EverFocus ECOR264-D2 User Manual
User Manual
ECC
E
O
R226644--
O
R
D22
D
DVV
D
R SSeerriieess
R
EVERFOCUS ELECTRONICS CORPORATION
ECOR264-D2 DVR Series
Instruction Manual
2010 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the Everfocus Electronics Corporation.
Release Date: September 2010
QuickTime is a registered trademark of the Apple Computer, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.
Safety Precautions
Refer all work related to the installation of this product to qualified service personnel or system
installers.
Do not block the ventilation openings or slots on the cover.
Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the
power off immediately and contact qualified service personnel for service.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or
covers. There are no user-serviceable parts inside. Contact qualified service personnel for
maintenance. Handle the appliance with care. Do not strike or shake, as this may damage the
appliance.
Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take immediate
action if the appliance becomes wet. Turn the power off and refer servicing to qualified service
personnel. Moisture may damage the appliance and also may cause electric shock.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean
the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.
Do not overload outlets and extension cords as this may result in a risk of fire or electric shock.
Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do
not use the appliance in an extreme environment where high temperature or high humidity exists. Use
the DVR at indoor type temperatures within 0°C~40°C (32°F~104°F) and at relative humidity between
20%~80%. The input power source for this device is 12VDC though a power supply which operates
from100~240VAC.
Read Instructions
All the safety and operating instructions should be read before the unit is operated.
Retain Instructions
The safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the unit and in the operating instructions should be adhered to.
Follow Instructions
All operating and use instructions should be followed.
Cleaning
ii
y
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners, abrasive or aerosol
cleaners. Use a damp cloth for cleaning
Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Water and Moisture
Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is
classified as a wet location.
Servicing
Do not attempt to service this unit by yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, playing particular attention to cords and plugs, convenience receptacles,
and the point where they exit from the appliance.
Object and Liquid Entry
Never push objects of any kind into this unit through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the
unit.
ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in
this case, the user ma
be urged to take adequate measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures :
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the users’ authority to operate this equipment.
iii
WEEE
This Product is RoHS compliant.
The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.
Therefore, all specifications are subject to change without prior notice. Manufacturer is not responsible for misprints or typographical
errors.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
iv
TABLE OF CONTENTS
1 PRODUCT OVERVIEW ..................................................................................................... 1
1.1 FEATURES....................................................................................................................... 1
1.2 PACKAGE CONTENTS................................................................................................... 2
1.3 SPECIFICATIONS ........................................................................................................... 3
1.4 FRONT PANEL ................................................................................................................4
1.5 REAR PANEL................................................................................................................... 6
1.6 VIDEO INPUTS/OUTPUTS INSTALLATION............................................................... 8
1.7 AUDIO INSTALLATION ................................................................................................8
1.8 ALARM CONTACTS INSTALLATION......................................................................... 8
1.8.1 Alarm Input Contacts..............................................................................................................................8
1.8.2 Alarm Output Relay.................................................................................................................................9
1.9 RS-485 KEYBOARD / PTZ INSTALLATION........................................................................... 9
1.9.1 General RS-485 bus installation .............................................................................................................9
1.9.2 RS-485 socket pin assignment...............................................................................................................11
1.9.3 EKB-500 connection with network patch cable.....................................................................................11
1.9.4 EKB-500 connection to several DVRs...................................................................................................11
1.9.5 Speed Dome Installation .......................................................................................................................11
1.10 USB-MOUSE INSTALLATION.......................................................................................... 12
1.11 NETWORK CONNECTION........................................................................................ 12
1.11.1 Direct PC Connection through Crossover Network Cable ...................................................................12
1.11.2 Network Connection through Patch Cable............................................................................................13
1.12 FINAL INSTALL PROCESS....................................................................................... 13
2 MOUSE AND FRONT PANEL OPERATION ............................................................... 14
2.1 GENERAL USB MOUSE OPERATION....................................................................... 14
2.1.1 How to select a channel / Enable audio................................................................................................14
2.1.2 OSD Root Menu.....................................................................................................................................14
2.1.3 Operation in the Configuration Menus.................................................................................................15
2.1.4 Field Input Options ...............................................................................................................................15
2.2 G
2.2.1 How to select a channel / Enable audio................................................................................................17
2.2.2 OSD Root Menu.....................................................................................................................................17
2.2.3 Front Panel Key Review........................................................................................................................17
2.2.4 Operation in Configuration Menu.........................................................................................................17
2.2.5 Field Input Options ...............................................................................................................................18
ENERAL FRONT PANEL OPERATION ...............................................................................17
3. GENERAL DVR OPERATIONS...................................................................................... 20
3.1 RECORD......................................................................................................................... 20
3.2 LOGIN............................................................................................................................. 20
3.3 SELECT CAMERA OPERATION................................................................................. 21
3.5 PLAYBACK.................................................................................................................... 22
v
3.6 PTZ.................................................................................................................................. 23
3.6.1 General PTZ control (if PTZ cameras are installed)..................................................................................23
3.6.2 Express Control of PTZ.........................................................................................................................24
3.7 LAYOUT......................................................................................................................... 26
3.7.1 Bring a camera to full screen mode.......................................................................................................26
3.8 CHANNEL
SWITCHING............................................................................................... 26
3.9 DISPLAY ........................................................................................................................ 27
3.10 SEQUENCE.................................................................................................................. 27
3.11 ZOOM........................................................................................................................... 27
3.12 SEARCH....................................................................................................................... 29
3.12.1 Time Search...........................................................................................................................................29
3.12.2 Event Search..........................................................................................................................................30
3.12.3 Smart Search .........................................................................................................................................31
3.12.4 Snapshot Search ....................................................................................................................................34
3.13 COPY............................................................................................................................ 35
3.14 LOGOUT...................................................................................................................... 36
4 DVR CONFIGURATION .................................................................................................. 37
4.1 CONFIGURATION MENU............................................................................................ 37
4.2 EXPRESS........................................................................................................................ 37
4.3 CAMERA SETTING ...................................................................................................... 40
4.3.1 Basic Setting..........................................................................................................................................40
4.3.2 Video Adjust ..........................................................................................................................................43
4.3.3 Motion ...................................................................................................................................................44
4.3.4 Video Loss.............................................................................................................................................47
4.4 RECORD & PLAY SETTING........................................................................................ 48
4.4.1 Record...................................................................................................................................................48
4.4.2 Built-in Calculator ................................................................................................................................49
4.4.3 Play .......................................................................................................................................................50
4.5 ALARM & EVENT SETTING....................................................................................... 51
4.5.1 Alarm .....................................................................................................................................................51
4.5.2 Event......................................................................................................................................................53
4.6 SCHEDULE
4.6.1 Express Setup .......................................................................................................................................60
4.6.2 Holidays ................................................................................................................................................61
4.6.3 Schedule ................................................................................................................................................62
4.6.4 Alarm Action .........................................................................................................................................68
SETTING................................................................................................... 60
4.7 NETWORK SETTING.................................................................................................... 72
4.7.1 LAN .......................................................................................................................................................72
4.7.2 EMAIL...................................................................................................................................................74
4.7.3 DDNS ....................................................................................................................................................75
4.7.4 Alarm Server .........................................................................................................................................77
4.8 DISK
4.8.1 Disk .......................................................................................................................................................78
INFORMATION................................................................................................... 78
4.9 DISPLAY SETTING....................................................................................................... 79
4.9.1 Monitor OSD.........................................................................................................................................79
4.9.2 Main M/T SEQ ......................................................................................................................................80
4.10 SYSTEM SETTING..................................................................................................... 81
4.10.1 Date/Time..............................................................................................................................................81
vi
4.10.2 Daylight Saving.....................................................................................................................................82
4.10.3 User.......................................................................................................................................................83
4.10.4 I/O Control ............................................................................................................................................86
4.10.5 Misc. ......................................................................................................................................................87
4.11 INFORMATION........................................................................................................... 89
4.11.1 System....................................................................................................................................................89
4.11.2 Log.........................................................................................................................................................90
5 NETWORKING OVERVIEW .......................................................................................... 92
5.1 INTRODUCTION TO TCP/IP............................................................................................... 92
5.2 S
5.3 G
UBNET MASKS................................................................................................................ 92
ATEWAY ADDRESS......................................................................................................... 92
5.4 VIRTUAL PORTS................................................................................................................ 93
5.5 PRE-INSTALLATION .......................................................................................................... 93
5.6 WHAT IS YOUR NETWORK SETUP?.................................................................................... 94
5.7 SIMPLE ONE TO ONE CONNECTION................................................................................... 95
5.8 DIRECT HIGH SPEED MODEM CONNECTION ................................................................... 100
5.9 ROUTER OR LAN CONNECTION...................................................................................... 102
6 REMOTE OPERATION FROM BROWSER.................................................................... 105
6.1 CONNECTING TO ECOR264 D2.................................................................................... 105
6.2 BROWSER SECURITY SETTING .................................................................................. 106
6.2.1 Installing ActiveX controls..................................................................................................................106
6.2.2 Enabling ActiveX Controls..................................................................................................................109
6.3 REMOTE LIVE VIEW................................................................................................. 112
6.4 REMOTE PLAYBACK................................................................................................ 114
7 EVERFOCUS DDNS SETUP .......................................................................................... 115
8 LINKSYS & D-LINK PORT FORWARDING ............................................................. 117
8.2 TYPICAL LINKSYS PORT FORWARDING............................................................. 117
8.3 TYPICAL
9 TROUBLESHOOTING
D-LINK PORT FORWARDING ................................................................ 119
................................................................................................... 122
APPENDIX A: TIMING OF ALARM MODES.................................................................... 124
APPENDIX B: EXPRESS SETUP RECORDING VALUE SELECTION RULES
.......... 127
APPENDIX C: REMOTE CONTROL................................................................................... 129
vii
Chapter
1
1 PRODUCT O VERVIEW
The introduction of the ECOR264 D2 series adds the advantages of H.264 compression to the power and
flexibility of the already popular ECOR DVR. State of the art H.264 compression techniques enhance
recorded video storage capacity and conserve network transmission bandwidth while maintaining high
image quality. Both the 4 and 8 camera models are capable of real time recording (4x30FPS@2CIF,
8x30FPS@CIF). Plus, the ability to independently configure image resolution and frame rate for
individual cameras allows some cameras to be recorded at D1 while others are set at CIF or 2CIF to
utilize the entire 240 CIF FPS recording capacity of the unit.
The new enhanced color Graphical User Interface (GUI) makes configuration over the network, from the
front panel or with the included mouse fast and easy. An Express Setup option allows rapid configuration of
time & date, global recording settings and network configuration from a single screen. Choose from
continuous, event or schedule recording, or pick the number of days you want to record and the Express
Setup does the rest. View live, play back recorded video and configure the DVR remotely over a LAN or
WAN with the included web browser interface; check your home or business on the go from a cell phone or
PDA – the ECOR264 D2 series supports multiple remote access methods.
On playback, in addition to traditional date/time and event searches ECOR264 D2 series also provides
powerful Smart and Snapshot Search functions. Review recorded video and let the DVR identify motion in
area(s) of interest during playback, or choose a starting date/time, an interval and direction and view a
series of snapshots extracted from recorded video to quickly isolate and play back relevant video for
efficient review of significant activities.
1.1 FEA TU RES
- Compatible with FREE EverFocus Central Management Software
-H.264 Compression format for efficient disk utilization and network bandwidth conservation
-Recording resolution and rate can be set independently for each camera, and changed via user defined
schedule
-Streaming at CIF for remote web viewing to conserve bandwidth
-Pentaplex Operation (Simultaneous live, recording, playback, archiving and remote viewing)
-Free EverFocus DDNS Service - static IP address is not
-User friendly color GUI with graphical icons and visual indicators
-Supports mobile monitoring of live video from PDA and Smart Phones
-Multiple Control Inputs: mouse/front panel/IR remote controller/EKB500 keyboard
-Built-in record time calculator for fast recording estimation
required for reliable remote access
1
-Express Setup: A unique menu option for quick & easy installation and setup
-Express Archive: Archive video instantly (to USB) while playing back
-Express Playback: Simply point, click and drag the playback bar to view desired recordings
-Express Search: Use the intuitive playback bar with simple drag & drop operations
-Smart Search: Review recorded video to identify motion in area(s) of interest
-Snapshot search: choose an interval and direction, view a series of snapshots to quickly isolate incidents
-Remote viewing of live and recorded video, plus configuration support from the built-in web interface
-On-screen PTZ control via mouse or front panel
-Built-in DVD burner (-“D” Models)*
-2 USB 2.0 ports (1 located on front panel, 1 located on back panel) for video archive and mouse usage
-Multi-language support
-USB Mouse and IR remote control included
*Feature may not be available on all models
1.2 PA CKA GE CONTENTS
-Digital Video Recorder x1
-User Manual x 1
-AC Adapter x 1
-Mouse x 1
-Terminal Block x 6
-IR Remote Control x 1
-Battery x 2
-HDD Fixing Bracket x 1 set
-Power Cord x 1
-SATA cable x 1
-Screws x 4 for HDD
-Screws x 2 for HDD fixing bracket
-Shockproof rubber x 4
2
1.3 SPECIFICA TIO NS
ECOR264-4/8D2
Channel Number 4 8
Compression Format H.264
Recording Rate/Resolution
*Total = 240 FPS @ CIF; per camera
resolution & FPS rates can be set
independently up to the total capacity
Playback Rate/Resolution
Playback up to full record rate.
60 NTSC / 50 PAL (D1)
120 NTSC / 100 PAL (Half D1)
120* NTSC / 100 PAL (CIF)
60 NTSC / 50 PAL (D1)
120 NTSC / 100 PAL (Half D1)
120 NTSC / 100 PAL (CIF)
60 NTSC / 50 PAL (D1)
120 NTSC / 100 PAL (Half D1)
240 NTSC / 200 PAL (CIF)
60 NTSC / 50 PAL (D1)
120 NTSC / 100 PAL (Half D1)
240 NTSC / 200 PAL (CIF)
Dual Streaming 120 NTSC/100 PAL(CIF) 240 NTSC/200 PAL(CIF)
Mobile View Live view on PDA or Smart Phone plus various web browsers
Pentaplex Operation Simultaneous Live, Recording, Playback, Archive and Remote
Viewing
Video Inputs 4 BNC 8 BNC
Main Monitor Output VGA or BNC output; selectable from front panel
Audio Input/Output (RCA) 1 Input / 1 Output
Recording Modes Manual, Schedule and Event; or, Set Number of Days
Playback Search Date/Time, Event, Motion in Recorded Video, Snapshot by Interval
Alarm Inputs 4 8
Alarm Outputs 1 Alarm Output (form “C” – rated: 12VDC @ 1A)
Video Pause Yes
Video Loss Detection Yes
Motion Detection Yes
Event Log Yes
Watch Dog Timer Yes
Internal HDD 1 Internal SATA HDD
Built-in DVD Burner Slim Type DVD Burner(Optional –“D” Model)
User Interface GUI(Color Graphical User Interface)
OS Embedded Linux
Network/Protocol 10/100Mbps Ethernet; TCP-IP / DHCP/ PPPoE / DDNS
Control PTZ via OSD Yes
USB 2 USB 2.0 ports (1 on Front Panel, 1 on Back Panel)
Schedule Setting Express and Advanced Schedule Setting Tools
User Access 3 Levels of User Access Supported
RS-232 Yes (future use)
RS-485 1 RS485 (3 Terminal connector)
Power Source DC12V (from included 110/220VAC power supply)
Temperature 0°C~40°C / 32°F~104°F (20~80% humidity)
Certificates CE, FCC
Supported PTZ Protocols EverFocus, Pelco D, Pelco P, Samsung, Transparent
3
1.4 FRONT PANEL
Your primary interaction with your new DVR will be through the Front Panel buttons and their
corresponding buttons on the included IR Remote Control. Take a moment to learn where the keys are as
the remainder of the manual will refer to them often.
○
6
○
3
2
○
○
1
○4
5
○
○7
15
○
16
○
17
○
18
○
8
○
9
○
10
○
11
○
○12
13
○
14
○
Figure 1-1 Front Panel
1) DVD+RW: DVD+RW burner for DVD model. (D models only)
2) ◄◄/◄I : Fast reverse playback or step reverse playback depending on playback mode.
3) ◄/ II: Reverse playback or pause
4) ►/ II: Forward playback or pause
5) ►►/I►: Fast Forward playback or step forward playback depending on playback mode.
6) Enter/ Arrow keys: Instead of or in combination with a mouse, you can use these keys to change
the Menu settings.
7) Menu/ESC: Press this key to enter/exit MAIN SETUP MENU.
8) USB 2.0 (front): For connecting USB-Flash-Drive to copy/archive video or for firmware upgrades.
9) Channel keys 1~8 (1~4):
4
1
○
Press channel key (CH1~CH8) / (CH1~CH4) to display that channel in full screen view.
2
Press channel key again for 2x electronic zoom. Zoom screen can be moved through arrow keys.
○
Pressing the channel key again switches the electronic zoom off and return to full screen view of
that channel.
10) Live: Press this key to show live view. Press to exit from playback mode.
11) View: Press this key to switch between 4x, PiP (Picture In Picture), full screen and 9x.
Note: ○
1
PIP display is not available in playback mode.
○2 This key is also used for BNC and VGA selection at the initial setup.
12) SEQ: Press this key to enter the auto sequential switching mode. The sequence dwell time can be
set in “Display Setting” tab of the Menu. For more detail about SEQ, please see “Section 4.9.2
Display Setting-Main M/T SEQ”
13) Search: Press this key to enter Search Menu. For more detail about the Search function, please
see “Section 3.12 Search”.
14) Copy: Press this key to enter Copy Menu. For more detail about Copy function, please see
“Section 3.13 Copy”.
15) Power LED: This LED ON indicates Power on.
16) Alarm LED: This LED ON indicates Alarm active.
17) HDD LED: This LED ON indicates HDD active.
18) Network LED: This LED ON indicates Network active.
5
1.5 REAR PANEL
During initial setup you will be connecting your DVR to multiple input and output devices. This is done
through the rear panel.
4
○
1
○
2
○
3
○
9
○
1
○
Alarm In: Connect up to 4/8 alarm inputs, selectable between N.O./N.C. contacts.
10
○
11
○
Figure 1-2 Rear Panel
5
○
○
6
○
12
7
○
8
○
2
○
Alarm Out: N.C or N.O type alarm out (form “C”).
3
○
Audio In: Connect line level output of an audio preamplifier to the audio input connection
corresponding to the appropriate camera.
4
Video In: Connect camera’s video output or other composite video source to the video input
○
connection.
5
○
Video Out: Looping Outputs - connect the camera video signals to other equipment as required.
6
○
RS232 socket: 9-pin D-Sub control input for RS-232.
7
USB 2.0: USB port recommended for connecting the USB mouse.
○
8
○
LAN: RJ-45 network connection 10/100 Mbps Ethernet. There are two LEDs on the LAN jack;
Green LED means network is connected, amber LED flickers when data is being
exchanged.
9
POWER: Plug the DC 12V power source provided into the power socket.
○
6
10
○
RS485 socket: For remote control via RS-485 keyboards and telemetry control for attached PTZ
devices
11
○
Audio Out: Connect to the line level input of an audio amplifier.
12
○
VGA: Connect a VGA monitor to the VGA output connection. VGA resolution is 1280x1024.
7
1.6 VIDEO INPUTS/OUTPUTS INSTALLA TION
Cameras and CCTV monitors must use copper center conductor/copper braid 75 Ohm video cable (e.g.
RG-59, RG-6, RG-11) with BNC connectors.
To avoid impedance mismatch and undesired loss/reflections, 50 Ohm coax cable (e.g. RG-58), or 75 ohm
foil shield antenna cable and other types of coaxial cable are not compatible.
All connected video sources must provide a 1 Vpp NTSC or PAL standard video signal.
When converting other transmission types (twisted pair, fiber optics, radio) for the video inputs, be sure to
verify accurate receiver calibration and signal levels.
ATTENTION: In order for the system to auto-detect the appropriate video format (NTSC or PAL), make
sure that there is a video signal on video input 1 upon power-up.
1.7 AUDIO INSTALLA TION
This DVR provides 1 line level audio input and 1 line level audio output.
ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone
amplifier is required). The audio output requires an amplifier to drive a speaker or headphones.
The installation must be connected with audio coax cable and RCA plugs.
AUDIO RECORDING FUNCTIONALITY:
Audio recording is activated / deactivated in the Camera Menu for Camera #1. Please check and always
comply with local laws and regulations when using audio recording.
The audio channel is always recorded together with video and is independent of the image recording rate.
1.8 ALARM CONT A CTS INSTALLA TION
The alarm input can be used to start recording or for recording rate adjustment. In addition, alarm reactions
such as camera display on the monitor, buzzer, e-mail and network alarm are available. The alarm output
relay can be switched if required. Alarm input response actions can be controlled according to a flexible
schedule.
1.8.1 Alarm Input Contacts
This DVR provides one alarm input per camera. The input is programmable N.O. (Normal Open) or N.C.
(Normal Clos
ed) Input has to be switched by dry contacts.
8
Alarm input with N.O. (Normal Open) contact Alarm input with N.C. (Normal Closed) contact
in idle state in idle state
All settings are programmed in the ALARM menu (Section 0).
1.8.2 Alarm Output Relay
The relay output provides either Normally Open or Normally Closed dry contacts.
Output relay in idle state
1.9 RS-485 keyboard / PTZ Installation
All functions can be remote-controlled by the EKB-500 universal keyboard. Using the EEPbus protocol,
digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One
system can comprise up to 8 keyboards.
1.9.1 General RS-485 bus installation
The EKB-500 keyboard uses a RS-485 simplex wiring; the signal is transferred via a single twisted pair line.
CAT5 network cable is recommended, UTP version (unshielded) is sufficient for normal applications. A
shielded cable should be used if the installed cables are expected to be highly susceptible to interference.
The number of devices installed in one bus is limited to 32, and the maximum cable length is 3,900 feet.
Both of these can be expanded using a signal distributor EverFocus Model EDA997A (see below).
Both the first and the last device in series should be terminated with 120 Ohm resistance in order to
minimize line reflections.
RS-485 bus serial wiring
Cable length from box to device („Stubs“) has to be limited to 2m using connector boxes.
9
RS-485 bus serial wiring with connector boxes and connection cable
Direct RS-485 bus star wiring is not supported unless using an EverFocus Model EDA997A (see below).
Improper RS-485 bus star wiring
An EDA997A RS-485 signal distributor may be used to use a star wiring configuration.
Star wiring with RS-485 signal distributor
A RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as
the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an
additional 1200m, and it also enables the additional connection of 31 further devices to each output (the
output itself represents one device).
The maximum system expandability depends on the RS-485 address range of the installed devices.
System expansion with RS-485 signal distributor
10
ATTENTION: EDA997A signal distributors are unidirectional! This means that the signal only flows from
the input towards the outputs. Therefore, e.g. the interconnection of several keyboards is not possible with
these types of signal distributor!
1.9.2 RS-485 socket pin assignment
The RS485 pin assignment is as follows:
+
I
1.9.3 EKB-500 connection with network patch cable
For a simple, short distance installation, recorder and keyboard can be connected directly using a standard
CAT5 network cable with an 8-pin connector at only one end, and at the other end the Pin 3 wire connected
to RS485 “+” (plus) and the pin 6 wire connected to RS-485 “-“ (minus).
1.9.4 EKB-500 connection to several DVRs
For long distance installations connecting several DVRs, please use an EDA997A signal distributor to
connect. For further details on keyboard connection, please refer to the EKB-500 manual.
RS-485 port communication settings are configured in the I/O CONTROL menu (Section 5.10.4 System
Setup: I/O - control).
1.9.5 Speed Dome Installation
Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional
PowerCon software if the DVR is connected to a network. Local telemetry control is provided by USB mouse control or by the optional EKB-500 keyboard.
Supported protocols: EverFocus, Pelco-D, Pelco-P, Samsung, Transparent
Required DVR settings: RS-485 receiver address in CAMERA menu
(Section 4.3)
RS-485 parameters and protocol in the I/O CONTROL menu
(Section 5.10.4)
ATTENTION: Some Pelco-
D / -P protocol domes and receivers require an address offset of -1, i.e. the
address assigned to the dome / receiver in the DVR camera menu must be 1 below the address set in the
dome / receiver itself!
11
1.10 USB-Mouse installation
Connect the USB mouse to one of the 2 USB ports. (This can be done while DVR is powered on) The rear
USB V1.0 port is recommended to reserve the higher speed front USB V2.0 port for video copy/export.
NOTE: Recommended mouse types are Logitech® and Microsoft® wired USB wheel-mouse. Wireless
USB mouse is not supported.
1.11 NETWORK CONNECTION
This section only describes physical connection to an Ethernet network. This step must be completed
before the DVR can connect to the network. There are two basic types of connection:
1.11.1 Direct PC Connection through Crossover Network Cable
The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of
connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a
10/100 Mbps compatible network connection.
Figure 1-3 Direct PC Connection
Pinout of crossover-cable
12
1.11.2 Network Connection through Patch Cable
The connection to an existing network requires a normal patch cable (straight-through). The illustration
shows the connection to a network switch or router.
Figure 1-4 Network Connection through Patch Cable
Pinout of straight patch cable
1.12 FINAL INSTALL PROCESS
Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in
the power source. The POWER LED will light up if power is normal. Once the system has finished loading,
you can begin to set up the menu options for the DVR.
13
Chapter
3
2 MOUSE AND FRONT PANEL OPERATION
ECOR264 D2 DVRs support multiple sources to control the DVR. It can be controlled with a mouse, the
front panel, an EKB500, and the handheld IR remote control.
This chapter will cover the basic operation using the mouse and the front panel buttons.
2.1 GENERAL USB MOUSE OPERA TION
2.1.1 How to select a channel / Enable audio
1. In a view consisting of more than one channel, users can select a channel by clicking once on the
desired channel screen. The selected screen will be highlighted by a white frame.
2. Double clicking on a channel screen will display full screen for this channel.
3. To enable audio out, click the audio icon (ex: ) at lower side of the screen. This system has only
one audio out. Click this button to enable or disable the audio-out mode.
2.1.2 OSD Root Menu
1. Right-click the mouse to obtain the DVR menu bar (see Figure 2-1 OSD Root Menu ). When you move
the mouse over each icon, its title will be displayed at the top of the control bar.
Figure 2-1 OSD Root Menu
2. Click on any icon to perform that action. These actions are covered in detail in Chapter 3.
3. Click the “X” in the top-right corner to close the DVR control bar.
14
2.1.3 Operation in the Configuration Menus
Click on the icon to access the Configuration Menu.
The Configuration menu screens (shown in Figure 2-2 OSD Menu) are divided into 3 main sections.
1
2
3
Figure 2-2 OSD Menu
1. In section 1, there are ten setup options available. Move the mouse over an icon and click to select it.
2. In section 2, the choices for the selected icon will be displayed. Click on a choice to select it.
3. In section 3, all the options for the selected choice will be available. Click on a field to make changes.
2.1.4 Field Input Options
The following are examples of different types of fields available in the Configuration menu.
Textbox: Click on the box and an on-screen keyboard will appear*. (see
note about the on-screen keyboard below)
Dropdown box: Click on the down arrow to see all selections, then
directly click on an option to select it.
Check box: Click on the box to enable it (checked) or disable it (unchecked).
15
Button: Click the button to execute the function.
Bar: Click and hold on the bar to adjust the set point Left or Right.
* Note about on-screen keyboard:
Click on a button to input that character.
The buttons on the right and bottom have the following functions:
Space Enter a space
Caps Switch to capital letters
Delete the letter
Confirm the selection
Move to right
Move to left
16
2.2 General Front Panel Operation
2.2.1 How to select a channel / Enable audio
1. In a view consisting of more than one channel, press the arrow keys (Up/Down/
Right/Left) to scroll
through each channel that is displayed. The selected channel will be highlighted by white frame.
Pressing the “left” or “right” arrow when the last/first camera (1,4 or 8) is highlighted will select all
cameras.
2. While channel #1 is selected, press the “Enter” button to turn Audio On/ Off.
2.2.2 OSD Root Menu
1. Press “Me
nu” key to display the DVR menu bar. Use the left/right arrows to scroll over each icon. The
title for each icon will be displayed on top of the menu bar.
2. Press “Enter” key on any icon to perform that action. These actions are covered in detail in Chapter 3
3. Press “Menu” to close the DVR menu bar.
2.2.3 Front Panel Key Review
The basic principle of front panel operation is to use arrow keys to navigate among the menu items. Use
the “Enter” key to confirm a selection or enter the next level menu. Press the “Menu” key to enter the Main
Menu or exit from the current level of the menu.
2.2.4 Operation in Configuration Menu
Press “Menu”, use the arrow keys to highlight the “Configuration” icon, and press “Enter” with
“Configuration” icon highlighted to bring up the Configuration menu.
NOTE: If the require password option is active, you will need to log in first. Refer to “Section 3.2 LOGIN” for
information on logging in. The menu (shown in
Figure 2-3 OSD Menu ) is divided into 3 main sections.
17
Loading...