Extreme Networks x-605 Instruction Manual
TABLE OF CONTENTS
Introduction.........................................................................................................................01
Special features..................................................................................................................02
Specifications................................................................. ....................................................04
.................................................05
Warning and safety notes.....................................................................................................06
................................................................................................11
....................................................................................13
Charging of lithium battery....................................................................................................17
Balance charging of lithium battery........................................................................................18
.............................................................................................19
...........................................................................................20
...........................................21
.............................................................................................22
............................................................................................23
........................................24
....................................................................................................25
................................................................................................26
..........................................................................................................27
...............................................................................................................28
........................................................................................29
..................................................................................................30
...........................................................................................................32
Lithium polymer balance charge program connection diagram
Program flow chart...............
Fast charging of lithium battery
Storage control of lithium battery
Discharging of lithium battery.....................................................
Charging of NiCd/NiMH battery
Discharge of NiCd/NiMH battery
Charge/discharge and discharge/charge cycle of NiCd/NiMH battery
Charging of the Pb battery
Discharging of the Pb battery
Storage data program
Load data program
Various information in the program
Warning and error message
Warranty and service
Initial parameter setup (users set up)
01
INTRODUCTION
Introduction
Thank you for purchasing the X-605 LiPro Balance Charger .This product is a rapid charger with
a high performance microprocessor and specialized operating software. Please read this entire
operating manual completely and attentively before using this product, as it covers a wide range
of information on operating and safety. Or please do use this product in company with a
specialist!
LCD screen
.Scroll through th e Main Menu
.Stop any charge pr ocesses
Alter values
cells in balance charge mode
See the status of in dividual
.Resume or start ch arge processes
.Confirm an action
Temp.Sensor
Input power cable
11-18V DC
Balance led sockets
JST-XH ports
Output charge lead
4mm banana plug
SPECIAL FEATURES
Special features
Optimized operating software
X-605 features the so-called AUTO function that set the feeding current during the process of
charging or discharging. Especially for Lithium batteries, it can prevent the overcharging which
may lead to an explosion due to the user's fault. It can disconnect the circuit automatically and
alarm once detecting any malfunction. All the programs of this product were controlled through
two way linkage and communication, to achieve the maximum safety and minimize the trouble.
All the settings can be configured by users!
Internal independent lithium battery balancer
X-605 employs an individual-cell-voltage balancer. It isn't necessary to connect an
external balancer for balance charging.
Balancing individual cells battery discharging
During the process of discharging, X-605 can monitor and balance each cell of the battery
individually. Error message will be indicated and the process will be ended automatically if the
voltage of any single one cell is abnormal.
Adaptable to various type of lithium battery
X-605 is adaptable to various types of Lithium batteries, such as Li-ion, LiPo and the new LiFe
series of batteries.
Fast and storage mode of lithium battery
Purposes to charge Lithium battery varies, fast charge reduce the duration of
charging, whereas store state can control the final voltage of your battery, so
as to store for a long time and protect useful time of the battery.
02
Maximum safety
Delta-peak sensitivity: The automatic charge termination program based on the
principle of the Delta-peak voltage detection. When the battery's voltage
exceeds the threshold, the process will be terminated automatically.
SPECIAL FEATURES
Automatic charging current limit
You can set up the upper limit of the charging current when charging your NiCd or
NiMH battery; it is useful for the NiMH battery of low impedance and capacity in
the 'AUTO' charging mode.
Capacity limit
The charging capacity is always calculated as the charging current multiplied by
time. If the charging capacity exceeds the limit, the process will be terminated
automatically when you set the maximum value.
Temperature threshold*
The battery's internal chemical reaction will cause the temperature of the
battery to rise. If the temperature limit is reached, the process will be terminated.
* This function is available by connecting optional temperature probe, which is
not included in the package.
Processing time limit:
You can also limit the maximum process time to avoid any possible defect.
Data store/load
The maximum ten batteries data can be stored for users convenience. You can keep the
data pertaining to program setting of the battery of continuous charging or discharging.
Users can call out these data at any time without any special program setting.
03
Cyclic charging/discharging
1 to 5 cyclic and continuous process of charge> discharge or discharge> charge is
operable for battery refreshing and balancing to stimulate the battery’s activity.
04
Operating voltage range:
Circuit power:
Charge current range:
Discharge current range:
Current drain for balancing Li-po:
NiCd/NiMH battery cell count:
li-ion/Polymer cell count:
Pb battery voltage:
Weight:
Dimensions:
DC11.0~18.0 Volt
AC to DC adaptor (DC11.0~18.0V/5A)
Max. charge power 50W
Max. discharge power5W
0.1~5.0A
0.1~1.0A
300mAh/cell
1~15cell
1~6 series
2V~20V
265g(Net Weight)
133.2×80.6×33mm
Specifications
SPECIAL FEATURES
Fai lur e to connect as show n in thi s di agram will dam age thi s char ger.
WARNING:
The mai n bat ter y leads must be connect ed al ong with the bal ance lead connect or as shown bef ore char ging
your bat ter y ..
If usi ng crocodi le cl ips as shown in above diagr am , make sur e they ar e unabl e to touch
toget her !
WARNING:
LITHIUM POLYMER BALANCE CHARGE PROGRAM
CONNECTION DIAGRAM
Lithium polymer balance charge program
connection diagram
This diagram shows the correct way to connect your battery to the X-605 while charging in the
balance charge program mode only.
!
05
WARNING AND SAFETY NOTES
WARNING AND SAFETY NOTES
These warnings and safety notes are particularly important.Please follow the instructions
for maximum safety; otherwise the charger and the battery can be damagedor at worst it
can cause a fire.
Never leave the charger unattended when it is connected to its power supply. If any
malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operation
manual.
Keep the charger well away from dust, damp, rain, heat, direct sunshine and
vibration. Never drop it.
The allowable input voltage is 11~18V DC
This charger and the battery should be put on a heat-resistant, noninflammable and
nonconductive surface. Never place them on a car seat, carpet or similar. Keep all the
inflammable volatile materials away from operating area.
Make sure you know the specifications of the battery to be charged or discharged to
ensure it meets the requirements of this charger. If the program is set up incorrectly,
the battery and charger may be damaged .It can cause fire or explosion due to
overcharging. This warranty is not valid for any damage or subsequent damage
arising as a result of a misuse or failure to observe the procedures outlined in this
manual.
06
WARNING AND SAFETY NOTES
07
Voltage level: 2.0V/cell
(Lead-acid) Max. charge voltage: 2.46V/cell
Allowable fast charge current: 0.4C or less
Discharge voltage cut off level: 1.75V/cell or higher
Voltage level: 3.3V/cell
Max. charge voltage: 3.6V/cell
Allowable fast charge current: 4C or less
Discharge voltage cut off level: 2.0V/cell or higher
Voltage level: 3.7V/cell
Max. charge voltage: 4.2V/cell
Allowable fast charge current: 1C or less
Discharge voltage cut off level: 3.0V/cell or higher
Voltage level: 3.6V/cell
Max. charge voltage: 4.1V/cell
Allowable fast charge current: 1C or less
Min. discharge voltage cut off level: 2.5V/cell or higher
Voltage level: 1.2V/cell
Allowable fast charge current: 1C-2C (depends on the performance of cell)
Discharge voltage cut off level: 0.85V/cell (NiCd), 1.0V/cell(NiMH)
NiCd/NiMH
Li-ion
LiPo
LiFe
Pb
WARNING AND SAFETY NOTES
To avoid short circuit between the charge lead always connect the charge cable to the
charger first, then connect the battery. Reverse the sequence when disconnecting.
!
!
!
Do not connect more than one battery pack to this charger at any one time.
Never attempt to charge or discharge the following types of batteries.
A battery pack which consists of different types of cells (including
different manufacturers)
A battery that is already fully charged or just slightly discharged.
Non-rechargeable batteries (Explosion hazard).
Batteries that require a different charge technique from NiCd, NiMh, LiPo
or Gel cell (Pb, Lead acid).
A faulty or damaged battery.
A battery fitted with an integral charge circuit or a protection circuit.
Batteries installed in a device or which are electrically linked to other
components.
Batteries that are not expressly stated by the manufacturer to be suitable
for the currents the charger delivers during the charge process.
08
WARNING AND SAFETY NOTES
!
!
Please bear in mind the following points before commencing charging:
Did you select the appropriate program suitable for the type of battery you are
charging?
Did you set up adequate current for charging or discharging?
Have you checked the battery voltage? Lithium battery packs can be wired in
parallel and in series, i.e. a 2 cell pack can be 3.7V (in parallel) or 7.4V (in
series).
Have you checked that all connections are firm and secure? Make sure there
are no intermittent contacts at any point in the circuit.
Charging
During charge process, a specific quantity of electrical ener gy is fed into the battery. The
charge quantity is cal culated by multiplying charge current b y charge time. The maximum
permissible charge current varies depending on the battery ty pe or its performance, and c an
be found in the information by the battery manufacturer. Only batteries that are expressly
stated to be capable of qu ick-charge are allowed to be charged at rat es higher than the
standard charge current.
Connect the battery to t he terminal of the charger : red is positive and black is negative. Due to
the differ ence between resistanc e of cable and connector, the charger can not detect
resistance of the batt ery pack, the essential re quirement for the charger to work properly is
that the charge lead sho uld be of adequate conductor cross-section, and high quality
connectors which are normally gold-plated should be fitted to b oth ends.
09
Loading...