evo 10-0095-LP INSTALLATION INSTRUCTIONS AND OPERATION MANUAL

OWNER & INSTALLATION MANUAL
R
Cooktop
Affinity 25G
Evo A󰀩nity 25G
Residential Gas Cooktop
For Outdoor Use Only
Tested & Listed By
Certication: ANSI Z21.58-2015/CSA 1.6-2015/CSA 2.17-2017 OMNI Report # 0141GM007S Part #: Residential Models: 10-0095-NG, 10-0095-LP Doc: 9-9-2019 Copyright © 2019
Portland Oregon USA
evoamerica.com
Pour obtenir un manuel en français, veuillez appeler Evo, Inc. au 503-626-1802.
For a French Language Manual, please call Evo, Inc. at 503-626-1802.
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
INSTALLATION INSTRUCTIONS
HIGH
VOLTAGE
Affinity 25G
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND,
AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL.
DANGER
WARNING
CAUTION
CAUTION
POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH
POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY
POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY.
Helpful tips and technique instructions are shown.
Model #_______________________________ Serial # _________________________________
Date Purchased ________________________ Location Purchased _______________________
Date Installed __________________________ Location Installed _________________________
2
Notes
To Installer or Person Uncrating Grill:
Leave these instructions with purchaser.
To Purchaser:
Keep these instructions for future reference.
Complete Now For Future Reference
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Warnings
INSTALLATION INSTRUCTIONS
Affinity 25G
FOR YOUR SAFETY
1. Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.
2. An LP Tank not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING
It is the responsibility of the assembler/owner to assemble, install and maintain gas grill. Do not let children operate or play near your grill. Failure to follow these instructions could result in serious personal injury and / or property damage.
FOR YOUR SAFETY
If You Smell Gas:
1. Shut o󰀨 gas to appliance.
2. Extinguish any open ame.
3. Remove grill cooking surface.
4. If odor continues, immediately call your gas supplier or your re department.
5. Evacuate all personnel from the area.
WARNING
This symbol identies the most important safety messaging in this manual. When you see this symbol, be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and carefully follow all of the messages.
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
WARNING
Grill should only be used outdoors, in a well ventilated space, and should not be used in a building, garage, or any other enclosed area. Never operate near ammable liquids or vapors. Do not install or use grill within 36” of combustible ceiling materials, and 12” from back and sides of grill. Grill shall not be located under unprotected overhead made of combustible construction within 36” from top of grill. Do not obstruct the ow of combustion and ventilation air, including ventilation of cylinder enclosures, if applicable.
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
3
INSTALLATION INSTRUCTIONS
Affinity 25G
READ FIRST
IMPORTANT PRODUCT AND SAFETY INFORMATION
WARNING INSTALLATION OF THIS UNIT MUST BE DONE BY A QUALIFIED PLUMBER.
INCORRECT INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/ OR DAMAGE TO EQUIPMENT. THIS UNIT MUST CONFORM WITH ALL LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE
NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, OR THE NATURAL GAS AND PROPANE INSTALLATION CODE, CSA B149.1, AS APPLICABLE
INCLUDING:
1. THIS UNIT AND ITS INDIVIDUAL SHUTOFF VALUE MUST BE DISCONNECTED FROM THE GAS SUPPLY PIPING SYSTEM DURING ANY PRESSURE TESTING OF THE SYSTEM AT TEST PRESSURES IN EXCESS OF 1/2 PSI (3.45 kPa).
2. THIS UNIT MUST BE ISOLATED FROM THE GAS SUPPLY PIPING SYSTEM BY CLOSING ITS INDIVIDUAL MANUAL SHUTOFF VALVE DURING ANY PRESSURE TESTING OF THE GAS SUPPLY PIPING SYSTEM AT TEST PRESSURES EQUAL TO OF LESS THAN 1/2 PSI (3.5 kPa).
WARNING DO NOT DIRECTLY INSTALL THIS UNIT TO COMBUSTIBLE SURFACES,
AND DO NOT USE COMBUSTIBLE MATERIALS IN THE CONSTRUCTION OF ANY COUNTER, STAND, OR OTHER DEVICE WHICH WILL COME INTO DIRECT CONTACT WITH THE BURNER CHASSIS (SEE PAGE
WARNING IMMEDIATELY AFTER CONNECTING GAS SUPPLY LINE AND BEFORE
FIRST IGNITION, CHECK ALL GAS CONNECTIONS WITH SOAPY WATER TO TEST FOR LEAKS.
WARNING KEEP WATER AND ALL COOKING SPILL OVERS AWAY FROM FRONT
CONTROL PANEL AND ALL OPEN SERVICE AREAS. NEVER HOSE UNIT, OR SPRAY UNIT WITH PRESSURIZED CLEANING SOLUTIONS.
CAUTION CAREFULLY FOLLOW ALL INSTALLATION INSTRUCTIONS AND
CONSTRUCT ALL COUNTER SPACE, STANDS, OR OTHER SURFACES TO THE RECOMMENDED INSTALLATION SPECIFICATIONS AS OUTLINED IN
THIS MANUAL.
CAUTION THIS UNIT IS HEAVY AND SHOULD BE INSTALLED BY TWO PEOPLE.
USE NECESSARY BLOCKING FOR LOCATING AND INSTALLING COOK SURFACE.
CAUTION ALWAYS KEEP ANY AND ALL FLAMMABLE LIQUIDS AND COMBUSTIBLE
MATERIALS AWAY FROM UNIT. DO NOT STORE TOWELS OR UTENSILS, OR ANY OTHER ITEMS ON UNIT’S DRIP PAN.
CAUTION DO NOT CLEAN THE COOK SURFACE WITH GRILL BRICKS OR CLEANING
SOLUTIONS. USE ONLY GRILL SCREENS AND GRILL PADS AND FOLLOW THE PRESCRIBED METHOD OF CLEANING AS OUTLINED IN THIS MANUAL.
NOTICE THE SERIAL NUMBER AND MODEL INFORMATION LABEL PLATE IS
LOCATED INSIDE THE RIGHT-SIDE SPILLOVER DOOR.
NOTICE INSTALLATION OF ANY VENT HOODS OR FIRE EXTINGUISHER SYSTEMS
MUST CONFORM TO THE NATIONAL, STATE, AND LOCAL BUILDING AND ALL APPLICABLE UNIFORM CONSTRUCTION CODES.
NOTICE DURING THE FIRST FEW HOURS OF OPERATION IT IS NORMAL FOR OILS
USED IN THE MANUFACTURING PROCESS TO BURN OFF AND GIVE AN ODOR OR SLIGHT PETROLEUM SMOKE.
4
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
INSTALLATION INSTRUCTIONS
Affinity 25G
EVO RESIDENTIAL LIMITED WARRANTY TERMS
Evo, Incorporated warrants to the original residential consumer-purchaser that the Evo grill shall be free from rust-through on all metal surfaces and shall be free from defects in materials and workmanship under normal and reasonable use from the original date of purchase. Evo promises to replace, at its determination, any product or component that is defective and covered under this warranty for as long as you, the registered original consumer-purchaser, owns the grill. This is your sole and exclusive remedy. This warranty is for the benet of the original consumer-purchaser and is non-transferable. This warranty is subject to the limitations, exclusions and other provisions listed below.
Limitations Involving Materials and Components:
Warranty does not apply to normal wear and tear, which are expected over the course of ownership. The materials and components listed below are covered according to the following schedule from the original date of purchase:
• One Year – electrical and electronic components [including, but not limited to, electronic displays, overlay and membrane switches, temperature sensors (K-Value Thermal Couple), hot surface igniters, computers, transformers, heater elements, relays, igniters, ignition controllers, wiring, switches, encoders, outlets and plugs]
• One Year – gas components [including, but not limited to, gas regulator, gas hoses, manifold assemblies]
• One Year – accessories and repair parts
The Warranty Registration Card (or online warranty registration form available at www.evoamerica.com/content/ residential-warranty-registration) must be completed and returned/submitted to Evo, Incorporated within 30 days from the date of purchase. The original purchase invoice or payment record must be retained and produced upon request if claims are made under this warranty. To receive a replacement Warranty Registration Card, write or call the address listed at the bottom of this page. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily determined.
THIS WARRANTY APPLIES ONLY TO PRODUCTS PURCHASED AND LOCATED WITHIN THE UNITED STATES OR CANADA.
WHAT IS NOT COVERED BY THIS WARRANTY
1. Conditions and damages resulting from any of the following:
a. Improper or inadequate installation, delivery, use, storage or maintenance b. Any repair not authorized in writing by Evo, Inc., any modications, misapplications, or unreasonable use c. Improper setting of any control d. Harsh environmental conditions, including, but not limited to, continual seawater spray, high pressure water, and direct contact with corrosive chemicals and materials e. Excessive or inadequate electrical, or gas supply f. Accidents, natural disasters, acts of God g. Conditions covered by the purchaser’s insurance h. Cleaning supplies and lters
2. Products purchased or utilized for commercial use without the express authorization of Evo, Incorporated for such use
3. Labor not pre-authorized by Evo, Incorporated, and labor not performed by an authorized Evo service agency or representative
4. Pre-authorized warranty labor performed outside of normal business hours, and at overtime and premium rates
5. The cost of service or a service call to:
a. Identify or correct installation errors b. Transport the product or component for service to/from the manufacturer or service center c. Instruct the user of the proper use of the product
6. The cost for any inconvenience, personal injury or property damage due to failure of the product, and cost of damage arising out
of the transportation of the product which is covered under di󰀨erent terms with the carrier
7. Natural variations in color and nishes that are inherent to the material and unavoidable (and therefore not defects)
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, SUITABILITY, QUALITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIODS SPECIFIED ABOVE FOR THE PARTS DESCRIBED THEREIN. EVO, INCORPORATED MAKES NO OTHER WARRANTY AND WILL NOT BE LIABLE FOR ANY DIRECT OR INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Neither Evo manufacturer representatives and dealers, nor the retail establishment selling this product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above. The maximum liability to Evo, Incorporated in any event, shall not exceed the purchase price of the product paid by the original consumer-purchaser. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
5
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
INSTALLATION INSTRUCTIONS
Affinity 25G
INSTALLATION AND USE CHECKLIST
PAGE
SAFETY WARNINGS 2 - 4
RESIDENTIAL WARRANTY 5
UNPACKING COOKTOP COMPONENTS 7
CLEARANCE TO COMBUSTIBLES DIMENSIONS 8
PREPARE COUNTERTOP FOR INSTALLATION 9 - 12
INSERT CHASSIS IN COUNTER TOP 13
INSTALL DRIP PAN AND DRIP PAN GASKET 14 - 15
ASSEMBLING COOK SURFACE RETAINING FASTENERS 16
INSTALL COOK SURFACE AND TIGHTEN FASTENERS 17 - 19
CONNECTING GAS & CHECKING FOR LEAKS 20 - 24
LOCATING THE GAS BURNER AND GAS ORIFICE JETS 25
CHECK LIST FOR INSTALLATION PROCEDURES 26
TEMPERATURE CONTROL AND LIGHTING INSTRUCTIONS 27 - 28
RECOGNIZING ABNORMAL GAS OPERATION 29
REPLACING ELECTRONIC IGNITOR BATTERY 30
MAINTAINING SPILLOVER TRAYS 31
AFFINITY 25G DIMENSIONS 32
COOKING SURFACE MAINTENANCE 33
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
6
Drip Pan
Unlatch pan from circular skirt, then carefully lift and separate drip pan from unit and place next to installation area. Take care
not to scratch drip pan during installation.
Remove Tie Down Bolts and Tabs
holding chassis to packing crate base using 7/16” wrench.
INSTALLATION INSTRUCTIONS
Affinity 25G
UNPACKING COOKTOP COMPONENTS
Cooking Surface:
Lift and separate cooking surface from unit and place next to installation area.
The cooking surface is heavy. Use caution when lifting.
Drip Pan Gasket:
Gasket is secured
to top of drip tray.
Remove gasket
for reinstallation.
from crating box
installation area.
Metal Right Angle Brackets: Unscrew from unit and keep screws and brackets handy for rst installation step.
from drip tray
and set aside
Chassis:
Lift chassis
and place on
its side next to
Use caution
since ignition
components
are exposed.
STEP 1: As you are unpacking the crate, make sure you locate all components before installation.
7
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
12” CLEARANCE
FROM COOKING
SURFACE TO
COMBUSTIBLE
BACK WALL MATERIALS.
IF INSTALLING
ALONGSIDE
ANOTHER 25G
UNIT, PROVIDE
2” MINIMUM
CLEARANCE
FROM EDGE
OF DRIP PANS.
INSTALLATION INSTRUCTIONS
Affinity 25G
CLEARANCE DIMENSIONS
36” CLEARANCE FROM COOKING
SURFACE TO COMBUSTIBLE
CEILING MATERIALS.
12” CLEARANCE FROM COOKING SURFACE TO COMBUSTIBLE SIDEWALL MATERIALS.
Minimum 3” clearance required under unit venting to 22 sq/in of combustible air. The minimum environmental temperature for safe use of the Evo A󰀩nity 25G
should not be below 32°F ( 0° C).
CLEARANCE TO COMBUSTIBLE CONSTRUCTION FROM CHASSIS
Combustibles Non-combustibles
Back * 3/8” 0”
Sides * 3/8” 0”
Bottom 3” 3”
CLEARANCE TO COMBUSTIBLE CONSTRUCTION FROM COOKING SURFACE
Top 36”
Sides 12”
Back 12”
* 3/8” of cement board lined enclosure to chassis.
Read the instructions carefully in this booklet to install the
Evo A󰀩nity 25G Cooktop to a metal, stone or wood countertop surface.
Cabinet layout and construction may vary.
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
8
INSTALLATION INSTRUCTIONS
COUNTERTOP INSTALLATION (1 of 4)
Affinity 25G
Cabinetry Box: 1-1/2” below countertop surface
NOTE:
If the dimensions for the countertop overhang and countertop depth cutout are not followed, there will be a conict with the door swing which may hinder access to the spillover waste containers.
TOP VIEW
"
11
16
31
804.86mm
304.88mm
"
15
64
1
31.40mm
12"
304.80mm
23
"
32
1
"
3
4
11
298.45mm
43.66mm
"
1
2
22
571.50mm
drip pan cutout.
front to center of
From countertop
24"
609.60mm
OPENING IN COUNTERTOP FRONT
12"
13
"
32
1
Countertop with substrate underlayment
COUNTERTOP OVERHANG TO CABINET FRONT
35.68mm
STEP 2: Mark the nished position of the Evo A󰀩nity 25G drip pan on the countertop using the dimensions shown. The circular dimension of 31” 11/16” is the diameter of the drip pan to the outside ange material thickness (located to the inside of the half-rolled bead edge). The drip pan cutout must be made precisely to these dimensions (or at a maximum +1/16”) so that the half-rolled top bead on the drip pan edge overhangs the cutout dimension by .25”. (See following page for more details).
9
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
INSTALLATION INSTRUCTIONS
COUNTERTOP INSTALLATION (2 of 4)
Affinity 25G
Black o-ring under drip pan bead
CORRECT ALIGNMENT OF DRIP PAN
AND CHASSIS TO COUNTERTOP
INCORRECT ALIGNMENT OF DRIP PAN
AND CHASSIS TO COUNTERTOP
Possible reasons for incorrect alignment:
1. Top of cabinetry box is less than 3 cm from countertop
2. Chassis mounting brackets are too high.
STEP 2 continued: Make sure cabinetry box is 1-1/2” below countertop surface and mounting brackets are positioned correctly so drip pan and chassis are aligned to countertop. (see diagrams above). A black o-ring is recessed in the top bead and designed to create a seal against the countertop.
Also ensure allowance for the countertop overhang as shown on the SIDE VIEW (see next
page).
When you have conrmed the position is correct, cut the countertop and substrate.
Evo, Inc., 20560 SW 115th Ave., Tualatin, OR 97062 USA
Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | support@evoamerica.com
10
Loading...
+ 23 hidden pages