Installation Guide
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
www.extron.com
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
© 2002 Extron Electronics. All rights reserved.
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
RGB 460
xi xi
xi
xi xi
/470
xixi
xi
SC Series
xixi
Installation Guide
Steel City Floorbox-Mounted Interface
68-636-04 Rev. A
Printed in the USA
06 02
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product's enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation
et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de
pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et
consignes marqués sur le matériel ou présentés dans la documentation
utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni
d’outils non recommandés par le fabricant du matériel car cela
risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau
durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre
instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad
para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario, deben ser
obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main
power system with a grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all
power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to
be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-
serviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced.
Replace it only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation
principale comportant un fil de terre (neutre). Le troisième contact (de mise à la
terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du
module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-
maintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne
doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,
ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces
ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la
batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype
equivalent recommande par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit
einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der
dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.
Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,
sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen
Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht
im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder
unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes
sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die
Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse
aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen
Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten
blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.
Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen
Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor
neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la
acometida de alimentación eléctrica al equipo, desenchufar todos los cables de
alimentación en el panel trasero del equipo, o desenchufar el módulo de
alimentación (si fuera independiente), o desenchufar el cable del receptáculo de
la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se
deben instalar en lugares donde no sean pisados ni apretados por objetos que se
puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para
evitar riesgo de electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar
expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and
workmanship for a period of three years from the date of purchase. In the event of
malfunction during the warranty period attributable directly to faulty workmanship
and/or materials, Extron Electronics will, at its option, repair or replace said products
or components, to whatever extent it shall deem necessary to restore said product to
proper operating condition, provided that it is returned within the warranty period,
with proof of purchase and description of malfunction to:
USA, Canada, South America, Europe, Africa, and the Middle East:
and Central America:
Extron Electronics Beeldschermweg 6C
1230 South Lewis Street 3821 AH Amersfoort
Anaheim, CA 92805, USA The Netherlands
Asia: Japan:
Extron Electronics, Asia Daisan DMJ Bldg. 6F,
135 Joo Seng Road, #04-01 3-9-1 Kudan Minami
PM Industrial Bldg. Chiyoda-ku, Tokyo 102-0074
Singapore 368363 Japan
This Limited Warranty does not apply if the fault has been caused by misuse,
improper handling care, electrical or mechanical abuse, abnormal operating conditions
or non-Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number).
This will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with
respect to the product and its quality, performance, merchantability, or fitness for any
particular use. In no event will Extron Electronics be liable for direct, indirect, or
consequential damages resulting from any defect in this product even if Extron
Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Extron Electronics, Europe
Extron Electronics, Japan
Table of Contents
About this Guide ....................................................................... 1
Installation Overview ............................................................. 2
Installation Instructions........................................................ 3
Preparing the site and cables................................................... 3
Mounting the faceplate to the floorbox ................................ 4
Specifications ............................................................................. 7
Included Parts ............................................................................. 8
Accessories ................................................................................... 8
Cables.............................................................................................. 9
Male-to-male VGA cables ........................................................... 9
Male-to-male 90° VGA cables .................................................. 9
Adapter kits .............................................................................. 9
High resolution cables .............................................................. 9
All trademarks mentioned in this manual are the properties of their respective owners.
68-636-04 Rev. A
xixi
xixi
xi/470
xi SC Series • Table of Contents
xixi
xixi
Printed in the USA
06 02
iRGB 460
Table of Contents, cont’d
About this Guide
This guide contains instructions for mounting eight different
Extron computer interfaces and an adapter plate in Steel City®
floor boxes. The interfaces are standard RGB 400xi series
interfaces tailored to fit in the different Steel City floor boxes.
The Steel City floorbox-mountable interface models are:
• RGB 460
300 MHz (-3dB) bandwidth interfaces configured for
installation in an AFM 2 floor box.
• RGB 460
300 MHz (-3dB) bandwidth interfaces configured for
installation in an AFM 4 floor box.
• RGB 464
300 MHz (-3dB) bandwidth interfaces with S-video,
composite video, unbalanced stereo audio, and RJ-45
pass-through connectors configured for installation in an
AFM 6 floor box.
• RGB 468
300 MHz (-3dB) bandwidth interfaces with an opening for
three single space (single height) Architectural Adapter
Plates (AAPs) configured for installation in an AFM 6
floor box.
The SC-AFM8 adapter plate is a blank faceplate for the AFM 8
floorbox, to which any standard Extron shallow-profile 2-gang,
3-gang, or 4-gang wall mountable device can be mounted.
Specifically, the SC-AFM8 will accommodate:
• One 4-gang faceplate product (examples: RGB 468xi,
RGB 460xi Dual, or TP T 468)
• Two 2-gang faceplate products (for example: one
RGB 420xi and one TP T 460)
• One 2-gang faceplate product (for example: one
RGB 460xi) and two 1-gang blank plates
• One 3-gang faceplate product (for example: one
RGB 464xi) and one 1-gang blank plate
In this guide, the terms “RGB 400xi SC series interface” or “RGB
470xi series interface” and “Interface” are used interchangeably.
The term “faceplate” can be any of the interface faceplates or the
SC-AFM8 adapter plate.
For information about operating and wiring the interface, refer
to the RGB 400
470xi Series User’s Manual, Part #68-661-01, depending on the
specific product you are using.
xixi
xi SC-AFM2 and RGB 472
xixi
xixi
xi SC-AFM4 and RGB 472
xixi
xixi
xi SC-AFM6 and RGB 474
xixi
xixi
xi SC-AFM6 and RGB 478
xixi
xi
Series User Manual, Part #68-542-01, or the RGB
xixi
xi
SC-AFM2 —
xixi
xixi
xi
SC-AFM4 —
xixi
xixi
xi
SC-AFM6 —
xixi
xixi
xi
SC-AFM6 —
xixi
ii RGB 460
xixi
xixi
xi/470
xi SC Series • Table of Contents
xixi
xixi
RGB 460
xixi
xixi
xi/470
xi SC Series • Installation Guide
xixi
xixi
1
Installation, cont’d
CAUTION
Installation Cable
Steel City Box
Screw
Braided Shield
CAUTION
Installation Overview
CAUTION
Install the interface as follows:
Turn all of the equipment off. Make sure that the
1
computer, the interface, and the output devices (projector/
monitor, speakers) are all turned off and disconnected
from the power source.
Select the installation location and install the electrical
2
floorbox. Refer to the documentation that was included
with the floorbox.
Route the cables that connect to the rear of the interface (or
3
the device(s) to be installed in the SC-AFM8 adapter plate).
Set the gain and DIP switches (or the switch(es) on the
4
rear of the device(s) to be installed in the SC-AFM8
adapter plate). Refer to the RGB 400xi Series User Manual,
Part #68-542-01, the RGB 470xi Series User Manual, Part
#68-661-01, (or the appropriate manual(s) for the device(s)
to be installed in the SC-AFM8 adapter plate).
For the SC-AFM8 adapter plate only, secure the device(s)
5
to be installed to the front of the faceplate.
Installation and service must be performed by
authorized personnel only. These products must be
used with UL approved electrical boxes.
Installation Instructions
The interface must be installed into an
Underwriters Laboratories (UL) approved Steel
City electrical floor box. The floorbox is not
included with the interface; the installer is
responsible for obtaining and installing the box.
Preparing the site and cables
Choose a location that allows cable runs without interference.
Allow enough depth for both the floorbox and the cables. You
need to run the conduit (if required by local code) and cables
under the floor before installing the interface.
The installation must conform to national and local electrical
codes and to the interface’s size requirements. Dimensional
drawings and actual-size cut-out templates are provided at the
end of this guide.
1. Install the floorbox in accordance with the documentation
that accompanied the box.
2. Feed cables through the floorbox punch-out holes, and
secure them with cable clamps to provide strain relief.
3. Exposed cable shields (braids or foil) are potential sources
of short circuits. Trim back and/or insulate shields with
heat shrink (figure 1).
2
Connect the video, audio, and power cables to the rear of
6
the device. Refer to the RGB 400xi Series User Manual,
Part #68-542-01, the RGB 470xi Series User Manual, Part
#68-661-01, (or the appropriate manual(s) for the device(s)
to be installed in the SC-AFM8 adapter plate).
Connect power cords and turn on the projector or monitor
7
and audio device, the interface, and the computer.
The picture should now appear, and sound should be
8
audible. If not, ensure that all devices are plugged in and
receiving power. Check the cabling and switch settings,
and make adjustments as needed.
Disconnect power from all the devices.
9
Mount the faceplate into the electrical box. See Mounting
10
the faceplate to the floorbox in this manual.
Restore power to the devices.
11
For the SC-AFM8 adapter plate only, as necessary, secure
12
blank 1-gang faceplate(s) to the front of the faceplate.
xixi
xixi
xi/470
xi SC Series • Installation Guide
xixi
xixi
Figure 1 — Grounding outer braided and foil
shields, AFM 2 box
To prevent short circuits, the outer foil shield can be
cut back to the point where the cable exits the cable
clamp. Both braided and foil shields should be
connected to an equipment ground at the other end
of the cable.
xixi
RGB 460
xi/470
xixi
xixi
xi SC Series • Installation GuideRGB 460
xixi
3
Installation, cont’d
8-32 x 1/4" Machine Screw
Locking T abs
in Slots
4. For the SC-AFM8 adapter plate only, secure the device(s)
to be installed to the front of the faceplate with machine
screws (figure 2).
H. SHIFT
MONITOR
MIN/MAX
INPUT
RGB 460xi
WITH ADSP
TM
NO MONITOR
MONITOR
AUDIO
Figure 2 — Securing the device to the face plate,
SC-AFM8 only
5. Set the gain and DIP switches (or the switch(es) on the
device(s) to be installed in the SC-AFM8 adapter plate) and
cable and test the interface or other device before securing
the device into the wall box. The switches and cables will
be inaccessible after installation. Refer to the RGB 400xi
Series User Manual, Part #68-542-01 (or the appropriate
manual(s) for the device(s) to be installed in the SC-AFM8
adapter plate).
Mounting the faceplate to the floorbox
1. Disconnect the power supply to remove power from the
interface (or the device connected to the SC-AFM8 adapter
plate).
2. If installed, remove the floor box’s top panel and trim
frame.
3. Place the faceplate through the opening in the floor and
into the floorbox. Take care not to damage the cables,
which lay behind the interface in the bottom of the box.
4. Mount the faceplate to the knockout box.
a. For the RGB 460
RGB 472
xixi
xi SC-AFM2, hook the two locking tabs on
xixi
xixi
xi SC-AFM2 and
xixi
the bottom of the faceplate into the slots on the
bottom of the box is mounted. Secure the faceplate to
the top of the floorbox with the included 8-32 x 1/4”
machine screw (figure 3).
Figure 3 — RGB 460
b. For the RGB 460
RGB 464
RGB 468
xixi
xi
SC-AFM2 installed
xixi
xixi
xi SC-AFM4, RGB 472
xixi
xixi
xi SC-AFM6, RGB 474
xixi
xixi
xi SC-AFM6, and RGB 478
xixi
xixi
xi SC-AFM6,
xixi
xixi
xi SC-AFM4,
xixi
xixi
xi SC-AFM6,
xixi
secure the faceplate to either side of the floorbox with
the included 10-32 x 3/8” machine screws (top) and
8-32 x 3/8” machine screws (bottom) (figure 4).
c. For the SC-AFM8 adapter plate, secure the faceplate
to the top and bottom of the floorbox with the
included 8-32 x 3/8” machine screws (figure 5).
xixi
xixi
xixi
xi/470
4
xi SC Series • Installation Guide
xixi
xixi
RGB 460
xi/470
xixi
xixi
xi SC Series • Installation GuideRGB 460
xixi
5
Installation, cont’d
10-32 x 3/8"
Machine Screw
8-32 x 3/8"
Machine
Screw
Figure 4 — RGB 460
Figure 5 — SC-AFM8 adapter plate installed
5. Install the floor box’s top panel and trim frame.
6. Reconnect the power supply.
xixi
xi
SC-AFM4 installed
xixi
8-32 x 3/8"
Machine Screws
10-32 x 3/8"
Machine Screw
8-32 x 3/8"
Machine
Screw
Specifications
This guide shows power requirements and physical
specifications only. For electrical and functional specifications,
refer to the RGB 400xi Series User Manual, Part #68-542-01 or the
RGB 470xi Series User’s Manual, Part #68-661-01, depending on
the specific product you are using.
General
Power ............................................. 12VDC, 0.42 A, 5 watts, external (the
power supply is included.)
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /
10% to 90%, non condensing
Operating +32° to +122°F (0° to +50°C) /
10% to 90%, non condensing
Rack mount ................................... No, but Steel City floorbox mountable
Enclosure type .............................. Metal
Enclosure dimensions
RGB 460xi/472xi SC-AFM2
Plate .......................... 2.9" H x 3.5" W (7.2 cm H x 8.9 cm W)
Back enclosure ........ 2.7" H x 3.3" W x 1.1" D
(6.9 cm H x 8.4 cm W x 2.8 cm D)
(Depth excludes front panel connectors
and controls.)
RGB 460xi/472xi SC-AFM4
Plate .......................... 2.9" H x 5.8" W (7.2 cm H x 14.8 cm W)
Back enclosure ........ 2.7" H x 3.3" W x 1.1" D
(6.9 cm H x 8.4 cm W x 2.8 cm D)
(Depth excludes front panel connectors
and controls.)
RGB 464xi/474xi SC-AFM6
Plate .......................... 2.9" H x 8.9" W (7.2 cm H x 22.6 cm W)
Back enclosure ........ 2.7" H x 3.3" W x 1.1" D
(6.9 cm H x 8.4 cm W x 2.8 cm D)
(Depth excludes front panel connectors
and controls.)
RGB 468xi/478xi SC-AFM6
Plate .......................... 2.9" H x 8.9" W (7.2 cm H x 22.6 cm W)
Back enclosure ........ 2.7" H x 3.3" W x 1.1" D
(6.9 cm H x 8.4 cm W x 2.8 cm D)
(Depth excludes front panel connectors
and controls.)
SC-AFM8 adapter plate .. 4.4" H x 9.4" W (11.2 cm H x 23.7 cm W)
xixi
xixi
xi/470
xi SC Series • Installation Guide
xixi
xixi
Specifications are subject to change without notice.
xixi
RGB 460
xi/470
xixi
xixi
xi SC Series • Installation GuideRGB 460
xixi
76
Installation, cont’d
Included Parts
These items are included in each order for the indicated
interface:
Included parts Part number
RGB 460xi SC-AFM2 gray 60-463-01
RGB 460xi SC-AFM4 gray 60-464-01
-or-
RGB 464xi SC-AFM6 gray 60-465-01
-or-
-or-
RGB 468xi SC-AFM6 gray 60-466-01
-or-
RGB 472xi SC-AFM2 gray 60-516-01
-or-
RGB 472xi SC-AFM4 gray 60-517-01
RGB 474xi SC-AFM6 gray 60-520-01
-or-
-or-
RGB 478xi SC-AFM6 gray 60-522-01
SC-AFM8 mounting kit* 70-203-01
12VDC, 1.0A external power supply kit 70-055-01
RGB 400xi Series User’s Manual 68-542-01
-or-
RGB 470xi Series User’s Manual 68-661-01
RGB 460xi SC Series Installation Guide 68-636-01
* SC-AFM8 does not include the power supply, RGB 400xi
Series User’s Manual, or RGB 470xi Series User ’s Manual.
Accessories
Accessories Part number
3.5 mm stereo plug 10-306-01
Mac/VGA adapter
(VGA male, Mac female, Mac RGBS, 1’) 26-340-01
Mac HV/VGA adapter
(VGA male, Mac female, Mac RGBHV, 1’) 26-340-02
Mac 35/VGA 6’ adapter
(15-pin male Mac II, 15-pin HD male VGA) 26-287-01
SY VGA/XGA adapter
(15-pin male to 5 BNC male, 6’) 26-173-01
SY 15 HDM RGBHVF
(15-pin male VGA to 5 BNC female, 2’) 26-397-01
Cables
Male-to-male VGA cables Part number
VGA M6’ MHR 26-238-01
VGA M3’ MHRA (with audio) 26-490-01
VGA M6’ MHRA (with audio) 26-490-02
VGA M12’ MHRA (with audio) 26-490-03
Male-to-male 90° VGA cables Part number
VGAM 90 MHRA 6’ (with audio) 26-510-02
Adapter kits Part number
Mac 15-pin HD F adapter cable kit w/audio 70-156-01
13W3 15-pin HD F adapter cable kit w/audio 70-157-01
High-resolution cables Part number
BNC-5-3’HR 26-260-15
BNC-5-6’HR 26-260-01
BNC-5-12’HR 26-260-02
BNC-5-25’HR 26-260-03
BNC-5-50’HR 26-260-04
BNC-5-75’HR 26-260-16
BNC-5-100’HR 26-260-05
BNC-5-3’HRP (plenum) 26-378-01
BNC-5-6’HRP (plenum) 26-378-02
BNC-5-12’HRP (plenum) 26-378-03
BNC-5-25’HRP (plenum) 26-378-04
BNC-5-50’HRP (plenum) 26-378-05
BNC-5-75’HRP (plenum) 26-378-06
BNC-5-100’HRP (plenum) 26-378-07
Bulk installation cable
(14-conductor, non-plenum), 500’ HR 22-120-02
Bulk installation cable
(17-conductor, plenum), 500’ HR 22-111-03
xixi
xixi
xixi
xi/470
8
xi SC Series • Installation Guide
xixi
xixi
RGB 460
xi/470
xixi
xixi
xi SC Series • Installation GuideRGB 460
xixi
9
Installation, cont’d
10
RGB 460
xixi
xixi
xi/470
xi SC Series • Installation Guide
xixi
xixi
Loading...