Extron electronic MTP DA4 User Manual

Power Supply

Output Cord

SECTION A–A

Ridges

Smooth

A A

Captive

Screw

Connector

Tie Wrap

3"
16 (5 mm) Max.

Setup Guide — MTP DA4 and DA8

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4 050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

1234

A/V INPUT

A/V OUTPUTS

5

Pin

1
2
3

6
7
8

4

Wire color

White-green

NOTE If you are using Enhanced

Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.

Green
White-orange

White-blue
Orange
White-brown
Brown

Wire color

T568A T568B

White-orange
Orange
White-green

White-blue
Green
White-brown
Brown

Blue Blue

Insert
TP Wires

Pins:

12345678

1 2 3 4 A

OUTPUT MUTE

0.5A MAX

12V

POWER

+

-

OUTPUT MUTE

1

2

3

4

5

6

7

8

A

INPUT

1 2

3

4

56 78

OUTPUTS

OUTPUT

SHARP

L

R

INPUT VIDEO

12V

0.5a

MAX

MTP R SV A

OUTPUT

SHARP

L R

INPUT

VIDEO

12V

0.5a

MAX

MTP R SV A

OUTPUT

SHARP

LR

INPUT

VIDEO

12V

0.5a

MAX

MTP R SV A

OUTPUT

SHARP

L

R

INPUT

VIDEO

12V

0.5a

MAX

MTP R SV A

INPUT

MTP T SV A RCA

VIDEO

OUTPUT

L R

12V

0.5a
MAX

Flat Panel
Display

Extron
MTP DA8

Mini Twisted Pair
Distribution Amplier

Up To
8 Receivers

Extron
MTP T AV RCA

Twisted Pair
Transmitter

DVD

Extron
MTP R AV

Twisted Pair
Receivers

TP Cable

TP Cable

A

S

A

S

A

S

J9

Disable

Mute

(Default)

or

Enable

Mute

A

S

A

S

A

S

J3

Serial

(Default)

or

Audio

Setup Guide — MTP DA4 and DA8, cont’d

This card provides quick start instructions for an experienced
installer to set up and operate any of the MTP DA
distribution amplifier.

Pre-installation — Jumpers

Refer to the MTP DA Series User’s Guide for more
information.

N The jumpers have no effect when the

DA is part of an MTP CV/SV series,
or VTT001/VTR001 system.

Jumper J3 sets the DA for either audio
(default) or serial data in addition to the RGB
video.
Jumper J9 sets the DA to either always pass
the audio or serial link regardless of the
contact closure mute status (default), or to
mute the audio or serial link when its video
mute function is activated.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MTP DA as required.

Step 2 — Input from the transmitter

Terminate a TP cable as shown at right. Connect
it between an MTP transmitter and the A/V Input
connector.

Operation — Mutes

To mute an output, tie that ouput’s Output Mute pin to ground (_).
To mute all outputs, tie the A pin to ground.

Step 3 — Outputs to the receivers

Terminate up to four or eight TP cables as shown at
right. Connect them between the DA’s A/V Output
port and receivers that are compatible with the
transmitter.

N The input and all outputs should all be

Step 4 — Power

Wire the 2-pole captive screw connector for the included
external 12 VDC power supply as shown at right. Plug it into
the DA.

terminated using the same standard on both
ends of the cables.

Example of a typical MTP DA8 application

68-975-50

Rev. A 01 09