Page 1
ED910 & ED930
720p Analog High Definition
True Day/Night Indoor Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: Nov., 2014
Page 2
Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity between 20%~ 80%; this device is not rated as
submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / -
polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera
to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.
2
Page 3
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
3
Page 4
Contents
1. Introduction...................................................................................................................... 5
1.1 Packing List ..................................................................................................................... 5
1.2 Features .......................................................................................................................... 6
2. Cable Description .............................................................................................................. 6
3. Installation ....................................................................................................................... 7
3.1 Installation and Adjustment ........................................................................................... 7
4. Configuration in the OSD Menu ........................................................................................ 13
5. Specifications ................................................................................................................... 17
4
Page 5
ED910/930 eZ.HD Indoor Dome Camera
Model
Image Sensor
Resolution
IR LEDs
Day / Night
ED910
1/2.8" SONY 1.37M pixels
CMOS
720p
No
True Day/Night
ED930
Yes (18 LEDs)
Dome Camera x 1
Screw x 3
User Manual x 1
Screw Driver x 1
Test Lead x 1
Plastic Anchor x 3
DC Power Pigtail Cable x 1
Quick Installation Guide x 1
Template Plate x 1
1. Introduction
Get incredible performance in bright light environments or low light, and the resolution listed in the
specification from the actual camera you install. To take full advantage of the amazing resolution
available from this advanced imaging technology, the Everfocus eZ.HD Series ED910/930 uses a
vari-focal lens together with 1/2.8" SONY 1.37M pixels CMOS to deliver 720p high resolution.
Combined with a useable native low light sensitivity of 0.08 lux without using digital slow shutter.
The camera truly provides HD images without compromising its 720p video quality, Digital Wide
Dynamic Range for clear color images in the most challenging of bright or unbalanced scene lighting
conditions. Moreover, the ED930 features 18 LEDs with range of 30m / 100 feet; it also provides
true day/night enhanced images in low light environments with guaranteed ZERO ghosting. The
cameras are equipped with 3-axis rotation design, allowing wall or ceiling mounting. Your choice of
vari-focal 2.8~12mm DC iris lens for easily adjustable field of view; dual voltage operation and a full
suite of OSD Menu and DSP functions controllable at the camera (3DNR to save DVR HDD space,
privacy masking, mirroring, and much more) This is the camera that you have been waiting for to
create analog CCTV systems that produce astounding image clarity in a wide range of indoor
applications at the widest range of light levels. The ED910/930 supports both NTSC and PAL
scanning systems, which can be switched via OSD.
1.1 Packing List
5
Page 6
ED910/930 eZ.HD Indoor Dome Camera
No.
Name
Descriptions
1
Power Cable
Connect to a 12VDC or 24VAC power source.
2
Dual Video Output
720p and 960H output, using a 75 Ohm BNC-type coaxial
cable.
3
Test Lead
Connect to a monitor for setting image aim and focus.
4
DC Power Pigtail Cable
Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).
1.2 Features
720p with high flexibility and performance for astounding image
1/2.8" SONY 1.37M pixels CMOS, delivers amazing high sensitivity
Vari-focal 2.8~12mm DC iris lens to capture the desired field of view
18 IR LEDs for 30m/100ft. range -depending on scene IR reflectivity (for ED930)
D-WDR to improve the visibility under high contrast scene
Provides 3D Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments
Support 720p & 960H analog signal output, which can be easily switched by OSD
Easy lock installation by screwing the base plate to the surface and then locking the
camera to the base plate without mounting screws
2. Cable Description
6
Page 7
ED910/930 eZ.HD Indoor Dome Camera
3. Installation
3.1 Installation and Adjustment
ED910 without LED ED930 with LED
Camera Breakdown
7
Page 8
ED910/930 eZ.HD Indoor Dome Camera
Base PlateCamera Body
The Base Plate is unlocked to the Camera Body.
Important Notice
Please be noted the camera Base Plate may loosen when you take out the camera from the pack. It
is because the Base Plate is attached to the Camera Body without locking tightly in order to simplify
the installation procedure.
1. Stick the Template Plate on the position where you want to attach the camera, drill the
three holes on the Template Plate for screwing the camera with the supplied Screws and
Anchors, and the circle in the middle only if you want to wire the cables through the wall
/ ceiling (the “Line out” mark represents the factory wiring position).
2. Insert the supplied three Anchors into the holes.
8
Page 9
ED910/930 eZ.HD Indoor Dome Camera
3. Rotate counter-clockwise to remove the camera cap, press and pull to remove the liner.
Remark: Hold the liner with one hand, press and pull to remove the liner (refer to the “arrow”
label which marked to the liner)
4. Push the inner click outward and rotate the base plate counter-clockwise, then remove
the camera body from the base plate. (See the yellow arrow label on the camera)
9
Page 10
ED910/930 eZ.HD Indoor Dome Camera
5. Screw the base plate to the wall / ceiling using the supplied three screws. Note that if you
want to wire the cables through the wall / ceiling, break the middle part of the base plate.
6. Lock the camera body back to the base plate, align the arrow marks and rotate the camera
body clockwise. A “click” sound should be heard when the camera body and the base
plate are firmly locked. (See the direction arrow labels on the camera)
10
Page 11
ED910/930 eZ.HD Indoor Dome Camera
7. Connect the camera to the 12 VDC or 24 VAC power source and an AHD DVR or a monitor.
8. Optionally connect the camera to a monitor using the supplied Test Lead for adjusting
camera angles, focus, zoom and configuring OSD menu
a. Connect one end of the Test Lead to the camera and the other end to a monitor.
b. To adjust camera angles, simply tilt, pan or rotate the camera.
11
Page 12
ED910/930 eZ.HD Indoor Dome Camera
c. To configure the OSD Menu, using the function button.
Note: The function button is not only for direction control, also for switching Video
format and Video output. Please follow the detailed instruction as below:
Press the "DOWN" button key over 5s to switch video format from PAL to NTSC.
Press the "LEFT" button key over 5s to switch video output from 720p to 960H
(720p is the default).
Press the "RIGHT" button key over 5s to switch video output from 960H to 720p.
d. To adjust the Zoom / Focus, using the Zoom / Focus screws. Tighten the zoom /Focus
screws using the supplied Screw Driver.
9. Put the liner back and secure the camera cover cap back to the camera.
12
Page 13
ED910/930 eZ.HD Indoor Dome Camera
No.
Main
Sub Menu
Sub Menu / Function
1
Lens
DC*
Mode
Indoor*
Outdoor
Min Shu.
NTSC: 1/30*
PAL: 1/25*
Max. Shu.
NTSC: 1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
PAL: 1/50,FLK,1/200,
1/400,1/1000,
1/2000,1/5000*,
1/10000, 1/50000
0 – 15(0*)
Manual
2
Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
AGC
0 – 15(15*)
Sens-up
Off*
Auto
Sens-up
X2, X4*, X6, X8, X10, X15, X20, X25, X30
Brightness
1-100(40*)
D-WDR
Off*
On
Level
0-8(8*)
Auto
Defog
Off*
Auto
Pos/Size
Position, Size,↑,↓,→,←
Gradation
0-2(0*)
Default
3
Backlight
Off*
BLC
Level
Middle*, High, Low
Area
Position, Size,↑,↓,→,←
4. Configuration in the OSD Menu
You can use the function buttons on the rear panel of the camera body to configure camera settings
in the OSD menu:
13
Page 14
ED910/930 eZ.HD Indoor Dome Camera
Default
HSBLC
Select
Area1*, Area2, Area3, Area4
Display
Off
On*
Position, Size,↑,↓,→,←
Black
Mask
On*/Off
Level
0-100(20*)
Model
All Day*
Night
AGC Level
0-255(48*)
Default
4
White
Balance
ATW*
AWC→SET
Indoor
Outdoor
Manual
Blue
1-500(50*)
Red
0-100(50*)
AWB
5
Day &
Night
Ext
(Ext* for ED930)
D→N(Delay)
0-60(1*)
N→D(Delay)
0-60(1*)
Auto
(Auto* for ED910)
D→N(AGC)
1-255(240*)
D→N(Delay)
0-60(1*)
N→D(AGC)
1-255(50*)
N→D(Delay)
0-60(5*)
Color
B/W
Burst
Off*/On
IR Smart
Off( Off* for ED910)
On
(On* for
ED930)
Level
0-15(4*)
Area
Position, Size,↑,↓,
→,←
IR PWM
Off
0-100(100*)
6
NR
2DNR
Middle*/Low/Off/High
3DNR
Middle*/Low/Off/High
7
Special
Cam Title
Off*
On
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→←
↑↓()ˉ-_▊/=&:~,.
D-effect
Freeze
Off*/On
Mirror
Off*, Mirror, V-flip, Rotate
14
Page 15
ED910/930 eZ.HD Indoor Dome Camera
Neg.
Image
Off*/On
Motion
Off*
On
Select
Area1*,Area2,Area3,Area4
Display
On*
Position, Size,↑,↓,→,←
Off
Sensitivity
0-100(64*)
Color
Green*, Blue, White, Red
Trans
1.00*,0.75,0.50,
0.25
Alarm
View Type
Off, Block, Outline, All*
OSD View
On*/Off
Alarm Out
On*/Off
Alarm Sig
High*, Low
Time
1-15(3*)
Default
Privacy
Off
On
Select
Area1*,Area2,Area3,Area4
Display
Off
Color*
Position, Size,↑,↓,→,←
Mosaic
Position, Size,↑,↓,→,←
Inv
Position, Size,↑,↓,→,←
Color
White*, Black, Red, Blue, CYAN, Yellow,
Green
Trans
1.00*,0.75,0.50,
0.25
Default
Language
ENG*/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On*
AGC level
0-255(65*)
Level
0-100(100*)
White DPC
Off
On*
Pos/Size
Position, Size,↑,↓,→,←
Start
Close the iris then press
DPC View
Off*/On
Level
0-60(5*)
AGC
0-14(14*)
15
Page 16
ED910/930 eZ.HD Indoor Dome Camera
Sens-up
x2*, x4, x6, x8,x10, x15,
x20, x25, x30
Black DPC
Off*
On
Pos/Siz
Position, Size,↑,↓,→,←
Start
Press Enter
DPC View
Off*/On
Level
0-255(255*)
RS485
CAM ID
0-255(1*)
ID Display
Off*/On
Baud Rate
2400,4800,9600,19200 ,38400
8
Adjust
Sharpness
Off
Auto*
Level
0-10(6*)
Start AGC
0-255(50*)
End AGC
0-255(200*)
CRT/LCD
CRT
Black Level
0-60(0*)
Blue Gain
0-100(50*)
Red Gain
0-255(50*)
LCD*
Gamma
User*,0.45,0.50,0.55,0.60,
0.65,0.70,0.75,0.80,0.85,0.
90,
0.95,1.00
Blue Gain
0-100(50*)
Red Gain
0-100(50*)
LSC
Off*/On
Video. Out
PAL/NTSC
9
Exit
Save& END /Reset/Not Saved
16
Page 17
ED910/930 eZ.HD Indoor Dome Camera
P/N
ED910
ED930
Pickup Device
1/2.8" SONY 1.37M pixels CMOS
Video Format
NTSC and PAL( can be switched via OSD)
Effective Pixels
1280 (H)*720 (V)
Scanning System
Progressive Scan
Sensitivity
0.08 Lux
0 Lux with IR on
S/N Ratio
Over 50 dB (AGC OFF)
Electronic Shutter
AUTO, Manual (X30~1/ 50000), FLK
Video Output
BNC 1.0Vp-p 75Ω
Gamma Correction
0.45
Lens Type
2.8-12mm DC Iris
BLC
OFF/BLC/HS BLC Selectable
AGC
0~15 Levels
White Balance
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Sync Mode
Internal
Day/Night
Ext, Auto, Color, B/W, True D/N with ICR，Auto
IR LED
N/A
18 Units
IR Distance
N/A
Up to 30m/100ft. range(depending
on scene IR reflectivity)
OSD Languages
12-Language
Digital Noise Reduction
2DNR/3DNR, Off
Defog
Off/Auto(under B/W mode)
D-WDR
On/Off
Sens-up
Off/On(x30~x2)
Mirror
Horizontal/Vertical/HV
Motion Detection
Off/On for 4 selectable zones (On screen indication on alarm)
Privacy Mask
Off/On for 4 selectable zones
Environmental
Indoor
Power Source
12VDC/24VAC
Power Consumption
12VDC:1.6w max./ 24VAC:
1.7w max.
12VDC:3.7w max./ 24VAC: 3.5w
max.
Operating Temperature
-10°C~50°C / 14°F~122°F
Humidity
20%~80%
Dimensions(in/mm)
133 x 96mm / 5.24 " x 3.78"
Weight(lbs/g)
0.65lbs /295g
0.79lbs /360g
Certifications
CE/FCC/RoHS
5. Specifications
Specifications and designs are subject to change for improving the functionality of this product
without notice.
17
Page 18
ED910/930 eZ.HD Indoor Dome Camera
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
sales@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
EverFocus China - Shanghai:
Room 403, Ruijin Business Center, No.96, Zhaojiabang
Road, Luwan district, Shanghai 200020, China
TEL: +86 21 6471 2229 / 6471 2291
FAX: +86 21 6471 0566
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus India:
UBS, 629/1243, 1st Floor, G Block, Behind
Teacher’s Colony, Bandra Kurla Complex,
Bandra (E), Mumbai 400 051, India
TEL: +91 22 6726 4500
FAX: +91 22 6726 4518
www.everfocus.in
sales@everfocus.in
Your EverFocus product is designed and
manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed
ofseparately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
EverFocus Electronics Corp.
Loading...