GARBAGE CAN & CENTRAL VAC SYSTEM
OWNER’S MANUAL
Model: GC130HS
120 V. 60 Hz., 12 Amps.
COPYRIGHT © EURO-PRO OPERATING LLC 2006
U.S.: 94 Main Mill Street, Door 16 Canada: 4400 Bois-Franc
EURO-PRO Operating LLC
Plattsburgh, NY 12901 St-Laurent, QC H4S 1A7
Tel. : 1 (800) 798-7398
Model GC130HS
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized
for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, return the complete appliance and accessories, freight prepaid to:
US.: EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date must be included. *
Non-durable parts including, without limitation, those which normally require replacement are
specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or
damage due to faulty packaging or mishandling in transit. This warranty does not cover damage
or defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event
is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly str iving to impro ve our products, ther efore the
specifications contain ed her ein are subject to change wi thout noti c e.
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The
registration will enable us to contact you in the unlikely event of a product safety notification. By
returning this card you acknowledge to have read and understood the instructions for use, and
warnings set forth in the accompanying instructions. RETURN TO:
EURO-PRO Operating LLC, 94 MAIN MILL STREET, DOOR 16, PLATTSBURGH, NY 12901
____________________________________________________________________________
Model GC130HS
Appliance model
____________________________________________________________________________
Date purchased Name of store
____________________________________________________________________________
Owner’s name
____________________________________________________________________________
Address City State Zip Code
Printed in China
13
Troubleshooting
PROBLEM POSSIBLE REASON POSSIBLE SOLUTION
VACUUM WILL
NOT OPERATE
VACUUM WILL
NOT PICK UP OR
SUCTION POWER
IS WEAK
TURBO BRUSH
DOES NOT
ROTATE OR
ROTATES SLOWLY
DUST ESCAPING
FROM VACUUM
VACUUM HOSE OR
BRUSHES WILL
NOT PICK-UP
1. Power cord not firmly
plugged into outlet.
2. No power in wall outlet.
3. Needs servicing.
4. Thermostat has tripped.
1. Vacuum dust bag is
full.
2. Unit clogged.
3. Filter needs cleaning or
replacing.
1. Dust cup is full.
2. Rotating brush or
elbow is obstructed.
3. Belt is broken.
4. Hose obstructed.
5. Filters need cleaning.
1. Vacuum dust bag is
full.
2. Vacuum dust bag is not
installed correctly.
1. Hose clogged.
2. Vacuum dust bag is
full.
1. Plug unit in firmly.
2. Check fuse or breaker.
Replace fuse/reset breaker.
3. Call 1 (800) 798-7398.
4. Turn the unit off and unplug
from outlet. Allow unit to
cool down, then restart.
1. Replace vacuum dust bag.
2. Turn unit off and unplug
from wall outlet. Remove
vacuum bag filter and check
for object(s) in dust inlet and
remove.
3. Clean or replace filter.
1. Empty dust cup.
2. Clear obstruction(s).
3. Call 1 (800) 798-7398.
4. Clear obstruction(s).
5. Clean filters.
1. Replace vacuum dust bag.
2. Review vacuum dust bag
instructions.
1. Remove hose and/or
brushes. Remove
obstruction from hose
and/or brushes.
2. Replace vacuum dust bag.
To Order Replacement Filters and Bags
REPLACEMENT FILTERS AND BAGS
For Model: GC130HS
Item # XGC130H
(2 Pre-Motor Filters, 2 HEPA-Ty pe Filters, 6 Vacuum Dust Bags)
To order replacement filters and bags please call
EURO-PRO customer service:
1 (800) 798-7398
IMPORTANT SAFETY INSTRUCTIONS
When using your Garbage Can & Central Vac System, basic safety precautions
should always be observed, including the following:
• READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
• ALWAYS FOLLOW THESE SAFETY INSTRUCTIONS
• DO NOT LEAVE CLEANER UNATTENDED
• DO NOT USE APPLIANCE FOR OTHER THAN ITS INTENDED USE
• WARNING: FULLY ASSEMBLE CLEANER BEFORE OPERATING
1. Do not leave garbag e can when it
is plugged in. Unplug from outlet
when not in use and before
removing filters and dust bag.
2. To reduce the risk of electric shock
do not use outdoors or on wet
surfaces.
3. Do not allo w childr en to use as a
toy. Close attention is necessary
when used by or near children.
4. Use only as described in this
manual. Use only manufacturer’s
recommended attachments.
5. Do not use with damaged cord or
plug. Do not use vacuum cleaner if
it has been dropped, damaged, left
outdoors, or dropped into water.
Instead, return it to EURO-PRO
Operating LLC for inspection.
6. Do not pull or carry it by its cord.
Do not use the cord as a handle,
close a door on cord, or pull cord
around sharp edges or corners. Do
not run appliance over cord. Keep
cord away from heater surfaces.
7. Do not unplug by pulling on cord.
To unplug, grasp the plug, not the
cord.
8. Do not use the garbage can to pick
up large objects or objects that are
likely to damage the garbage can.
9. Keep hair, loose clothing, fingers,
feet and all parts of body away
from openings, rotating agitator
and other moving parts.
WARNING:
The power cord on this product contains lead, a chemical known to
the State of California to cause birth defects or other reproductive harm. Wash
hands after handling.
10. Do not pick up hot coals, cigarette
butts, matches or any hot,
smoking, or burning objects.
11. Do not pick up hard or sharp
objects such as glass, nails, etc.
12. Do not use without dust bag and/or
filter in place.
13. Turn off all controls before plugging or
unplugging vacuum cleaner into
electrical outlet.
14. Use extra care when cleaning on stairs.
15. Do not pick up flammable or
combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
16. Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
17. Do not use in an enclosed space filled
with vapors given off by oil based
paints, paint thinner, moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
18. Use only on dry, indoor surfaces.
19. Do not use for any purpose other than
described in this owner’s manual.
20. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and
anything else that may reduce air flow.
21. Store your appliance in a cool, dry
area.
22. Keep your work area well lit.
23. Do not immerse the vacuum into water
or liquids.
24. Keep end of hose, wands and other
opening, away from your face and
body.
25. To avoid damaging the carpet, keep
the vacuum cleaner head moving at all
times.
12
SAVE THESE INSTRUCTIONS
For Household Use Only
WARNING: To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug wil
the outlet, reverse the plug. If it still does not fit, contac t a qualified electrician to install
fully in
the proper outlet. Do not modify the plug in any way.
l fit in a polarized outlet only one way. If the plug is not fit
1 REV 06/06
Precautionary Measures
Bag and Filter Instructions
Important: If the suction opening in the unit or the hose becomes blocked, switch off
the unit and remove the blocking substance before you start the unit again.
1. Do not place the unit too close to
heaters.
2. Before inserting the power plug into
the wall outlet, make sure that your
hands are dry.
3. Do not vacuum an y liquids.
4. When pulling out the power plug
from the wall outlet. Pull the plug
not the power cord.
5. Do not dispose of or pick up
anything that is burning or smoking
such as cigarettes, matches or hot
ashes.
6. Do not use without garbage bag,
filters, and vacuum dust bag in
place.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THE POWER
CORD MUST BE DISCONNECTED BEFORE REMOVING
THE DUST BAG, THE PRE-MOTOR AND HEPA FILTER, OR
PERFORMING MAINTENANCE AND TROUBLE SHOOTING
CHECKS.
WARNING: NEVER OPERATE THE VACUUM WITHOUT THE
VACUUM BAG AND ALL THE FILTERS IN PLACE.
HOW TO CHANGE AND CLEAN
THE HEPA-TYPE FILTER
Note: The HEPA-Type filter is located
at the back of the unit. (Fig. 17)
Important Note: This is a HEPA-
Type filter, and will stop most of the
tiniest dust particles from re-entering
the air you breathe. Because of this
filtration performance, the filter will
quickly accumulate many fine dust
particles inside the white filter folds that
are difficult to see but which will
eventually block or reduce your suction
power if not cleaned properly. Clean
the filter after each use as described in
this section.
The HEPA-Type filter should be
cleaned after every use. To change
and clean the HEPA-Type filter,
perform the following:
1. Unplug unit.
2. Remove the HEPA-Type filter
cover. (Fig. 17)
3. Take out the HEPA-Type filter.
4. Vigorously “TapClean” the HEPAType filter on a hard surface to
remove any residual dust that
might still be on the HEPA-Type
filter.
5. You can wash the HEPA-Type filter
by running it under the tap allowing
the water to run on the dirty side at
least once a month or when suction
is decreased.
Important Note: We recommend
washing it once a month or when
suction is reduced. Always allow 24
hours for drying before replacing into
the vacuum. DO NOT USE A
WASHING MACHINE TO WASH THE
FILTER. DO NOT USE A HAIR
DRYER OR CLOTHES DRYER TO
DRY THE FILTER.
The HEPA-Type filter should however
be replaced every three (3) to six (6)
months to ensure peak performance of
your vacuum.
Warning: Always clean the HEPA-
Type filter before each use and during
prolonged usage or risk motor damage.
HEPA Filter
Cover
Fig. 17
2
11
Bag and Filter Instructions
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THE POWER
CORD MUST BE DISCONNECTED BEFORE REMOVING
THE DUST BAG, THE PRE-MOTOR AND HEPA FILTER, OR
PERFORMING MAINTENANCE AND TROUBLE SHOOTING
CHECKS.
WARNING: NEVER OPERATE THE VACUUM WITHOUT THE
VACUUM BAG AND ALL THE FILTERS IN PLACE
GETTING TO KNOW YOUR
GARBAGE CAN & CENTRAL VAC SYSTEM
FRONT VIEW OF BASE
HOW TO CHANGE AND CLEAN
THE PRE-MOTOR FILTER
Note: The pre-motor filter is located in
the base of the unit. (Fig. 15)
Pre-Motor
Filter
Fig. 15
To change and clean the pre-motor
filter, perform the following:
1. Unplug unit.
2. Lift off the outer metal enclosure
from the base of the unit.
3. Remove the vacuum bag cover,
and remove the vacuum bag in
order to gain access to the premotor filter.
4. Remove the pre-motor filter cover
by sliding it upwards. (Fig. 16) It
should slide off easily.
Pre-Motor
Filter Cover
Slide Pre-Motor
Filter Upwards
Fig. 16
5. Remove the pre-motor filter and
clean it by rinsing it under
lukewarm water.
DO NOT WASH THE FILTER IN
THE WASHING MACHINE.
Allow the pre-motor filter to air dry
for 24 hours. It may only be put
back in the unit when it is
thoroughly dried.
DO NOT USE A HAIR DRYER OR
CLOTHES DRYER TO DRY THE
FILTER.
6. Once the filter is put back into the
unit, replace the pre-motor cover
by aligning it with the grooves and
sliding it downwards until it is fully
in place.
1. Lid Release Button
2. Lid
3. Cover
4. Garbage Bin
5. Handle
6. Outer Metal Enclosure
7. Vacuum Bag Cover
8. Vacuum Bag Holder
9. Pre-Motor Filter Cover
(Filter not shown)
10. HEPA-Type Filter Cover
(Filter not shown)
11. Base
12. Dust Inlet Cover
13. Vacuum Bag Release
14. Extension Tube
(x2)
15. Crevice T ool
16. Dusting Brush
17. Small T urbo Brush
18. Flexible Hose
19. Floor Turbo Brush
20. Po wer Indicator Light
21. Vacuum Bag F ull Indicator Light
22. Suction Intake
23. Power Button
24. Vacuum Bag
(x4) (Not shown)
INNER VIEW OF BASE
10
Technical Specifications
Voltage: 120 V., 60 Hz.
Power: 12 A.
* Illustration may differ from actual product
3
Before Using Your
Garbage Can & Central Vac System
1. Read all instructions before using your Garbage Can & Central Vac System for
the first time.
2. Remove all packing materials and fully assemble unit as instructed on page 5
before operating.
DO NOT LEAVE UNIT UNATTENDED WHEN IN USE.
WARNING: FULLY ASSEMBLE UNIT BEFORE OPERATING.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THE POWER
CORD MUST BE DISCONNECTED BEFORE REMOVING
THE DUST BAG, THE PRE-MOTOR AND HEPA FILTER, OR
PERFORMING MAINTENANCE AND TROUBLESHOOTING
CHECKS.
Turbo Brush Instructions
3. Using your thumb and index finger,
simultaneously squeeze the locking
tabs on either side of the trap door
and lift off. (Fig. 13) Doing so will
remove the trap door and allow you
access to the turbine for cleaning
and maintenance purposes.
(Fig. 14)
Locking
Tabs
Fig. 13
4. There may be some dust, lint, hair,
etc on the turbine wheel. Remove
as much of this as possible.
5. You may also use the unit’s hose
with crevice tool attached and use
the vacuum to remove any
additional debris from the turbine.
6. Ensure that the turbine wheel
moves freely by rotating it with your
finger. If the turbine does not rotate,
call EURO-PRO Customer Service
for help at 1 (800) 798-7398.
7. Once clean, replace the trap door of
the turbo brush. Ensure that it clicks
into place.
WARNING: NEVER OPERATE THE VACUUM WITHOUT THE
VACUUM BAG AND ALL THE FILTERS IN PLACE
Using Your Garbage Can & Central Vac System
as a Traditional Garbage Can
The Garbage Can & Central Vac System can be used as a garbage can and vacuum,
or it can be used solely as a traditional garbage can. To use this multi-purpose unit as a
traditional garbage can, simply leave the unit unplugged from outlet (follow the power
cord storage instructions), and store the vacuum accessories for future use.
No filters are needed for use as a traditional garbage can, however the use of plastic
garbage bags are highly recommended for sanitary reasons. The garbage bin fits 8
gallon garbage bags (not included with unit).
Maintenance & Cleaning Instructions
The following instructions should be followed in order to keep the unit clean and
functioning:
• When garbage bag is full, remove cover and take out garbage bag.
• Should any garbage residue remain in the garbage bin, wipe clean using a damp
cloth, and then wipe dry using a soft, dry cloth. A mild cleaning product may be used
to remove persistent garbage residue.
• Before further use of garbage can, replace with a new garbage bag immediately.
• Wipe outer metal enclosure with a damp cloth. Should any garbage residue remain
on the outer metal enclosure, wipe clean using a damp cloth, and then wipe dry
using a soft, dry cloth. A mild cleaning product may be used to remove persistent
garbage residue.
Trap Door
Turbine
Fig. 14
4
9
Air Driven Turbo Brush Instructions
Motor Protective Thermostat
USING THE UNIT WITH AN
AIR DRIVEN TURBO BRUSH
Note: Your Air Driven Turbo Brush
may be used with either the extension
tubes or the flexible hose. The
efficiency of your Air Driven Turbo
brush depends on the bristle brush
rotating at high speed. Strong air
suction is needed to accomplish this. In
order to ensure that maximum air
suction is maintained, please read the
following instructions:
1. Change the vacuum bag when full.
2. Ensure that the rotating brush is
kept free of hair and string which
may accumulate and decrease
brush performance.
3. Keep Air Driven Turbo Brush
turbine free of dirt and foreign
matter. (See illustration below for
cleaning instructions.)
How To Clean the
Small Turbo Brush
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the
hose or extension tube.
2. Slide locking latch forward then tilt
the top housing of the brush
upwards. The top housing is hinged
and will tilt up approximately 45°
only. (Fig. 11)
3. There may be some dust, lint, hair,
etc on the turbine wheel. Remove
as much of this as possible.
4. You may also use the unit’s hose
with crevice tool attached and use
the vacuum to remove any
additional debris from the turbine.
5. Ensure that the turbine wheel
moves freely by rotating it with your
finger. If the turbine does not rotate,
call EURO-PRO Customer Service
for help at 1 (800) 798-7398.
6. Once clean, close the top cover of
the turbo brush and slide the locking
latch toward the rear of the brush to
lock.
How To Clean the
Floor Turbo Brush
From time to time, the turbine of your
turbo brush will require cleaning. To do
this:
1. Remove the turbo brush from the
hose or extension tube.
2. Flip the turbo brush over so that the
bottom of it is facing upwards.
(Fig. 12)
MOTOR THERMOSTAT
Important: This unit is equipped with
a motor protective thermostat. If for
some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the power button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem (i.e. clogged hose, filter,
or full vacuum bag).
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the power button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1(800) 798-7398.
Power Cord Storage
When the unit is not in use, it is important to follow proper power cord storage
instructions:
1. Pull out the power cord from the wall outlet.
2. Loosely wind the power cord and leave at the back of the unit, giving it enough
space so that it does not become damaged. DO NOT LET THE POWER CORD
LIE ON OR NEAR WATER OR ANY OTHER KIND OF LIQUID.
3. Always check if the power cord is damaged or if the plug is wet before use.
Assembling Instructions
1. Assemble the plastic garbage bag
to the garbage bin. (Fig. 1)
3. Put the cover on the garbage bin,
and put the garbage bin and outer
metal enclosure on the base of the
unit. (Fig. 3 & Fig. 4)
Locking Latch
Turbine
Tilt
Upwards
Fig. 12
Fig. 1
2. Put the garbage bin in outer metal
enclosure. (Fig. 2)
Fig. 2
8
5
Fig. 3
Fig. 4
Operating Instructions
Bag and Filter Instructions
DO NOT LEAVE UNIT UNATTENDED WHEN IN USE.
WARNING: FULLY ASSEMBLE UNIT BEFORE OPERATING.
WARNING: NEVER OPERATE THE VACUUM WITHOUT THE
VACUUM BAG AND ALL THE FILTERS IN PLACE
HOW TO OPERATE
Using the Dust Inlet
1. Ensure vacuum bag and filters are
in place before using.
2. Plug unit into outlet. Check that the
power cord is not damaged or wet
before use.
3. Push the power button to turn on the
unit. When the unit has been turned
on, the power indicator light will go
on. (Fig. 5) Once the unit is on,
sweep the dirt/dust to the dust inlet.
The dust inlet will then suck up the
dirt/dust. To turn the unit off, push
the power button a second time.
Power
Indicator
Light
Power
Button
Fig. 5
Using the Central Vac System
1. Ensure vacuum bag and filters are
in place before using.
2. Remove dust inlet cover and insert
hose into suction intake. (Fig. 6)
Dust
Inlet
Cover
Fig. 6
3. Attach desired accessory to hose.
Attach extension tubes as
necessary.
• Dusting Brush
Use on furniture, drapes, and
walls.
• Crevice Tool
Use on furniture and between
cushions.
• Small Turbo Brush
Use on furniture.
• Floor Turbo Brush
Use on floors or carpets.
4. Once having attached the desired
accessory, you may push the power
button to turn the unit on and start
the suction. To stop suction push
the power button once more.
6
Suction
Intake
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THE POWER
CORD MUST BE DISCONNECTED BEFORE REMOVING
THE DUST BAG, THE PRE-MOTOR AND HEPA FILTER, OR
PERFORMING MAINTENANCE AND TROUBLE SHOOTING
CHECKS.
WARNING: NEVER OPERATE THE VACUUM WITHOUT THE
VACUUM BAG AND ALL THE FILTERS IN PLACE.
VACUUM BAG
How to Remove and Replace the
Vacuum Bag
Note: The vacuum bag is located in
the base of the unit.
The vacuum bag full indicator light
will go on to indicate that the bag is full
and needs to be replaced. To replace
the bag perform the following steps:
1. Unplug unit.
2. Lift off the outer metal enclosure
from the base of the unit.
3. Remove the vacuum bag cover.
(Fig. 7)
Fig. 7
4. Press on the vacuum bag release,
in order to release the bag and
remove it. (Fig. 8)
Vacuum Bag
Release Button
Fig. 8
5. Remove the vacuum bag from the
vacuum bag holder. (Fig. 9) The
vacuum bag should slide out easily
from the vacuum bag holder. Put
the dirt and dust filled vacuum bag
in the garbage bin.
Slide
vacuum
bag holder
upwards
Fig. 9
6. Take a new vacuum bag and
attach it to the vacuum bag holder
by sliding the vacuum bag’s
cardboard front into the grooves of
the vacuum bag holder. It should
slide in easily. (Fig. 10) DO NOT
REUSE THE VACUUM BAG.
Slide
vacuum
bag holder
upwards
Fig. 10
7. Press on the vacuum bag release,
and align the hole on the vacuum
bag holder with the suction intake
hole under the vacuum bag
release button. Once aligned and
in place, stop pressing the vacuum
bag release in order for it to remain
in place.
7
Vacuum
Bag
Holder
Vacuum
Bag
Holder
Loading...