below this connector provides a wiring diagram for balanced audio output.

SW1 DIP switches —

1. ON = Remove serration pulses.

2. ON = Enable Digital Display Sync Processing (DDSP).

J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board.

J9 green gain/peaking jumper

J8 red gain/peaking jumper

Circuit board — Only key components are shown here.

Twisted-pair wire — Splice these wires to a 12 to 24VAC or VDC power source.

BGR

RGB 408 front and rear features

Auto power LED — If this LED is on, power and video sync pulses are present. If no sync is present, power and this LED turn off.

H. Shift (horizontal shift) control — This controls horizontal centering. If output is SOG or if DIP SW1-2 (DDSP) is set to On, the horizontal shift control is disabled.

Input — This 9-pin D-sub male connector is for RGB analog input.

Audio input 3.5 mm stereo PC-type connector for unbalanced input — Wire the PC audio input plug as shown here.

Tip (+) Sleeve (GND)

Tip (L, +)

Ring (R, -)

Sleeve (GND)

High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.

Architectural adapter plates installation bay — Up to four adapter plates for pass-through audio/video connections can be attached at one time to the interface. See the “Attaching adapter plates” section in this chapter for installation instructions.

2-12

AUDIO

INPUT

AUTO POWER

H. SHIFT

HIGH Z

75 Ohm

Extron

RGB 40 8

1234 65

FRONT

RGB 406/ RGB 408

Captive

Screw

Connector

J13

33-398-01 B 08 99

J10

1 = +5V 20 mA max. 2 = –5V 20 mA max. 3 = Ground

SW1

321

1. ON = Remove serration pulses.

2. ON = Digital display sync.

.8V .9V

.7V

.8V

.9V

BGR

J10

SW1

J11 J12

J13

78 1011 13 14

REAR

Page 12

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Attaching adapter plates (RGB 408)

The RGB 408 can have up to 4 optional adapter plates. The adapter plates allow for a variety of types of pass-through audio and/or video connectors to be added to the interface’s front panel faceplate.

Blank plates (two single-height and one double-height plate) are included with the RGB 408 to cover unused spaces. Other adapter plates must be ordered separately. They also must be attached to the faceplate and cabled before the interface is installed in the wall or furniture. The screws needed for installing the adapter plates are built into the plates, so no additional screws will be needed.

1. Remove the blank plates from the interface by

unscrewing the nuts that fasten the plates to the faceplate.

2. Insert the adapter plate screws through the holes in

the faceplate. Attach the adapter plates to the faceplate with the provided captive washers and #4-40 nuts. See the illustration “Installing optional adapter plates” on the next page.

3. Attach the output cables to the connectors on the back

side of the adapter plates. Several adapter plates require conductors to be soldered to the connectors. Attach foil and braided shields to ground connections.

Each red (J8), green (J9) and blue (J10) jumper can be set to one of three positions to provide unity gain (0.7 volts p-p),

0.8 volts p-p, or 0.9 volts p-p output. Select the setting that yields the best image display. Use the diagram on the product label (shown below) as a guide to setting the output gain/peaking for each color.

J10

.8V .9V

.7V

.8V .9V

.7V

.8V

.9V

RGB 400 Series gain/peaking jumpers

0.7V — Use this for short cable runs (under 125 feet).

0.8V — Use this for long cable runs for all frequencies.

0.9V — Use this setting for long cable runs and high frequency video signals.

2-15

Setting DIP switches and jumpers

DIP switches and jumpers must be set and tested before the interface is secured into the wall box, wall or furniture.

DIP switches

DIP switch module SW1 contains two DIP switches (SW1-1 and SW1-2). The module is located on the circuit board on

the back of the interface, as shown on pages 2-6, 2-7, 2-9, 2-11 and 2-13. In these illustrations, the On position is to the left.

Different video projectors may have slightly different sync requirements. Use the DIP switches on the interface to make the interface’s output compatible with the projector.

DIP switch 1 (SW1-1) controls serration pulse output.

ON = No serration pulses will be output in the

composite sync signal.

OFF = Serration pulses will be output.

DIP switch 2 (SW1-2) controls sync processing.

ON = Digital Display Sync Processing (DDSP) will be

used. This may be required in order to obtain a stable picture on some digital display devices. When DDSP is on, horizontal shift (centering) is disabled.

OFF = DDSP will not be used.

Jumpers

Video signals passing through long cable runs (over 125 feet) or through poor quality cables can decrease in strength, creating signal loss. The longer the cable, the higher the video level and the greater the peaking that will be needed to compensate for the loss.

The gain/peaking adjustment jumpers are located on the circuit board on the back of the interface, as shown in the rear features sections of this manual. To configure the jumpers, use pliers to pull the jumper shunt off the pins, then place the jumper on the appropriate pins.

Make sure the interface is disconnected from the power source before configuring jumpers.

Changing jumper settings

SW1

2-14

Page 13

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Cabling RCA connectors

For composite video, solder the center conductor of a coaxial cable to the central solder cup of the RCA connector. Solder the cable’s shield to the grounded grounding tab. See the leftmost and center illustrations below.

Attaching coaxial and twisted-pair cables to RCA connectors

For audio, solder the signal wire of a shielded twisted-pair cable to the central solder cup of the RCA connector. Solder the ground wire to the grounded tab, as shown above at right.

Connecting shields

Multiconductor cables such as Extron’s Install Plenum bulk cable contain several braided and foil shields. At the interface end of the cable, the outer braided and foil shields should be connected to the grounded metal wall box (or to a grounding wire if a metal wall box is not used). The wires that make up the braided shield can be unbraided, then twisted together to form a large, multistrand wire that can be folded back under the wall box cable clamp or attached to the metal wall box with a screw. See the illustration below.

To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp. Both the braided and foil shields should be connected to an equipment ground at the other end of the cable.

Grounding outer braided and foil shields

Shield

Center Conductor

RCA ConnectorCoaxial Cable Twisted Pair

Central Solder Cup

Grounding Tab

Metal Wall Box

Screw

Braided Shield

Install Cable

Foil Shield

Cable Clamp

2-17

#4-40 Nut w/Captive Washer

RGB 408 (Up to 4 Plates)

Adapter Plate

AUTO POWER

m H

AUDIO

RGB 408

Installing optional adapter plates

Cabling and connections

Attaching cables to pass-through connectors

The RGB 402 and RGB 404 provide pass-through connectors for composite video, S-video, RJ-45 network and, for the RGB 402 only, two-channel stereo audio. These connectors are mounted on the faceplate. The RJ-45 cable can be plugged in from the back. Coaxial cables and/or twisted pair wires must be soldered to the back side of the S-video and RCA connectors, as described in this section.

Optional adapter plates with various types and combinations of pass-through audio and video connectors are available for the RGB 408. Many adapter plates also require cables and wires to be soldered to the rear connectors.

Cabling S-video connectors

The illustration below identifies the S-video connector signal leads. For the RGB 402/404, splice and solder the

four wires from this connector to user-supplied coaxial cables. Insulate the soldered connections to prevent shorts. You can also use the connector’s shield tabs for chrominance and luminance ground tie points.

S-video connector wiring diagram

Chrominance

signal

Luminance signal

Chrominance

ground

Luminance ground

Red

Yellow

Green

Black

Shield tab

2-16

Page 14

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

signal. For example, the input signals from the left side of channel one (CH1L) are output as CH1L+ and CH1L-. The following illustration shows the audio inputs and outputs and how to wire the audio connectors.

Captive Screw

Connector

Base

Circuit Board

MaleFemale

GND

Channel 1

Channel 2

Channel 1

from Audio L, R

RCA

Connectors

Channel 2

from PC

3.5mm

Connector

Wiring RGB 404 audio connectors

To wire the audio output captive screw connector, follow these steps:

1. Prepare the wires for insertion into the connector by trimming off 3/16 inch of insulation.

2. Following the wiring diagram found on the label on the back of the faceplate or in this manual, insert the wires one at a time into the connector.

3. Tighten the wire clamp in the connector by turning the appropriate screw clockwise. Do not overtighten the screw. Avoid touching circuit board components with the ends of the wires. See the illustration below.

RGB 404 RGB 406 and RGB 408

Base

Ground/Shield

Circuit Board Circuit Board

Wiring audio output captive screw connectors

4. The cable shields should be connected to either pins 3 and 8 (RGB 404) or pin 3 (RGB 406/408) of the audio

2-19

If shielded twisted-pair wires are used for audio output for the RGB 404, RGB 406 or RGB 408, the shields should be connected to either pin 3 (RGB 406/408) or pins 3 and 8 (RGB 404) of the audio output captive screw connector. Twist the wires from the braided shield together to form a multi-strand wire, then insert it into the receptacle side of the captive screw connector. See the “Wiring audio output captive screw connectors” illustration on the next page.

Twisted-pair shields are not used for most other RGB 400 Series applications, even when twisted-pair wires are used. For those other applications, twist the shields together, and fold them back under the wall box cable clamp or attach them to the grounded wall box with a screw.

To prevent short circuits, unused shielded twisted-pair wires and exposed cable shields (braided or foil) must be insulated with electrical tape or heat shrink, and secured.

Connect coaxial cables’ shields to a ground through the individual connectors (BNC, S-video or RCA).

Connecting audio cables — RGB 404

The RGB 404 creates two 2-channel, balanced audio outputs from two unbalanced inputs.

• Audio channel one (CH1) consists of unbalanced input

on two RCA input connectors (one each for left and

right input), and balanced output on pins 1 – 5 of the 10-pole audio captive screw connector on the rear of the circuit board. Wire the RCA input plugs as shown at left.

• Audio channel two (CH2) consists of unbalanced left and

right input from the single PC-type 3.5 mm audio plug, and balanced output on pins 6 – 10 of the 10pole captive screw connector on the rear of the circuit board. Wire the stereo PC input plug as shown here:

Tip (+) Sleeve (GND)

Tip (L, +)

Ring (R, -)

Sleeve (GND)

The audio signals are converted from unbalanced to balanced signals as they pass through the RGB 404. As a result, two output signals are produced for each input

2-18

Tip

Sleeve ( )

Page 15

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Pre-installation testing/troubleshooting

Before installing the interface into the wall or furniture, test the system to make sure that the connections and interface settings are correct.

Turn on the input device(s) (computer, audio device) and output device(s) (projector and/or monitor, speakers). The image should now appear on the screen, and, for all models except the RGB 400, sound should be audible.

If the image does not appear or there is no sound

1. Ensure that all devices are plugged in.

2. Make sure that each device is receiving power. The interface’s Auto power indicator LED will light if the interface is receiving power and an active sync signal.

Using installation cable

Extron’s Install Plenum bulk cable (shown here) is ideal for mountable interfaces such as the RGB 400 Series models.

Double Shielded Foil and Copper Strand

Center Conductor (Stranded)

Sheath

Plenum Jacket, Double Shielded

Foil and Copper Strand

Polyethylene Foam

Four Sets of Twisted Pair (Stranded), Wire Braid Shield

Six Mini, High-resolution

Coaxial Conductors

17-Conductor Install Plenum Cable

Three 20-gauge Wires

Below is an example of how the cable can be used.

Red & Black Twisted Pair

White & Black Twisted Pair

20 Gauge Violet

Yellow Mini-Coax

White Mini-Coax

20 Gauge Gray

Red

Yellow

Green

Red

Black

RGB 402 Rear

Black Mini-Coax Blue Mini-Coax Green Mini-Coax

Red Mini-Coax

Shield to Black

Shield to Green

Using installation cable with an RGB 402

2-21

output captive screw connector. See “Connecting shields” earlier in this chapter for details.

Connecting audio cables — RGB 406, RGB 408

Each RGB 406 or RGB 408 accepts an unbalanced audio input from a front panel 3.5 mm PC-type stereo connector, and it outputs two channels of balanced audio on a 3.5 mm, 5-pole captive screw connector on the rear of the circuit

board. Follow the steps listed for the RGB 404 for inserting wires into captive screw connectors. Use the label on the rear of the faceplate (excerpted here) as a wiring guide.

Connecting input cables and video output cables

With appropriate cables, connect the computer and, for all models except the RGB 400, audio device(s) to the interface via the front panel input connectors. Connect all the devices for pass-through input (network, composite video, S-video and/or other inputs) via front panel or front adapter plate connectors.

Determine what computer-video format the display device requires: separate horizontal and vertical sync (RGBHV), composite sync (RGBS), or sync on green (RGsB or SOG). No matter what format the computer outputs to the interface, the output from the interface to the display device can be RGBHV or RGBS. If the video format input to the interface is RGsB (SOG), RGsB can be output to the display device; otherwise only RGBHV and RGBS are available as output options.

Connect the display device to the interface using coaxial cables. Attach the cable’s BNC connectors to the appropriate rear panel BNC connectors on the interface based on the video format required by the display device.

Attaching power cables

Each RGB 400 Series interface requires an external voltage source of 12 to 24 volts AC or DC (250 mA maximum, 5 W). The interfaces are supplied with a power cord of twistedpair wire soldered to the circuit board.

1. Splice these wires to the cord of a user-supplied power source. Polarity is not important, even if the power source supplies DC voltage. Extron offers an optional external power supply. See Appendix D for the part number.

2. Solder and insulate the connections.

12345

2-20

Page 16

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Mounting the interface to the wall box

Once the system has been cabled and tested, the interface can be installed in the wall or furniture.

1. Remove power from the interface and input and output devices by disconnecting the power cords from the power supply.

2. Detach the input cables from the front panel.

3. For the RGB 408 only, install the EMI strips. To maintain proper grounding connections between

the interface faceplate and the wall box, adequate contact between the faceplate and wall box must be ensured. Installing the supplied EMI (electromagnetic interference) strips will ensure the proper contact and maintain the ground. To install the strips, do the following:

a. Peel off the protective, papery coating from the

back of an EMI strip.

b. Apply the EMI strip to the center of the upper lip

of the 4-gang wall box, pressing firmly to ensure contact. See the illustration below.

c. Repeat steps 1 and 2 to install the other EMI con-

ductive strip onto the lower lip of the wall box.

EMI Strips

4-gang Wall Box

EMI Strip

Remove Adhesive Backing

RGB 408

Installing EMI strips on the wall box

2-23

the situation, either the pass-through connector or any cable that was part of the installation but not used for this test may be the source of the problem. If this test does not produce an image or sound, the problem may lie with an input device or an output device.

3. Check the cabling and the audio connector wiring, and make adjustments as needed.

4. Verify that the High Z/75 Ohm video input termination toggle switch on the front panel has been set correctly.

5. For digital display devices (including LCD, DLP and plasma devices), try turning DDSP on or off using the rear panel SW1-2 DIP switch.

6. Call Extron’s customer support hotline if needed.

If the image does not display correctly

1. If the output image looks too green, the computer may be sending video with sync on green (SOG), and the display device may not be configured to handle SOG signals. The RGB 400 Series interfaces do not strip sync from the video input signals.

2. If the picture bends or flags at the top of the screen, set the serration pulse DIP switch (SW1-1) to Off.

3. For a display device that experiences intermittent glitches, try turning DDSP on or off using the rear panel SW1-2 DIP switch.

4. If the picture “hangs off” the edges of the screen, adjust the H. Shift horizontal centering control.

5. If the edges of the image seem to exceed their boundaries or if thin lines and sharp edges look thick and fuzzy, try changing the gain/peaking jumper (J10, J9, J8) settings. If the image is too bright, decrease the gain/peaking level.

6. If the image appears and is stable, but it has ghosting or blooming, check the High Z/75 Ohm video input termination. If changing the termination doesn’t solve the problem, try using a different input cable.

7. If the image still does not display correctly, call Extron’s customer support hotline.

If no image or sound results from pass-through connections

1. Make sure each input device is connected to the correct pass-through connector, which in turn is connected to the appropriate output device.

2. Ensure that each connector is properly wired and grounded, and that each device is powered on.

3. If there still is no image or sound, try cabling the input device directly to the output device. If that resolves

2-22

Page 17

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

Application diagrams

Below are examples of typical system installations that incorporate RGB 400 series interfaces. Many other configurations are possible. Extron offers a variety of laptop and monitor breakout cables for easy connection of PCs, Macintosh, Sun or SGI computers.

VIDEO

S-VIDEO

NETWORK

Extron

RGB 404

A U D

Video Cassette Player

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

Laptop Computer

LBC Cable

RJ45 Network Cable

An RGB 404 application featuring a laptop and network and S-video pass-through connections

Extron

RGB 406

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

AUDIO

SVGA Compatible

Computer w/ Audio

MBC Cable Audio Cable

A typical RGB 406 application

2-24

4. For all models, carefully place the interface through the opening in the wall or furniture and into the wall box (if one is used). Take care not to damage the cables.

5. Mount the interface faceplate to the wall box with the provided machine screws (as shown below), or attach the interface directly to the furniture with wood or metal screws.

Mounting the interface to the wall box

6. Reconnect the input cables to the interface via the front panel connectors.

7. Reconnect the power cables and restore power to the equipment.

Install Cable

Cable Clamp

RGB 404

A U D

-V

2-25

Page 18

RGB 400 Series Installation and Operation

Installation and Operation, cont’d

RGB 400 Series

Appendix A

Specifications

2-26

Page 19

RGB 400 Series Specifications

Specifications, cont’d

A-3

Audio input — RGB 402

Number/type .............................. 1 stereo, unbalanced (pass-through)

Connectors.................................... 2 RCA female jacks

Audio input — RGB 404

Number/type .............................. 2 stereo, unbalanced; 1.0Vrms (+4dBu),

20 Hz to 20 kHz

Connectors..................................... Ch. 1 ........... 2 RCA female jacks

Ch. 2........... 3.5 mm stereo female jack

(2 channel), unbalanced; tip (L), ring (R),

sleeve (ground)

Impedance .................................... 10 kohms, DC coupled

Minimum level ............................ 100mV

Maximum level............................ +8.5dBu

Audio input — RGB 406 and RGB 408

Number/type .............................. 1 stereo, unbalanced; 1.0Vrms (+4dBu),

20 Hz to 20 kHz

Connectors.................................... 3.5 mm stereo female jack (2 channel),

unbalanced;

tip (L), ring (R), sleeve (ground)

Impedance .................................... 10 kohms, DC coupled

Minimum level ............................ 100mV

Maximum level............................ +8.5dBu

Audio throughput — RGB 404 (channels 1 and 2), RGB 406 and RGB 408

Gain ............................................... Unbalanced 0dB, balanced +6dB

Response ....................................... ±0.5dB @ 20 Hz to 20 kHz

THD + Noise ................................ 0.03% @1 kHz, 0.3% @ 20 kHz at rated

maximum output drive

S/N ................................................ >90dB, output 14dBu, balanced

Stereo channel separation .......... >95dB @ 1 kHz to 20 kHz

Audio output — RGB 402

Number/type .............................. 1 stereo, unbalanced

Connectors.................................... 1 pair solder cups

Specifications

A-2

These specifications apply to all models unless otherwise noted.

Video input

Number/type .............................. 1 analog RGBHV, RGBS, RGsB

Connectors.................................... 1 9-pin male D connector for MBC/LBC

cable or buffer

Nominal level(s) .......................... Analog — 0.3V to 1.45V p-p

Impedance .................................... 75 ohms or HI Z, switchable (set to

75 ohms if no local monitor is connected)

Horizontal frequency ................. 15 kHz to 150 kHz (optimum 15 kHz to 62

kHz)

Vertical frequency ....................... 30 Hz to 170 Hz

Return loss .................................... -30dB @ 5 MHz

Video throughput

Gain ............................................... Unity (0.7V), 15% with 3dB peaking

(0.8V), 30% with 6dB peaking (0.9V)

Bandwidth .................................... 300 MHz (-3dB)

Video output

Number/type/format ................ 1 analog RGBHV, RGBS, RGsB

Connectors.................................... 6 BNC female

Nominal level .............................. Analog 0.7V p-p, 0.8V p-p, or 0.9V p-p

(internal jumper-selectable) w/peaking

Impedance .................................... 75 ohms

Return loss .................................... -30dB @ 5 MHz

Sync

Input type ..................................... Autodetect RGBHV, RGBS, RGsB

(accepts RGsB but does not strip from

video)

Output type .................................. RGBHV at all times

RGBS at all times

RGsB only when input is RGsB

Input level .................................... 2.0V to 5.5V p-p with

+0.2VDC offset

max.

Output level ................................. 4.0V to 5.0V p-p

Input impedance ......................... 10 kohms

Output impedance ...................... 75 ohms

Max propagation delay .............. 50 nS

Max rise/fall time ....................... 2.5 nS

Polarity.......................................... Positive or negative

Page 20

RGB 400 Series Specifications

Specifications, cont’d

Enclosure dimensions (RGB 402 and RGB 404)

Plate .................................... 4.50” H x 6.40” W

(11.43 cm H x 16.26 cm W)

Box ...................................... 3.75" H x 5.3" W x 2.5" D

(9.5 cm H x 14.2 cm W x 6.35 cm D) 3-gang

Interface ............................. 2.8" H x 5.3" W x 2.5” D

(7.1 cm H x 13.5 cm W x 6.4 cm D) (depth is given with an HR cable attached)

Enclosure dimensions (RGB 408)

Plate .................................... 4.50” H x 8.33” W

(11.43 cm H x 21.15 cm W)

Box ...................................... 3.75" H x 7.38" W x 2.50" D

(9.50 cm H x 18.73 cm W x 6.35 cm D) 4-gang

Interface ............................. 2.8" H x 3.5" W x 2.5” D

(7.1 cm H x 8.9 cm W x 6.4 cm D) (depth is given for the circuit board with an HR cable attached)

Shipping weight (all models).... 3 lbs (1.4 kg)

Vibration ....................................... NSTA 1A in carton

(National Safe Transit Association)

Approvals ..................................... UL, CE, FCC Class A

MTBF ............................................. 30,000 hours

Warranty ....................................... 2 years parts and labor

Specifications are subject to change without notice.

A-5

Audio output — RGB 404 (channels 1 and 2)

Number/type .............................. 2 buffered, stereo (2 channel),

balanced/unbalanced

Connectors.................................... 3.5 mm captive screw terminal,

5 conductor

Impedance .................................... 50 ohms unbalanced, 100 ohms balanced

Gain error ..................................... ±0.1dB channel to channel

Drive (600 ohm) ........................... +14dBu, balanced at stated %THD+N

Audio output — RGB 406 and RGB 408

Number/type .............................. 1 buffered, stereo (2 channel),

balanced/unbalanced

Connectors.................................... 3.5 mm captive screw terminal,

5 conductor

Impedance .................................... 50 ohms, unbalanced, 100 ohms balanced

Gain error ..................................... ±0.1dB channel to channel

Drive (600 ohm) ........................... +14dBu, balanced at stated %THD+N

General

Power ............................................ 12 to 24VAC or VDC, 0.25 A, 5 Watts,

external (Order the power supply

separately.)

Temperature/humidity ............. Storage -40° to +158°F (-40° to +70°C) /

10% to 90%, non condensing

Operating +32° to +122°F (0° to +50°C) /

10% to 90%, non condensing

Rack mount .................................. No, but wall or furniture mountable

Enclosure type ............................. Metal

Enclosure dimensions (RGB 400 and RGB 406)

Plate .................................... 4.50” H x 4 . 6 0” W (11.43 cm H x 11.68 cm W)

Box ...................................... 3.75" H x 3.75" W x 2.5" D

(9.5 cm H x 9.5 cm W x 6.35 cm D) 2-gang

Interface ............................. 2.8" H x 3.5" W x 2.5” D

(7.1 cm H x 8.9 cm W x 6.4 cm D)

(depth is given for the circuit board with

an HR cable attached)

A-4

Page 21

RGB 400 Series Specifications

Specifications, cont’d

RGB 400 Series

Appendix B

Templates

RGB 400 and RGB 406 Cut-out Template RGB 402 and RGB 404 Cut-out Template

RGB 408 Cut-out Template

A-6

Page 22

RGB 400 Series Templates

Templates, cont’d

B-3

RGB 402 and RGB 404 Cut-out Template

Use this template for cutting a hole in a wall or furniture for the 3-gang size electrical box for an RGB 402 or RGB 404.

The light gray area represents the lay out of the

electrical box (3.75"H x 5.60"W) against the rear

of the RGB 402 or RGB 404 front panel.

The dashed line indicates the cut-out area

(3.95"H x 5.80"W) for installing

the electrical wall box.

T o install the interface

without

a wall box,

use the cut-out area (3.00"H)

indicated by the dotted line.

B-2

All the templates in this section are actual size. Also, they all include the recommended 0.1” (0.25 cm) clearance on all sides of the electrical wall box to allow room for the raised areas surrounding the knockouts.

The dashed line in each template indicates the cut-out area for installing a wall box. If you plan to install the interface without a wall box, use the smaller cut-out area indicated by the dotted lines.

RGB 400 and RGB 406 Cut-out Template

Use this template as a guide for cutting a hole in a wall or furniture for the 2-gang size electrical box in order to install an RGB 400 or RGB 406.

The light gray area represents the lay out of the

electrical box (3.75"H x 3.75"W) against the rear

of the RGB 400 or RGB 406 front panel.

The dashed line indicates the cut-out

area (3.95"H x 3.95"W) for installing

the electrical wall box.

T o install the interface

without

a wall box,

use the cut-out area (3.00"H)

indicated by the dotted line.

Templates

Page 23

RGB 400 Series Templates

Templates, cont’d

RGB 400 Series

Appendix C

Dimensions

RGB 400 Panel Dimensions RGB 402 Panel Dimensions RGB 404 Panel Dimensions RGB 406 Panel Dimensions RGB 408 Panel Dimensions

RGB 408 Panel Dimension Details

B-4

The light gray area represents the layout of the electrical box (3.75"H x 7.38"W)

against the rear of the RGB 408 front panel.

The dashed line indicates the cut-out area (3.95"H x 7.58"W)

for installing the electrical wall box.

To install the interface

without

a wall box,

use the cut-out area (3.00"H)

indicated by the dotted line.

RGB 408 Cut-out Template

Use this template for cutting a hole in a wall or

furniture for the electrical box and pass-through

connections for the 4-gang size RGB 408.

Page 24

RGB 400 Series Dimensions

Dimensions, cont’d

C-3

RGB 402 Panel Dimensions

Extron

INPUT

HIGH Z

Ohm

AUTO POWER

RGB

402

DETAIL B

DETAIL A

HAND SAND TO

0.06" RADIUS

AROUND TOP EDGES.

DETAIL C

DETAIL A

DETAIL B

SCALE: 2/1

DETAIL C

(VIEWED FROM BACK SIDE)

STANDOFFS:

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

VIDEO

S-VIDEO

AUDIO

H. SHIFT

C-2

The diagrams in this appendix have been reduced to fit on the pages. All dimensions are given in inches. The symbol “ø” indicates a diameter.

RGB 400 Panel Dimensions

Extron

RGB

400

INPUT

H. SHIFT

HIGH Z

75 Ohm

AUTO POWER

HAND SAND T O 0.06" RADIUS

AROUND THE TOP OF

THESE EDGES.

DETAIL A

DETAIL B

STANDOFFS:

REQ'D

ø.156 THRU

WITH C'SINK ø.290 x 82˚

ON NEAR SIDE (4 PLACES MARKED ' ' )

ø.213 THRU

(2 PLACES MARKED 'b')

ø.125 THRU

ø.230 THRU

DETAIL A

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

Dimensions

Page 25

RGB 400 Series Dimensions

Dimensions, cont’d

C-5

Extron

RGB

406

INPUT

H. SHIFT

HIGH Z

75 Ohm

AUTO POWER

DETAIL C

HAND SAND T O 0.06" RADIUS

AROUND THE TOP OF

THESE EDGES.

DETAIL A

DETAIL B

STANDOFFS:

REQ'D

ø.156 THRU

WITH C'SINK ø.290 x 82˚

ON NEAR SIDE (4 PLACES MARKED ' ' )

ø.213 THRU

(2 PLACES MARKED 'b')

ø.125 THRU

ø.230 THRU

DETAIL A

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

DETAIL B

ø.200

.184

AUDIO

DETAIL C

ø.400

ø.240

THRU

.06

RGB 406 Panel Dimensions

C-4

RGB 404 Panel Dimensions

VIDEO

S- VIDEO

NETWORK

Extron

RGB

404

AUD

INPUT

HIGH Z

75 Ohm

H. SHIFT

AUTO POWER

HAND SAND TO

0.06" RADIUS

AROUND TOP EDGES.

STANDOFFS: 2

REQ'D

ø.213 THRU

(2 PLACES MARKED B)

ø.236 THRU

C'BORE ø.400

x .060 DEEP

ø.156 THRU

C'SINK ø.290 x 82˚

(4 PLACES)

REQ'D

ø.085 THRU

(2 PLACES)

ø.323 THRU

(3 PLACES

MARKED C)

ø.111

(

PLACES MARKED E )

ø.125 THRU

ø.230 THRU

DETAIL A

DETAIL B

SCALE: 2/1

DETAIL C

(VIEWED FROM BACK SIDE)

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

DETAIL B

DETAIL A

DETAIL C

Page 26

RGB 400 Series Dimensions

Dimensions, cont’d

RGB 408 Panel Dimension Details

C-7

0.700

1.050

2.100

2.810

0.350

3.520

2.740

1.760

1.370

1.405

ø 0.170 THRU (8 PLACES)

1.375

2.750

3.000

1.500

R 0.050 (4 PLACES)

DETAIL A

ø.120 THRU, WITH ø.250 C'BORE ON

BOTH SIDES, .040 DEPTH ON THE

NEAR SIDE, AND .020 DEPTH

ON THE FAR SIDE. (2 PLCS.)

DETAIL B

ø.201

.190

DETAIL C

ø.400

ø.240

THRU

.06

.225

.449

4– R .132

.403

DETAIL D

0.040 DEEP RECESS

C-6

RGB 408 Panel Dimensions

AUDIO

AUTO POWER

H. SHIFT

HIGH

Ohm

Extron

RGB 40 8

INPUT

DETAIL C

HAND SAND T O 0.06" RADIUS

AROUND THE TOP OF

THESE EDGES.

DETAIL A

DETAIL B DETAIL D

STANDOFFS:

REQ'D

ø.156 THRU

WITH C'SINK

ø.290 x 82˚ ON NEAR SIDE

(4 PLACES MARKED ' ' )

ø.213 THRU

(2 PLACES MARKED 'b')

ø 0.125 THRU

ø 0.230 THRU

0.000

0.609

1.050

1.055

1.140

1.395

2.175

2.280

3.450

3.891

4.500

0.000

0.744

1.154

1.444

1.929

2.174

3.104

3.844

6.025

6.881

8.325

R 0.250

(4 PLCS)

2.250

Page 27

RGB 400 Series Dimensions

Dimensions, cont’d

RGB 400 Series

Appendix D

Accessories and Part Numbers

Interfaces and Included Parts

Accessories and Connectors

Cables

Optional Adapter Plates

C-8

Page 28

RGB 400 Series Part Numbers and Accessories

Part Numbers and Accessories, cont’d

Cables

Monitor breakout cables Part number

MBC VGA/XGA HR 26-162-01 MBC Mac/Quadra 26-018-02 MBC Sun/Sparc HR 26-424-01 MBC SGI/13W3 HR 26-425-01

Below is a listing of some of the laptop breakout cables and other cables available for use with RGB 400 Series interfaces. A variety of lengths is available for each type of cable. See the Extron product catalog or call Extron’s support hotline for details.

Laptop breakout cables Part number

LBC VGA HR 3’ 26-224-02 LBC VGA HR 6’ 26-224-01 LBC VGA HR 12’ 26-224-03 LBC Mac HR 6’ 26-363-01 LBC Sun HR 6’ (61 kHz) 26-413-01 LBC Sun HR 6’ (71 kHz) 26-413-02 LBC Sun HR 6’ (81 kHz) 26-413-03 LBC Mac/VGA HR 26-394-01

Laptop breakout cables w/audio Part number

LBC VGA HR 3’A 26-441-01 LBC VGA HR 6’A 26-441-02 LBC VGA HR 12’A 26-441-03

LBC Mac HR 6’A 26-442-02 LBC Sun HR 6’A (61 kHz) 26-443-02 LBC Sun HR 6’A (71 kHz) 26-444-02 LBC Sun HR 6’A (81 kHz) 26-445-02

Bulk cables (without connectors) Part number

Bulk SHR-1, 500’ 22-098-02 Bulk SHR-4, 500’ 22-099-02 Bulk SHR-5, 500’ 22-100-02 Bulk BNC 4-500’ HR 22-032-02 Bulk BNC 5-500’ HR 22-020-02 Bulk BNC 5-500’ HRP (plenum) 22-103-02 Bulk 17-conductor Install Plenum, 500’ 22-111-03

D-3

Interfaces and Included Parts

This section lists the interfaces and the main parts that are shipped with each model. All models include:

• this manual, part number 68-364-01,

• one standard cable clamp with two machine screws, and

• four 3/8 inch, flathead screws (for attaching the faceplate).

Interfaces and included parts Part number

RGB 400G (gray faceplate) 60-222-01 RGB 400B (black faceplate) 60-222-02 RGB 400W (white faceplate) 60-222-03

RGB 402G (gray faceplate) 60-231-01 RGB 402B (black faceplate) 60-231-02 RGB 402W (white faceplate) 60-231-03

0.31” diameter plastic plugs (3) *

0.50” diameter plastic plug (1) * RGB 404G (gray faceplate) 60-237-01

RGB 404B (black faceplate) 60-237-02 RGB 404W (white faceplate) 60-237-03

0.31” diameter plastic plug (1) *

0.50” diameter plastic plug (1) *

3.5 mm, 10-pole captive screw connector 10-319-11 RGB 406G (gray faceplate) 60-249-01

RGB 406B (black faceplate) 60-249-02 RGB 406W (white faceplate) 60-249-03

RGB 408G (gray faceplate) 60-307-01 RGB 408B (black faceplate) 60-307-02 RGB 408W (white faceplate) 60-307-03 EMI strips (two, 4-inch) 100-107-01 Blank, single-height adapter plates 70-090-01/-11/-21 Blank, double-height adapter plate 70-090-02/-12/-22

* These plugs can replace unused pass-through connectors.

Accessories and Connectors

Accessories/connectors Part number

12VDC, 1A external power supply

(from 100 to 240 VAC, 50/60 Hz) 70-055-01

3.5 mm, 5-pole captive screw connector 10-319-10 BNC mini-HR crimp connectors (qty. = 50) 100-074-51 BNC SHR crimp connectors (qty. = 50) 100-075-51 BNC bulkhead connectors (qty. = 50)

(for custom wallplates) 100-076-51

D-2

Part Numbers and Accessories

Page 29

RGB 400 Series Part Numbers and Accessories

Part Numbers and Accessories, cont’d

D-5

setalPretpadAlarutcetihcrArotcennoCepyTelgniS

noitpircsedetalpretpadA

etalP

ezis

epytrotcennoctnorF epytrotcennocraeR #traP

yarG kcalB etihW

)elamefotelamef(lerrabCNB21elamefCNBelamefCNB190-0710-11-12-

)elamefotelamef(lerrabCNB31elamefCNBelamefCNB190-0720-21-22-

)elamefotelamef(lerrabCNB52elamefCNBelamefCNB190-0730-31-32-

)elamefotelamef(lerrabCNBotACR21)kcalb/der(elamefACRelamefCNB490-0710-11-12-

)elamefotelamef(lerrabCNBotACR31)kcalb/der(elamefACRelamefCNB490-0720-21-22-

).mefot.mef(lerraboediv-Sotoediv-S21elamefNIDinimnip-4elamefNIDinimnip-4590-0710-11-12-

elamefonohpoerets"¼21elamefonohpoerets"¼ slanimretgulredlos3790-0710-11-12-

elamefoeretsinimmm5.321elamefoeretsinimmm5.3slanimretgulredlos3890-0710-11-12-

)elamefotelamef(54-JR22elamef54-JRelamef54-JR001-0710-11-12-

)elamefotelamef(51-DH11elamefDHnip-51elamefDHnip-51101-0710-11-12-

)elamefotelamef(9-D11elamefDnip-9elamefDnip-9201-0710-11-12-

elamefRLXnip-312elamefRLXnip-3slanimretgulredlos3301-0710-11-12-

)esuom/draobyek(NIDinimnip-621elamefNIDinimnip-6elamefNIDinimnip-6401-0710-11-12-

lanimretwercsevitpacelop5,mm5.311wercsevitpacelop5,mm5.3spucredlos501-0710-11-12-

em-wohsDEL/hctiwserusolctcatnoc1

kcajinimoeretsmm5.3dna

dnahctiwserusolctcatnoc

kcajoeretsinimmm5.3

spucredlos601-0710-11-12-

Pre-cut cables

BNC-5 cables are primarily used for applications that require RGBHV signals. BNC-4 cables are mainly used for RGBS signals. Either can be used to route composite video, S-video or RGB with sync on green. All of these cables come in lengths from 3 feet to 300 feet, and all have male BNC connectors on both ends. The BNC-5 HR cables are also available in a plenum version.

Pre-cut high resolution cables Part number

BNC-4-25’HR (25 feet/7.5 meters) 26-210-04 BNC-4-300’HR (300 feet/90.0 meters) 26-210-53 BNC-5-25’HR (25 feet/7.5 meters) 26-260-03 BNC-5-300’HR (300 feet/90.0 meters) 26-260-14

D-4

Optional Adapter Plates

A variety of optional adapter plates for pass-through connections may be ordered for the RGB 408 interface. The RGB 408 can have up to 4 adapter plates installed in one of the following configurations:

• four adapter plates with a “plate size” of one,

• two adapter plates with a plate size of one and one

adapter plate with a plate size of two,

• or two adapter plates with a plate size of two. The RGB 408 is shipped with two single height blank plates

(part #70-090-01/-11/-21) and one double height blank plate (part #70-090-02/-12/-22).

The tables on the following page list some of the available adapter plates. Contact Extron for a complete list.

2 - BNC

Blank Plate (no connector)

Single Space

Double Space

Blank Plate (no connector)

5 - BNC (Double)

2 - RJ-11

2 - RCA to Solder Cups

3 - RCA to Solder Cups

2 - S-video

1 - D-9 Pass Through Connector

3 - BNC

Architectural adapter plates

Page 30

RGB 400 Series Part Numbers and Accessories

Part Numbers and Accessories, cont’d

D-6

setalPretpadAlarutcetihcrArotcennoCepyTitluM

noitpircsedetalpretpadA

etalP

ezis

tnorF

epytrotcennoc

raeR

epytrotcennoc

#traP yarG

kcalB etihW

elamefACR3dnaelamefoediv-S12

dnaelamefNIDinimnip-4

elamefACR

elamefNIDinimnip-4

elamefACRdna

701-0720-21-22-

dnaelamefCNB1

kcajoeretsinimmm5.31

dnaelamefCNB

kcajoeretsinimmm5.3

dnaelamefCNB

spucredlos3

801-0720-21-22-

D-7

Page 31

RGB 400 Series Part Numbers and Accessories

Part Numbers and Accessories, cont’d

D-8