EverFocus EDH5210B, EDH5210W User Manual
1
Operation Instruction
EDH5210B(W)-00
EDH5201WEDH5201B
HDcctv 1080p
Indoor 3-Axis Dome Camera
EDH5210B
EDH5210W
EVERFOCUS ELECTRONICS CORPORATION
Operation Instruction
© 2013 EverFocus Electronics Corp
Please read this manual rst f
retained for future reference. The information in this manual was current when published.
The manufacturer reserves the right to revise and improve its products. All speci cations are
therefore subject to change without notice.
or correct installation and operation. This manual should be
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in
any form or by any means without written permission of the EverFocus Electronics Corporation.
3
PRECAUTIONS
1. Do not install the camera near electric or magnetic elds.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic elds generated from these devices may distort the video image or otherwise
interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor
introduce materials other than those recommended herein.
introduction of corrosive materials may result in equipment failure or other damage.
Improper disassembly or
3. Try to avoid facing the camera toward the sun.
cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination
beyond the capability of the camera to compensate.
In some circumstances, direct sunlight may
4. Keep the power cord away from water and other liquids and never touch the power
cord with wet hands.
hands may result in electric shock.
Touching a wet power cord with your hands or touching the power cord with wet
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, re.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use
lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp
soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive
agents for cleaning of any part of the camera.
7.
Do not operate the camera beyond the speci ed temperature, humidity or power source ratings.
This camera is suitable for indoor operation. Use the camera at temperatures within -10°C~50°C (14°F~122°F) and
in an indoor environment; this device is not rated as weather proof. The input power source is 12VDC. The use of
properly fused or Class 2 power limited type supplies are highly recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind,
snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors
which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to
provide additional support for the camera.
4
ATTENTION! This is a class A product which may cause radio interference in
a domestic environment; in this case, the user may be urged to take adequate
measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one of the following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di erent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modi cations not expressly approved by the
party responsible for compliance could void the users’ authority to operate this
equipment.
5
Table of Contents
1. PRODUCT OVERVIEW .................................................................
1.1 FEATURES .............................................................................................. 7
1.2 ACCESSORY PARTS LIST ..................................................................... 8
1.3 SPECIFICATIONS ................................................................................... 9
1.4 DIMENSIONS .......................................................................................... 10
7
2. CAMERA COMPONENT DESCRIPTION ...................................... 11
3. INSTALLATION ............................................................................. 12
4. OSD Structure.............................................................................. 14
6
Loading...