eSTREAM™ 4K Control User Guide
1.
Remote control layout
TV input source select
TV power/standby
Guide
Play/Pause, Rewind, Fast-
Forward, Skip Ahead, and Return
Netflix
Home
6
Navigation and OK
7
Back
8
9
Volume up and down
10
Number Keys
11
Clear
12
Accessibility
13
Infra-red (IR) window
14
Microphone
15
STB power/standby
16
Google Assistant
17
APPS
18
YouTube
19
VOD menu
20
Exit
21
22
23
24
25
®
Voice control
TiVo
Channel/Page up and down
Mute
Last
Information
2. Inserting batteries
Slide the battery
housing cover
downwards to
remove
Insert two
2
AAA batteries
observing the
correct polarity
Battery information
Do not mix different types of battery, or old and new batteries.
Refit the battery
housing cover
Do not use rechargeable batteries.
Remove the batteries from the remote control if you are not
going to use it for several weeks, to avoid the risk of leakage.
Please follow your environment and local regulations and
dispose of old batteries in a responsible manner.
Do not attempt to recharge the batteries.
Immediately remove any leaking batteries.
Take care when handling leaking batteries as they may cause
burns to the skin or eyes, or other physical injuries.
3. Operation
When you press a key, point the remote control towards the
front of the STB to ensure correct operation. Do not cover the
infra-red (IR) window at the front of the remote control and at
the front of the STB.
When a key is pressed either the STB key will flash or, if a TV
brand has been entered, the TV key will flash, depending on
which product is being controlled by the remote control.
If you press a key for more than 30 seconds the remote control
will stop transmitting commands to preserve battery life.
9. Learning mode
5. Controlling the TV: Auto Search (search all brands)
6. Controlling the STB: manual pairing
7. Controlling the STB: auto pairing
8. Factory reset
manual pairing (continued)
4. Controlling the TV: Brand Search
3. Make sure your TV is turned on. The STB does not need to be turned on for the
brand search.
4. Press 1 and 3 for at least three seconds until the STB key flashes twice and remains
on.
5. Enter the brand code for your TV. On each digit entry the STB key will flash.
6. If successful the STB key will flash once and remain on. If unsuccessful the TV key
will give a long flash and the remote control will revert to normal operation. No
brand code will be stored.
7. To check you can control your TV, press and hold either TV or MUTE. When the
TV turns off or mutes, release TV or MUTE.
8. Press Back to leave the brand search mode.
If you change your TV to a different brand the remote control will require
re-programming. Repeat this brand search procedure with the brand code for your
new TV.
The Maxi ATV remote control can learn a key function from another ‘source’
remote control.
1. Choose your ‘target key’ on the Maxi ATV remote control. It must be one of the
following keys: TV, TV input, VOL+, VOL-, MUTE. The target key you have chosen
will learn a function from the source remote control.
2. Press 4 and 6 for three seconds until the STB key flashes twice then remains on.
3. Press your target key within 30 seconds:
• if valid, the STB key will give a confirmation flash and remain on.
• if invalid, or you do not press within 30 seconds, the STB key will give a long flash
and return to user mode.
4. Hold the Maxi ATV remote control 3 - 6 cm from the source remote control with
the IR windows facing each other, then press your target key on the source remote
control (e.g. if your target key on the Maxi ATV remote control is mute, press mute
on the source remote control).
5. If the IR signal is received correctly, the STB key will turn off and the Maxi ATV
remote control will return to normal mode (note: this can overwrite a previously
learned code).
6. If the IR signal is not received correctly, or is received after 30 seconds, the Maxi
ATV remote control will not store the code from the source remote control: it will
give a long flash and return to user mode.
7. If the Back key is pressed on the Maxi ATV remote control while it is waiting
for an IR signal, the STB key will give a long flash and return to user mode. (If the
target key is pressed, any learned code on it is cleared.)
8. To clear the target key, press 4 and 6 for at least three seconds until the STB key
flashes twice then remains on. Press your <target key> twice. The STB key will flash
to confirm the target key is cleared.
If you cannot find the TV brand code by the brand search method then auto search
can be used. Note: this process may take several minutes to find your TV brand
code.
Make sure your TV is turned on. The STB does not need to be turned on for the auto
search.
Your remote control has to be ‘paired’ to the STB to control it. Pairing can be manual
or automatic. A remote control can only pair with one STB at a time.
For manual pairing the STB must be in pairing mode, which is:
• for two minut
es after the STB boots up
or
• when the pairing page of the setup wizard is shown (this depends on the STB
firmware version and may not be shown)
or
• when pairing instructions are shown by the middleware (this depends on the
middleware application and may not be shown)
1. Press 1 and 6 for at least three seconds until the STB key flashes twice then stays
on.
2. Enter the key sequence 9 8 1. The TV key will flash twice and the remote control
returns to factory settings: Bluetooth mode, Samsung brand code (1150) and
unpaired.
Auto pairing can be triggered by the remote control in two cases:
• after the batteries have been inserted.
• after any key is pressed, and the STB key flashes to confirm the keypress.
To auto pair the remote control and the STB:
Ensure the STB is powered on and the STB key on the remote control is not lit.
Then follow steps 1 and 2 in the manual pairing section above.
To pair manually:
1. Press HOME and OK for at least three seconds until the TV key flashes to
acknowledge. The timeout for pairing is 60 seconds.
2. If pairing is successful:
The TV key flashes once to confirm pairing and the remote control changes to
Bluetooth mode (the STB may indicate this change, depending on the middleware or
firmware version).
If pairing is unsuccessful:
The TV key gives a long flash to indicate an error (the STB may indicate this change,
depending on the middleware or firmware version).
During pairing no remote control keys will work except the STB key. You must press
The TV, TV input, VOL+, VOL- and MUTE keys on the remote control can be
programmed to operate your TV. To do this, your remote control must first learn
the ‘brand code’ of your TV. By default, the remote control is programmed with the
most common brand code 1150 (Samsung).
1. Press HOME and 1 for at least three seconds to switch the remote control to
infra-red (IR) mode. The TV key flashes twice when the remote control has
switched to IR mode.
If you make a mistake, press Back to exit the procedure. The remote control will
rever
t to normal operation. No TV brand code will be stored.
2. Find the 4-digit brand code for your TV from the list in section 10: TV IR codes.
1. Press HOME and 1 for at least three seconds to switch the remote control to
infra-red (IR) mode. The TV key flashes twice when the remote control has
switched to IR mode.
2. Press 1 and 3 together for at least three seconds until the STB key flashes twice
and remains on.
3. Enter the 4-digit code 9 9 9 9. On each keypress the STB key will flash.
4. If successful the STB key will flash once and remain on. If unsuccessful the TV key
will give a long flash and the remote control will revert to normal operation.
5. To check the TV control is operating, press and hold either the TV or MUTE key.
When the TV turns off or mutes, release the TV or MUTE key.
6. Press Back
then the remote control is unable to control your TV.
to leave the auto search mode. If brand search and auto search fail,
Back to stop pairing or to use another function.