1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity between 20%~ 80%; this device is not rated as
submersible. The input power source is 12VDC ONLY. Be sure to connect the proper + / -
polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera
to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.
2
Page 3
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Get incredible performance in bright light or low light, and the resolution listed in the specs from
the actual camera you install. To take full advantage of the amazing resolution available from this
advanced imaging technology, the EverFocus eZ.HD Series ECD900 uses a 3.6mm lens together with
1/2.8" SONY 1.37M pixels CMOS to deliver 720p high resolution. Combined with a useable native
low light sensitivity of 0.08lux without using digital slow shutter, this camera truly provides HD
images without compromising its 720p video quality, Digital Wide Dynamic Range for clear color
images in the most challenging of bright or unbalanced scene lighting conditions, plus true
day/night in low light with guaranteed ZERO ghosting. The ECD900 with its 3 Axis rotation design
allows wall or ceiling mounting. This is the camera that you have been waiting for to create analog
CCTV systems that produce astounding image clarity in a wide range of indoor applications at the
widest range of light levels. The ECD900 supports both NTSC and PAL scanning systems, which can
be switched via OSD.
1.1 Packing List
1.2 Features
720p with high flexibility and performance for astounding image
1/2.8" SONY 1.37M pixels CMOS, delivers amazing high sensitivit
D-WDR to improve the visibility under high contrast scene
Provides 3D- Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments
Support 720p & 960H analog signal output, which can be easily switched by OSD
Easy lock installation by screwing the base plate to the surface and then locking the
camera to the base plate without mounting screws
5
Page 6
ECD900 eZ.HD Mini Dome Camera
No.
Name
Descriptions
1
Power Cable
Connect to a 12VDC.
2
Dual Video Output
720p and 960H output, using a 75 Ohm BNC-type coaxial cable.
3
DC Power Pigtail Cable
Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).
2. Cable Description
6
Page 7
ECD900 eZ.HD Mini Dome Camera
3. Installation
3.1 Installation and Adjustment
1. Stick the Template Plate on the position where you want to attach the camera.
2. Drill the three holes on the template for screwing the camera with the supplied screws
and anchors, and the circle in the middle only if you want to wire the cables through the
wall / ceiling.
3. Insert the supplied anchors into the holes.
4. Remove the Camera Cap from the Camera Body.
5. Attach the camera body to the correct position and then screw the camera body to the
wall / ceiling using the supplied three screws.
7
Page 8
ECD900 eZ.HD Mini Dome Camera
6. Connect the camera to the 12VDC power source and an AHD DVR or monitor.
7. Configure the OSD Menu, using the function button.
Note: The function button is not only for direction control, but also for switching Video
format and Video output. Please follow the detailed instruction as below:
Press the "down" button key over 5s to switch video format from PAL to NTSC.
Press the "left" button key over 5s to switch video output from 720p to 960H
(720p is the default).
Press the "right" button key over 5s to switch video output from 960H to 720p.
8. Adjust the camera angles, simply tilt, pan or rotate the camera.
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed ofseparately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
EverFocus Electronics Corp.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.