Extron electronic IR 102 User Manual

User’s Manual

www.extron.com

Extron Electronics, USA

1230 South Lewis Street
Anaheim, CA 92805
USA

714.491.1500
Fax [phone]

Extron Electronics, Europe

Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]

© 2006 Extron Electronics. All rights reserved.

Extron Electronics, Asia

135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]

Extron Electronics, Japan

Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax [phone]

Infrared Remote Control

IR 102 Kit

68-663-01 Rev. C

03 06

Precautions

Safety Instructions • English

This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.

This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.

Caution

Read Instructions • Read and understand all safety and operating

instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future

reference.

Follow Warnings • Follow all warnings and instructions marked on the

equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not

recommended by the equipment manufacturer because they may be
hazardous.

Consignes de Sécurité • Français

Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de

sécurité et d’exploitation avant d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afi n de pouvoir

les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et consignes

marqués sur le matériel ou présentés dans la documentation utilisateur.

Eviter les pièces de fi xation • Ne pas utiliser de pièces de fi xation ni d’outils

non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,

sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit

des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und

Anleitungen auf dem Gerät oder in der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,

die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.

Instrucciones de seguridad • Español

Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y

seguridad, antes de usar el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para

futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones marcadas

en el equipo o en la documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no

sean especifi camente recomendados por el fabricante, ya que podrian
implicar riesgos.

Warning

Power sources • This equipment should be operated only from the power source

indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power

cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be

stepped on or pinched by items placed upon or against them.

Servicing • Refer all servicing to qualifi ed service personnel. There are no user-

serviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are

provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly

replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation

indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fi l de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,

déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de

manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-

maintenance par un technicien qualifi é. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afi n d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifi ces • Si le boîtier de l’appareil comporte des fentes ou des orifi ces, ceux-ci

servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.

Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene

Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten

Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im

Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifi ziertem Servicepersonal

durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,

dienen diese zur Vermeidung einer Überhitzung der empfi ndlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt

wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo

de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida

de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben

instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal

califi cado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orifi cios en su caja/alojamiento,

es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición

incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.

FCC Class A Notice

Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:

USA, Canada, South America, Europe, Africa, and the Middle East:
and Central America: Extron Electronics, Europe

Extron Electronics Beeldschermweg 6C
1001 East Ball Road 3821 AH Amersfoort
Anaheim, CA 92805, USA The Netherlands

Asia: Japan:

Extron Electronics, Asia Extron Electronics, Japan
135 Joo Seng Road, #04-01 Kyodo Building
PM Industrial Bldg. 16 Ichibancho
Singapore 368363 Chiyoda-ku, Tokyo 102-0082
Japan

This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non­Extron authorized modifi cation to the product.

If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at [phone] (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fi tness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.

Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.

安全须知 • 中文

这个符号提示用户该设备用户手册中
有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴

露的危险电压，有触电危险。

注意

阅读说明书 • 用 户使 用该 设备 前必 须阅 读并 理

解 所有 安全 和使 用说 明。

保存说明书 • 用户应保存安全说明书以备将来使

用。

遵守警告 • 用户应遵守产品和用户指南上的所有安

全和操作说明。

避免追加 • 不要使用该产品厂商没有推荐的工具或

追加设备，以避免危险。

警告

电源 • 该 设备 只能 使用 产品 上标 明的 电源 。 设备

必 须使 用有 地线 的供 电系 统供 电。 第 三条 线
（ 地线 ）是 安全 设施 ，不 能不 用或 跳过 。

拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后

或桌面电源的电源线，或任何接到市电系统的电源线。

电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没

有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。

通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止

机内敏感元件过热。 不要用任何东西挡住通风孔。

锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与

厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。

i

Table of Contents

Chapter One • Installation and Operation ................... 1-1

About the IR 102 Kit ................................................................. 1-2

Mounting the IR 102 Rx Remote Receiver ......................... 1-2

Rack mounting ....................................................................... 1-2

Furniture mounting ............................................................... 1-4

Projector mounting ................................................................ 1-4

Connecting the Receiver to a Switcher ..............................1-7

Features and Connections ...................................................... 1-8

Installing Batteries in the Remote ..................................... 1-11

Operation ...................................................................................1-11

Working together with a control system ...........................1-11

Appendix A • Specifications, Part Numbers,
Accessories

Specifications ..............................................................................A-2

Included Parts .............................................................................A-3

Accessories ...................................................................................A-3

........................................................................................A-1

All trademarks mentioned in this manual are the properties of their respective owners.

68-663-01 C

03 06

IR 102 Remote Control Kit • Table of Contents

i

Table of Contents, cont’d

IR 102 Remote Control Kit

Chapter One

1

Installation and Operation

About the IR 102 Kit

Mounting the IR 102 Rx Remote Receiver

Connecting the Receiver to a Switcher

Features and Connections

Installing Batteries in the Remote

Operation

ii

IR 102 Remote Control Kit • Table of Contents

IR 102 Remote Control Kit • Installation and Operation

Installation and Operation

IR 102 Remote Control Kit • Installation and Operation

1-2

1-3

(2) 4-40 x 3/16" Screws

Use 2 mounting holes on
opposite corners.

VersaTools Rack Shelf

Quarter Rack Wide
False Front Face Plate

Use 2 mounting holes on
opposite corners.

(2) 4-40 x 3/16"
Screws

1U Universal Rack Shelf

Both front false faceplates
use 2 screws.

1/4 Rack Wide Front False
Faceplate

1/2 Rack Wide Front False
Faceplate

About the IR 102 Kit

The Extron IR 102 Kit is an infrared (IR) remote control kit that
can control a variety of Extron switchers and other devices via
RS-232 or contact closure. This kit contains the following items:

• (1) IR 102 handheld remote control

• (1) IR 102 Rx Remote Receiver

• (1) IR Sensor

Mounting the IR 102 Rx Remote Receiver

The IR 102 Rx Remote Receiver can be mounted on a rack shelf,
under a desk or tabletop, or on a projector bracket. There are
many optional accessories for mounting the IR 102 Rx, including
the following items:

• 1U, 3.5" deep, VersaTools® rack shelf kit (part #60-190-20)

• 1U, 3.5" deep, basic VersaTools rack shelf (part #60-604-20)

• 1U, 6" deep, universal rack shelf kit (part #60-190-10)

• 1U, 6" deep, basic rack shelf (part #60-604-10)

• 1U, 9.5" deep, universal rack shelf kit (part #60-190-01)

• 1U, 9.5" deep, basic rack shelf (part #60-604-01)

• MBU 123 mini under-desk mounting bracket kit
(part #70-212-01)

• VersaTools projector mounting kits (PMK 100, #70-367-01;
PMK 300, #70-374-01; PMK 350, #70-563-02, -03)

Mounting the IR 102 Rx Remote Receiver on a
VersaTools rack shelf

N

Only products in the VersaTools line can be mounted

to a VersaTools shelf. Any 1U rack-mountable Extron
product can be mounted on the standard shelf.

Rack mounting

For optional rack mounting, mount the IR 102 Rx Remote
Receiver on one of the rack shelves listed above. On the
standard 9.5" deep rack shelf, the Remote Receiver mounts in
one of four locations to the rear of the rack or in one of four
locations to the front of the rack.

1. If rubber feet were previously installed on the bottom of

the Remote Receiver, remove them.

2. Mount the Remote Receiver on the rack shelf, using two 4-

40 x 3/16” screws in opposite (diagonal) corners to secure
the Remote Receiver to the shelf.

3. Install blank panel(s) or other unit(s) to the rack shelf.

4. Insert the shelf into the rack, aligning the holes in the shelf

with those of the rack.

5. Secure the shelf to the rack using the supplied machine

screws. This shelf can be mounted in the front or in the rear
of the rack.

Mounting the IR 102 Rx Remote Receiver on a
standard rack shelf

IR 102 Remote Control Kit • Installation and Operation

Installation and Operation, cont’d

1-4

IR 102 Remote Control Kit • Installation and Operation

1-5

I
R
1
0
2
R
x

U
N
I
V
E
R
S
A
L
I
R
R
E
M
O
T
E
R
E
C
E
I
V
E
R

R
S

­2
3
2
/

C
O
N
T
A
C
T

O
U
T

R
S

­2
3
2

T
x

1
2

3

4

5

+
5

+
1
2
V

6

C
O
N
T
R
O
L
O
U
T

I
R
I
N

C
O
N
T
A
C
T

M
O
D

D
E
M
O

D

P
O
W
E
R

1
2
V

.
5
A
M
A
X

R
S

­2
3
2

I
N

Ceiling

Projector

PMK 100
Projector
Mounting
Bracket

Mounting
Bolt

Projector Mounting

MBU 123
Under Desk Mounting Kit

Under Desk Mounting

PMK 300 Multi-Product
Projector Mounting Kit

IR 102 Rx or Other
VersaTools Device

U-Bolt

Rubber Pad

MBU 123
Under Desk Mounting Kit

Under Desk Mounting

Furniture mounting

Furniture mount the IR 102 Rx Remote Receiver using optional
mounting kit #70-212-01 as follows:

1. Attach the mounting brackets to the Remote Receiver with

the provided machine screws.

2. If rubber feet were previously installed on the bottom of

the Remote Receiver, remove them.

3. Hold the Remote Receiver with the attached brackets

against the underside of the table or other furniture.
Mark the location of the screw holes of the bracket on the
mounting surface.

4. Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)

deep in the mounting surface at the marked screw
locations.

5. Insert #8 wood screws into the four pilot holes. Tighten

each screw into the mounting surface until just less than
1/4" of the screw head protrudes.

6. Align the mounting screws

with the slots in the brackets
and place the Remote
Receiver against the surface,
with the screws through the
bracket slots.

7. Slide the receiver slightly

forward or back, then
tighten all four screws to
secure the Remote Receiver
in place.

Projector mounting the IR 102 Rx with kit #70-217-01

Alternatively the IR 102 Rx Remote Receiver can be projector
mounted using the optional VersaTools multi-product projector
mounting kit, part #70-374-01.

N

Only VersaTools products and most IP Link products

can be mounted using the multi-product projector
mounting kit.

To mount the IR 102 Rx using kit #70-374-01, do the following:

1. If necessary, remove feet from the bottom of the receiver.

2. Mount the IR 102 Rx to one of the bracket’s three mounting

plates. The device can be vertically mounted facing
either up or down, whichever is most convenient. See the
following illustration.

Use two supplied 4-40 x 3/16 screws in opposite (diagonal)

corners to secure the device to the bracket.

Projector mounting

Projector mounting procedures differ depending on the
mounting kit you use.

Projector mount the IR 102 Rx using optional mounting kit
#70-217-01 as follows:

1. Attach the mounting brackets to the Remote Receiver with

the provided machine screws.

2. If rubber feet were previously installed on the bottom of

the receiver, remove them.

3. Secure the Remote Receiver to a projector mount or

other surface by inserting the mounting bolt through the
bracket’s slotted hole and tightening the bolt.

Projector mounting the IR 102 Rx with kit #70-374-01

IR 102 Remote Control Kit • Installation and Operation

Installation and Operation, cont’d

1-6

IR 102 Remote Control Kit • Installation and Operation

1-7

Extron
PMK 350

Low Profile Two-product
Projector Mounting Kit

Extron
Power Supply

Plastic Tie

Extron
IR 102 Rx

Cover Sheet

Front Plate

Rear Plate

Rubber Pad

U-bolt

N

On the side mounting plates, devices are typically

mounted on the outside of the bracket. On the front
mounting plate, devices are typically mounted on the
inside of the bracket.

N

The front mounting plate is 1/4" taller than the side

plates. This size helps ensure the accessibility of buttons
or connectors.

3. Affix the black rubber pad to the mounting plate.

4. Place the U-bolt around the ceiling pole and insert the two

legs of the U-bolt through the slotted holes on the bracket’s
mounting plate and then through the slotted holes on the
backing brace.

For a typical (1.5" to 2.0" diameter) pole — The supplied

U-bolt fits a typical ceiling pole.

For a smaller or larger pole — Locally obtain a U-bolt that

fits the ceiling pole. The slotted holes on the bracket will
accommodate a U-bolt for pole sizes from 1.0" to 2.5" in
diameter.

5. Secure the bracket to the U-bolt with the included hex

nuts, washers, and lock washers.

The IR 102 Rx can also be mounted using other kits, as shown
below.

Connecting the IR 102 Rx to a Switcher

1. Power down the switcher.

2. Connect the IR 102 Rx to the switcher via the RS-232 or

contact closure ports, available on both 9-pin and captive
screw connectors.

3. Position the IR sensor at the best location for the IR 102
handheld remote control.

4. Connect the IR Sensor to the IR In connector on the Remote
Receiver.

5. Connect the external power supply to the Remote Receiver,
then plug one end of a standard IEC power cord into
the power supply and the other end into a 100-240 VAC,
50/60 Hz power source.

6. Power up the switcher.

Projector mounting the IR 102 Rx with the PMK 350
kit, part #70-563-02 or #70-563-03

IR 102 Remote Control Kit • Installation and Operation

Installation and Operation, cont’d

1-8

IR 102 Remote Control Kit • Installation and Operation

1-9

IR 102 Rx UNIVERSAL IR REMOTE RECEIVER

RS-232/

CONTACT

OUT

RS-232

Tx Rx1 2 3 4 5+5

+12V

6

CONTROL OUT

IR IN

CONTACT

MOD

DEMOD

POWER
12V
.5A MAX

RS-232

IN

4

1

2

3

6

5

Power Supply

Output Cord

Captive Screw

Connector

Power Wiring.eps

A A

SECTION A–A

Modulated IR

+12VDC

21' max.

Ground ( )

Ground ( )

IR In connector wiring_030606.eps

IR In

MOD

DEMOD

+12V

+5V

or

IR In

MOD

DEMOD

+12V

+5V

IR

Sensor

IR Link

1 Tx Rx2 3 4 5 6

RS-232

CONTROL OUT

CONTACT

Pin - 1

Pin - 2

Pin - 3

Pin - 4

Pin - 5

Pin - 6

Gnd

Tx

Rx

Gnd

Contact Closure

RS-232

Features and Connections

IR 102 Rx Remote Receiver front and rear panels

Power LED — When lit, this LED indicates power is applied.

a

The LED blinks during communication activity.

Power connector — Plug the external 12 V power supply

b

into this 2-pole captive screw connector. The power supply is
included with the unit. The figure below shows how to wire the
connector.

C

When connecting the power supply, voltage polarity

is extremely important. Applying power with
incorrect voltage polarity could damage the power
supply and the Remote Receiver. Identify the power
cord negative lead by the ridges on the side of the
cord.

IR In connector — Plug the cable from the IR sensor or from an

c

Extron IR Link infrared repeater into this 3.5 mm, 5-pole captive
screw connector.

N

The maximum cable length for the IR sensor is 21 feet

(6.4 meters). Cut or extend the IR sensor’s cable as
needed.

Power connector wiring

N

W

To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.

Do not tin the stripped power supply leads before

installing the captive screw connector. Tinned wires are
not as secure in the captive screw connectors and could
pull out.

The two power cord wires must be kept separate

while the power supply is plugged in. Remove
power before continuing.

Contact / RS-232 (Control Out) connector (captive screw) —

d

Plug the contact closure/RS-232 output
cable into this 3.5 mm, 10-pole captive screw
connector, and plug the other end of the cable
into the switcher’s contact closure/RS-232
control port. This permits the IR 102 Rx
Remote Receiver to control the switcher.

N

The IR 102 Kit can be used with

an Extron MPS 112 switcher only
when the switcher is in single switch
mode. Refer to the MPS 112 User’s

Manual.

RS-232/Contact – Out connector (9-pin D) — Plug the RS-232

e

or contact closure output cable into this 9-pin D connector,
and plug the other end of the cable into the switcher’s contact

IR 102 Remote Control Kit • Installation and Operation

Installation and Operation, cont’d

1-10

IR 102 Remote Control Kit • Installation and Operation

1-11

Female (In)

5 1

9 6

Male (Out)

1 5

6 9

Pin RS-232 In Contact Closure

1 — Input #1
2 TX

—

—
3 RX
4 — Input #2
5 Gnd Gnd
6 —
7 —
8 —
9 —

Input #3
Input #4
Input #5
Input #6

Gnd

RS-232 Out

—

TX

RX

—

—
—
—
—

Universal Remote

INPUT/OUTPUT SELECTION

1 2 3 4

5 6 7 8

9 0 +10 ENTER

IR 102

IR 102 Rx UNIVERSAL IR REMOTE RECEIVER

RS-232/

CONTACT

OUT

RS-232

Tx Rx1 2 3 4 5+5

+12V

6

CONTROL OUT

IR IN

CONTACT

MOD

DEMOD

POWER
12V
.5A MAX

RS-232

IN

SW6 VGA Ars

REMOTE

100-240V 0.2A

INPUTS

1

2

3

4

5

50-60Hz

OUTPUT

OUTPUT

L R

SW6 VGA Ars

6

Universal Remote

INPUT/OUTPUT SELECTION

1 2 3 4

5 6 7 8

9 0 +10 ENTER

IR 102

REMOTE

IR 102 Rx Remote
Control Receiver

IR 102 Remote Control

IR Sensor

Up to 21' Cable

6' Cable

Power Supply

Control System/PC

SW6 VGA Ars Switcher

closure/RS-232 control port. This permits the IR 102 Rx Remote
Receiver to control the switcher. The pin assignments are listed
in the following table.

N
N

See the note for d.

Connect RS-232 or contact closure, but not both.

Remove the pins that are not needed.

N

The cable used to connect the RS-232/Contact – Out

connector to a computer, control system, or contact
closure device may need to be modified by removing
pins or cutting wires. If unneeded pins are connected,
the system may "hang" (suspend communication
indefinitely).

For RS-232 control and IR control

, use a control cable with only
pins 2, 3, and 5 connected. If other pins are connected,
either cut the wires to the other pins if the cable has a hard­shelled connector, or remove the other pins if the cable has
a molded plug.

Installing Batteries in the Remote

The IR 102 Handheld Remote Control is shown at
right. Install two AAA batteries in the remote as
shown below. The battery compartment is in the
front, bottom side of the remote control.

Operation

To select an input using the IR 102 remote control, aim the
handheld unit at the IR detector and press the numeric button
for the desired input. For switchers with ten or more inputs,
press the +10 key to add ten to the input number selected. For
example, to select input 17, press the +10 key, then the 7 key.
The maximum operating range is 30 feet.

Working together with a control system

f

For contact closure

, use a control cable with pins 2 and 3 not
connected. If the cable has pins 2 and 3 connected, cut the
wires to these pins if the cable has a hard-shelled connector,
or remove these pins if the cable has a molded plug.

RS-232 In connector — Plug the RS-232 input cable into this

9-pin D connector to permit a PC or control system to control
the switcher, even though the switcher’s RS-232 connector
is occupied by the IR 102 Rx Remote Receiver. The pin
assignments are shown in the table above.

A typical IR 102 Kit application

The IR 102 Remote Receiver connects via cable to the switcher’s
rear panel RS-232 connector, and it uses the switcher’s RS-232
interface for input selection. The Remote Receiver also has an
RS-232 input connector, to permit the switcher to be controlled
by a PC or control system, even when the switcher’s RS-232 port
is occupied by the IR 102 Remote Receiver.

N

The remote control can operate a switcher only if the

switcher is configured as master, with no switchers
slaved to it. Refer to the switcher’s manual for
information on switcher configuration.

Installation and Operation, cont’d

IR 102 Remote Control Kit

Appendix A

A

1-12

Specifications, Part Numbers,

and Accessories

Specifications

Included Parts

Accessories

IR 102 Remote Control Kit • Installation and Operation

IR 102 Remote Control Kit • Specifications, Part #s, Accessories

Specifications, Part Numbers, and Accessories

IR 102 Remote Control Kit • Specifications, Part #s, Accessories

A-2

A-3

Specifications

General

Carrier frequency .......................... 38 kHz

Max. IR range (between IR handheld remote control and IR sensor)

30 feet (9.1 meters)

Max. IR sensor cable length ......... 21 feet (6.4 meters)

External power supply (included)

Power input requirements ........... 12 VDC, approximately 30 mA

Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /

Rack mount .................................... Yes, with an optional 1U rack shelf, part

Enclosure type ............................... Metal

Enclosure dimensions ................... 1.7” H x 4.4” W x 3.3” D

Product weight .............................. 0.4 lbs (0.2 kg)

Shipping weight ........................... 2 lbs (1 kg)

Vibration ........................................ ISTA 1A in carton

Listings............................................ UL, CUL

Compliances ................................... CE, FCC Class A, VCCI, AS/NZS, ICES

MTBF ............................................... 30,000 hours

Warranty ........................................ 3 years parts and labor

N

Specifications are subject to change without notice.

100 VAC to 240 VAC, 50/60 Hz, external,

autoswitchable; to 12 VDC, 1 A, regulated

10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) /

10% to 90%, noncondensing

#60-190-01 or 60-604-01; or a VersaTools

rack shelf, part #60-190-20 or 60-604-20;

also under-furniture-mountable with

optional brackets #70-212-01

or projector-mountable with optional

brackets #70-217-01/70-077-04

(1U high, quarter rack wide)

4.2 cm H x 11.1 cm W x 8.4 cm D

(International Safe Transit Association)

Included Parts

These items are included in each order for an IR 102 Remote Kit
(part #70-224-01):

Included parts Replacement

IR 102 Rx Remote Receiver
IR 102 Handheld Remote Control
12 VDC, 1 A external power supply kit 70-055-01
IR sensor on a 21-foot cable
RS-232 Series male-to-female cable

(6'/1.8 m)
IEC power cord

Tweeker (small screwdriver)
Hook-and-loop fasteners

3.5 mm, 2-pole captive screw connector 10-319-15

3.5 mm, 5-pole captive screw connector 10-319-10

3.5 mm, 10-pole captive screw connector 10-319-11
User’s manual

Accessories

Accessories Part number

1U, 3.5" deep, VersaTools® rack shelf kit
(RSF 123)

1U, 3.5" deep, basic VersaTools rack shelf
(RSB 123)

1U, 6" deep, universal rack shelf kit
(RSU 126)

1U, 6" deep, basic rack shelf (RSB 126)
1U, 9.5" deep, universal rack shelf kit

(RSU 129)
1U, 9.5" deep, basic rack shelf (RSB 129)

VersaTools mini under-desk mounting
bracket kit (MBU 123)

VersaTools mini projector mounting kit
(PMK 100)

part number

70-224-10

26-433-03

60-190-20

60-604-20

60-190-10

60-604-10
60-190-01

60-604-01
70-212-01

70-367-01

Specifications, Part Numbers, and Accessories

Accessories Part number

VersaTools multi-product projector
mounting kit (PMK 300)

VersaTools multi-product projector
mounting kit (PMK 350)

70-374-01

70-563-02, -03

A-4

IR 102 Remote Control Kit • Specifications, Part #s, Accessories