Euro-Pro IR412 User Manual

Model IR412

EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase. The liability of EURO-PRO
Operating LLC is limited solely to the repair or replacement of the product at EURO-PRO’s option.
This warranty does not cover damage caused by misuse, negligence, use on improper current or
voltage, use contrary to operating instructions or disassembly, repair or alteration by any person
other than EURO-PRO Operating LLC.

Product repair or replacement, at our option, is your sole remedy. This warranty excludes all other
legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC, if any, is
limited to the specific obligations expressly assumed by it under the terms of the limited warranty.
In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any
nature whatsoever. Some States do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you. This warranty gives you specific
legal rights which vary from state to state.

If you have a claim under this warranty or if you require service

DO NOT RETURN THIS PRODUCT TO THE STORE!

Send the product , postage prepaid to: In U.S.A.: EURO-PRO Operating LLC

Please include a copy of your sales receipt, $9.50 to over the cost of return shipping &
handling and a letter explaining the nature of your difficulty. Do not forget to enclose your
name, address and telephone number.

If the warranty period has expired, please send your iron postage pre-paid to:

In U.S.A.: Service Department

You will be advised of the cost of repair before any servicing is done unless you enclose a
note indicating that you would like us to proceed with the repairs and return the iron to you
C.O.D.

LIMITED WARRANTY

21 Lawrence Paquette Ind. Dr.
Champlain, NY 12919
Tel: [phone]

EURO-PRO Operating LLC

21 Lawrence Paquette Ind. Dr.
Champlain, NY 12919
Tel: [phone]

OWNER’S MANUAL
Retractable Cord Iron

Model IR412
1400 Watts

PRODUCT REGISTRATION CARD

Please complete and return within ten (10) days of purchase. The registration will enable us to
contact you in the event a product defect is discovered. By returning this card you acknowledge
to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.

RETURN TO: EURO-PRO Operating LLC, 21 Lawrence Paquette Ind. Dr., Champlain, N.Y. 12919

PURCHASER: ……………………………………………………………………………………………

ADDRESS: ……………………………………………………………………………………………….

DATE OF PURCHASE: …………………….. MODEL: ………………. SERIAL NO: .…………….

NAME AND ADDRESS OF STORE: …………………………………………………………………..

Printed in China

Model IR412

For information or assistance:

USA: EURO-PRO Operating LLC

21 Lawrence Paquette Industrial Drive
Champlain, NY 12919
Tel.: [phone]

IMPORTANT SAFETY INSTRUCTIONS

TROUBLESHOOTING

When using your iron, basic safety
precautions should always be followed,
including the following:

1. Read all instructions carefully.

2. Use iron only for its intended use.

3. To protect against risk of electrical
shock, do not immerse the iron in
water or other liquids. Always turn
the iron to “OFF” before plugging in
or unplugging from outlet.

4. Never yank cord to disconnect from
outlet. Grasp plug and pull to
disconnect.

5. Do not allow cord to touch hot
surfaces. Let iron cool completely
before putting away.

6. Always disconnect iron from
electrical outlet when filling with
water, emptying, or when not in use.

7. Do not operate iron with a damaged
cord, or after the iron has been
dropped or damaged in any manner.
To avoid the risk of electric shock,
do not disassemble the iron. Return
the iron to EURO-PRO Operating
LLC for examination and repair.
Incorrect reassembly can cause the

risk of electric shock when the iron is
used.

8. Close supervision is necessary for
any appliance being used by or near
children. Do not leave iron
unattended while connected or on an
ironing board.

9. Burns can occur from touching hot
metal parts, hot water or steam. Use
caution when you turn a steam iron
upside down; there may be hot
water in the reservoir.

10. This appliance is for household

use only.

11. Hold the plug when rewinding the
cord. Do not allow the cord to
whip

when rewinding.

SPECIAL INSTRUCTIONS

1. To avoid a circuit overload, do not
operate another high-wattage
appliance on the same circuit.

2. If an extension cord is absolutely
necessary, use a 13-ampere cord.
Cords rated for less amperage may
overheat. Use care to arrange the
cord so that it cannot be pulled or
tripped over.

POLARIZED PLUG: This appliance has a polarized plug (one blade is

wider than the other). As a safety feature, this plug
will fit into a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician. Do no attempt to defeat this safety
feature.

SAVE THESE INSTRUCTIONS

For Household Use Only

Rev. 06/02A1

PROBLEM POSSIBLE REASONS & SOLUTIONS

• Iron should be plugged into a 120V AC electrical

Iron does not heat

Thermostat ready light
goes On and Off

Some odor or small
particles come out of
steam vents of new
iron

Iron does not steam

Water droplets coming
from steam vents

outlet only.
Make sure that the plug is securely in the socket.

• Temperature setting too low.
Turn to higher setting.

• This is normal.
The light goes On and Off as the thermostat is
switching the heating element On and Off to
maintain the selected temperature.

• This is normal.

Follow instructions for first use and allow iron to steam
through 2-3 fillings & press the steam burst button
occasionally to eliminate small white particles.

• Water tank may be empty or water level is very low.

Add water.

• Make sure that the temperature control dial and

the variable steam control are correctly set. For
maximum steam, (setting ‘Max’ on steam control),
temperature control dial should be set on ‘•••’.

• Adjustable steam control is set on “0”.

Always allow the iron to reach the selected
temperature with the adjustable steam control setting
at ‘0’. Make sure the temperature control dial is set in
the correct steam area, e.g. ‘•’, and the steam control is
not

on ‘0’. For more steam, turn temperature dial to

higher setting, e.g. ‘•••’, and the steam control to ‘Max’.

• If temperature setting and steam control setting are

correct and there is no steam, gently
soleplate on the ironing board a few times. Move
the variable steam control from ‘0’ to ‘Max’ a few
times.

• Iron may not be hot enough. Set thermostat to the

‘Max’ position. Always allow iron sufficient time to
heat up (thermostat light goes off) before activating
the variable steam control.

• Overuse of steam burst. Allow more time between

each burst.

• Iron may have been overfilled. Turn iron off,empty

water and follow instructions for filling.

• Steam performance may be low if iron requires

seasoning. To season, use regular tap water for 1or 2
tanks until steam performance improves.

10

tap the