STEAM GENERATOR
OWNER’S MANUAL
Model G6118H
120V., 60 Hz., 1500 Watts
IRON
For information or assistance:
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: (800) 798-7398
IMPORTANT SAFETY INSTRUCTIONS
When using your Steam Generator Iron, basic safety precautions should always be followed.
Read carefully the following instructions as they provide important information concerning how to
install, use and care for this appliance.
1. Use steam generator iron only for its
intended use.
2. Use ironing system only for its intended
use.
3. To protect against a risk of electric shock,
do not immerse the iron or any part of the
ironing system in water or any other
liquids.
4. The ironing system (iron and steam
generator) should always be turned OFF
before plugging into or unplugging from
wall outlet. Never pull power cord to
disconnect from outlet; instead, grasp
plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces.
Let the ironing system cool completely
before putting away or opening water
tank (removing safety cap). Wrap cord
loosely around the ironing system when
storing.
6. Always disconnect ironing system from
electrical outlet when filling with water or
emptying and when not in use. Always
turn the safety cap slowly when opening
the water tank.
7. Always make sure that there is no
steam in the steam generator (water
tank) before opening the safety cap.
Follow instructions to release all
remaining steam though the iron by
pressing the steam release button.
Unplug the unit and allow to cool before
starting to open safety cap. Always turn
the cap slowly when opening the water
tank to allow any remaining steam to
escape gradually.
8. Do not operate the ironing system with a
damaged cord, plug or if the iron or any
other part of the system has been
dropped or damaged. To avoid risk of
electric shock, do not disassemble or
attempt to repair the ironing system.
Return the unit to EURO-PRO Operating
LLC (see warranty) for examination,
repair or replacement. Incorrect
reassembly or repair can cause a risk of
electrical shock or injury to persons when
the ironing system is used.
9. Close supervision is necessary for any
appliance being used by or near children.
Do not leave ironing system unattended
while connected or while on an ironing
board. Always position the iron flat on the
silicone rubber posts.
10. Burns can occur from touching hot metal
parts, hot water or steam. Use caution
when turning the system upside down, as
there may be hot water in the unit. Never
direct steam at any person, especially
when using the iron in the vertical
position. The steam is very hot and can
cause burns.
11. The hot iron base (soleplate) must always
rest on the non combustible silicone
rubber posts on top of the steam
generator.
12. Do not operate in the presence of
explosive and/or flammable fumes.
13. Never fill the boiler with corrosive products
like vinegar or limestone removers.
14. Never move the steam generator during
use and never fill it under running water.
15. CAUTION: Never use scouring pads,
abrasive or chemical cleaners, or
solvents to clean the exterior or
soleplate of your iron. Doing so will
scratch and/or damage the surface.
16. Use regular tap water or distilled/purified
water if the tap water in your area is
very hard.
17. This appliance is intended only for
household use. Follow all user
instructions in this manual.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not
operate another high-wattage appliance
on the same circuit simultaneously with
the steam generator iron.
2. If an extension is absolutely necessary, a
15-ampere rated cord with a polarized
plug should be used. Cords rated for
less amperage may overheat. Care
should be taken to arrange so that it
cannot be pulled on or tripped over.
3. Do not leave iron unattended when the
system is connected to a power
supply/electrical outlet.
POLARIZED PLUG
WARNING: To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
Rev. 09/03C
G6118H
1 YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, return the complete appliance and accessories, freight prepaid to
EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
If the appliance is found by EURO-PRO Operating LLC to be defective in material or
workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of
purchase date and $ 14.95 to cover the cost of return shipping and handling must be included. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement
of the unit at our option. This warranty does not cover normal wear of parts and does not apply to
any unit that has been tampered with or used for commercial purposes. This limited warranty does
not cover damage caused by misuse, abuse, negligent handling or damage due to faulty
packaging or mishandling in transit. This warranty does not cover damage or defects caused by
or resulting from damages from shipping or repairs, service or alterations to the product or any of
its parts, which have been performed by a repair person not authorized by EURO-PRO Operating
LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential
damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address
and phone number with a note giving purchase information, model number and what you
believe is the problem with item. We recommend you insure the package (as damage in
shipping is not covered by your warranty). Mark the outside of your package “ATTENTION
CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
PRODUCT REGISTRATION CARD
Please complete and return within ten (10) days of purchase. The registration will enable us to
contact you in the event a product defect is discovered. By returning this card you acknowledge
to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
RETURN TO: EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
PURCHASER: ……………………………………………………………………………………………
ADDRESS: ……………………………………………………………………………………………….
DATE OF PURCHASE: …………………….. ………… MODEL: ……. ……………. .…………….
NAME AND ADDRESS OF STORE: …………………………………………………………………..
Printed in China
101
G6118H
TROUBLSHOOTING
Do not operate the steam generator with a damaged cord, plug or if the iron or any
other part of the system has been dropped or damaged. To avoid the risk of electric
shock, do not disassemble or attempt to repair the ironing system. Return the
appliance to EURO-PRO Operating LLC (see Warranty) for examination and repair.
Incorrect re-assembly or repair can cause a risk of electric shock or injury to persons
when the ironing system is used.
PROBLEM
No Steam Is
Released
Through The
Iron
The Soleplate
Remains Cold
Drops Of Water
Leak From The
Iron Soleplate
Dirty Or Yellow
Steam Is
Coming Out Of
The Iron
Steam Leaking
From The Boiler
Filler Cap
POSSIBLE CAUSES SOLUTIONS
1. Press the On/Off button to
1. On/Off button is not in the
“ON” position.
2. Steam generator has no more
water.
3. Unit is not plugged in.
4. Steam is not visible because
the temperature of the
soleplate is at maximum and
room temperature is high.
5. Generator is not fully heated.
1. Temperature is set at
“Minimum”.
1. Soleplate temperature is too
low to iron with steam.
2. Generator is not fully heated.
1. Residue is water tank.
2. Not using demineralized/
distilled water.
1. Gasket is broken because
boiler filler cap was closed too
tightly or cap was opened
while tank was full of steam
and gasket broke.
the “ON” position.
2. Fill with water as per
instructions.
3. Make sure that the On/Off
button is in the “OFF”
position and plug the unit
into an electrical outlet.
4/5. The heating time for the
generator is approximately
11-13 minutes. Watch for
the steam ready light to go
off indicating that steam is
ready.
1. Turn the temperature
control dial to the desired
setting.
1. Turn the temperature
control dial to the marks
between 2 and 3 dots.
2. Wait for generator to be
fully heated.
1. Clean steam generator as
per instructions.
2. Use demineralized/ distilled
water after cleaning the
tank.
1. Order new boiler filler cap
from customer service at 1
(800) 798-7398.
ADDITIONAL IMPORTANT SAFEGUARDS
Read all instructions before using the EURO-PRO Operating LLC Steam Generator
Iron and follow all the instructions and safeguards carefully.
CAUTION! NEVER open the
boiler filling cap before ALL
the remaining steam has been
released from the steam
generator and the steam
generator has cooled. To
release the steam, press the
On/Off button to the “Off”
position and push the steam
button on the iron until no
more steam comes out of the
iron. Then open the boiler filler
cap slowly.
A WORD ON WATER
For best results we recommend using
100% demineralized/distilled water.
You can use regular tap water in your
steam generator, but should the water in
your area be hard water we strongly
recommend the use of 100%
demineralized/distilled water. This will
prolong the life of your generator and
reduce the frequency of required generator
cleaning, as well as the possibility of
staining due to accumulated impurities.
DO NOT USE WATER PROCESSED
THROUGH A HOME WATER
SOFTENING SYSTEM OR BOTTLED
MINERAL WATER.
DO NOT OVERFILL THE STEAM
GENERATOR
When empty, the steam generator can be
filled with 26 U.S. fl. oz. of demineralized/
distilled water. Do NOT
the water tank can cause water drops to
come out of the steam holes. See filling
instructions on page 5.
overfill. Overfilling
DO NOT OVER TIGHTEN THE
BOILER FILLER CAP
To close the boiler filler cap, turn
clockwise until the point where you feel
friction – do NOT close too tightly. The
boiler filler cap has a gasket which can
be flattened and damaged if the cap is
closed too tightly. If the gasket is
damaged, steam may escape while the
steam generator is being used. If the
boiler filler cap is damaged and steam
is leaking, call customer service to
purchase a replacement boiler filler
cap.
NEVER LEAVE THE HOT IRON
RESTING ON THE IRON REST
FOR LONG PERIODS OF TIME
The lifespan of your steam generator
will be reduced if the iron is left idle at
high temperatures for extended
periods of time. If the iron is not in use,
reduce the temperature to the lowest
temperature setting on the temperature
control thermostat, turn the steam
generator “Off” and remove the power
cord from the electrical power outlet.
WARRANTED FOR REGULAR
HOUSEHOLD USE
This Steam Generator Ironing system
is intended for and warranted only for
normal household use. The iron and/or
steam generator should not be used
for more than fifteen (15) hours per
week in approximately three (3) hour
intervals.
9 2
OPERATING INSTRUCTIONS
Even if you have used a steam generator iron before, please read all instructions
and safeguards in the Use and Care Instruction Book. In addition, please note the
following user tips:
USING STEAM
PLEASE NOTE: Steam performance improves after the first 6-8 hours of usage.
The steam power increases and initial condensation at maximum
temperature is reduced.
1. Make sure the temperature setting of the iron is within the steam range on the
temperature selector.
2. Turn power on for iron and steam generator. Before starting to use steam,
make sure the Steam Ready Light is “ON”
NOTE: Trying to use steam before the Steam Ready Light is “ON” can cause water
drops in the steam coming out of the iron.
CLEARING THE INITIAL CONDENSATION:
3. Clear the initial condensation by pressing the Steam Button up to 3 seconds.
Repeat if necessary.
IMPORTANT NOTE:
4. While using the ironing system, if steam has not been released for more than
approximately 5 minutes, the hose has cooled and any steam remaining in the
hose from the last use might condense. Clear this condensation by pressing
Steam Button before proceeding to use the iron.
, indicating that steam is available.
CLEANING & MAINTENANCE
CAUTION! NEVER open the
boiler filler cap before ALL the
remaining steam has been
released from the steam
generator and the steam
generator has cooled. To
release the steam, press the
On/Off button to the “Off”
position and push the steam
button on the iron until no
more steam comes out of the
iron. Then open the boiler filler
cap slowly.
1. We strongly recommend the use of
demineralized/distilled water to
ensure optimum performance and
maximize the life of your steam
generator. If you are using
demineralized/distilled water, the
steam generator should be cleaned
once every six (6) to twelve (12)
months. If you use regular tap water,
the steam generator should be
cleaned once a month.
2. Make sure that all the steam has
been released from the steam
generator before doing any cleaning
or maintenance on the appliance.
Follow instructions on page 7 for
releasing the steam.
3. Remove the power cord from the
electrical outlet and let the unit cool
down for at least 4 hours after it has
been used before starting to clean
the steam generator.
4. NEVER immerse the iron or the
steam generator in water or any
other liquid.
CLEANING THE STEAM
GENERATOR BASE
1. Make sure that there is no steam
remaining in the steam generator.
2. Make sure that the steam generator is
completely cold.
3. Remove the boiler filler cap by slowly
turning counter clockwise to allow any
remaining steam to escape.
4. Fill water tank with a solution of 20%
vinegar and 80% water (5 oz vinegar
and 21 oz of water) and let sit
overnight (8-12 hours).
5. Replace the boiler filler cap and
shake.
6. Remove the boiler filler cap and
empty the tank. Rinse with water two
to three times by filling, shaking and
emptying again.
6. Wipe the outside of the steam
generator base with a damp cloth.
CLEANING THE STEAM
GENERATOR IRON
1. Clean the steam generator iron
ONLY when cold.
2. Do NOT use scouring pads,
abrasives or harsh cleansers.
3. Use a commercially sold soleplate
cleanser following the manufacturers
label instructions.
4. Use a soft damp cloth to wipe the
outer shell of the iron.
5. Dry soleplate and iron thoroughly
after cleaning.
STORING YOUR STEAM
GENERATOR IRON
1. Ensure that the seam generator is
depressurized by opening the steam
button on the iron until no further
steam is escaping.
2. Always unplug the power cord from
the electrical outlet when not in use.
3. Always store in a dry place away
from the reach of children.
4. Always drain the water tank before
storing.
5. Always let your steam generator cool
completely before storing.
6. Do not let power cord and steam
hose to touch hot surfaces.
7. Wrap the power cord and steam
hose around the appliance loosely.
3
8
OPERATING INSTRUCTIONS GETTING TO KNOW YOUR STEAM GENERATOR
REFILLING THE STEAM
GENERATOR
WARNING! Never direct the
steam from the iron at yourself
or another person. Special care
must be taken when the iron is
used in a vertical position. The
steam is very hot and can
cause burns.
1. Press the steam generator On/Off
button to the “OFF” position.
2. Release all the remaining steam in
the steam generator by pressing the
steam button until no more steam is
coming out from the iron.
3. Unplug the appliance from the wall
outlet. Allow it to cool for a minimum
of 5 minutes.
4. To unscrew the boiler filler cap, push
down and turn counter clockwise
slowly. If any steam continues to
escape, STOP
steam through the iron as in the
steps above.
5. Using a measuring cup, fill the water
tank with 26 US fl. oz.
6. Replace the boiler filler cap turning
clockwise until you get friction. DO
NOT OVERTIGHTEN OR GASKET
WILL BE FLATTENED.
and release the
PRESSING TIPS
Dry Steam vs Humid Steam
In a steam generator iron the steam
is produced in the generator and not
in the iron as with regular household
irons. The temperature of the iron
determines the type of steam – dry
or humid. At high temperatures, the
iron delivers very dry steam. Lower
temperature settings offer humid
steam.
For best pressing results, you have
the flexibility to select the type of
steam and not only the iron
temperature. A balance should be
maintained between the humidity
(low iron temperature) required to
loosen fibers and the need for heat
(higher iron temperatures) to
flatten/shape and dry the fibers.
PRESSING TIPS (cont.)
Instructions for specific iron
temperature settings should be
treated as guidelines only. We
recommend that you test each type
of fabric on an inside seam before
proceeding to iron the garment. The
steam generator iron can produce
humid steam at relatively low
temperature settings where regular
household irons would release
water. At the same time, the very dry
steam produced at the high iron
temperature setting “•••” can be used
on some fabrics where normally the
use of steam is prohibited.
PRESSING DIFFICULT FIBERS
(i.e. 100% COTTON)
Your Steam Generator Iron features
steam holes placed in the front of the
iron soleplate. Correct ironing
procedure involves steaming the
fabric with the front end of the iron
followed by pressing and drying with
heat from the rear of the iron. For
best results, garments should be dry
after pressing to avoid re-wrinkling
due to lingering dampness.
Therefore, we recommend that you
use the steam as required, but not
continually.
While your Steam Generator Iron
offers high quality type steam, some
fabrics may require additional
moisture for best results. You may
want to press cotton shirts while still
damp or spray with water prior to
ironing.
1. Boiler Filler Cap
2. Steam Ready Light (green)
3. On/Off Button (red)
4. Steam Generator Base
5. Iron Rest Plate
6. Power Cord
Technical Specifications
Voltage: 120V., 60Hz.
Power: 1500 Watts
Water Capacity: 26 US fl. Oz.
Working Pressure: 2.9 bar
7. Steam Hose
8. Steam Button
9. Temperature Ready Light
10. Temperature Control Dial
11. Stainless Steel Soleplate
7
4
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
This appliance is for HOUSEHOLD USE
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
BEFORE FIRST USE
Remove any labels, stickers or tags
which may be attached to the body or
the soleplate of the iron before using
the steam generator.
WARNING! Never leave the
unit unattended while plugged
in. Always turn the steam
generator “OFF” and remove
the power cord from the
electrical outlet.
WARNING! The steam
generator must always be
turned “OFF” and
disconnected from the
electrical outlet before any
cleaning or maintenance;
before filling and emptying the
water tank.
FILLING STEAM
GENERATOR WATER TANK
1. Place steam generator unit on
a solid flat surface.
2. Unscrew the boiler filler cap.
3. When filling the steam
generator water tank, always
use a measuring cup to fill
your unit. NEVER fill the
appliance under a tap. Fill the
water tank with 26 US. fl. oz.
of tap water if the water in
your area is not hard water. If
it is, then we strongly
recommend using 100%
demineralized/distilled water.
Be careful not to over fill the
water tank. Adding too much
water will cause overfilling
and will result in water drops
on the steam.
4. When finished filling, replace
the boiler filling cap and screw
on tightly.
5. Plug the power cord into an
electrical outlet.
6. Press the On/Off button on the
stream generator to the “ON”
position.
7. Turn the temperature control dial on
the iron to the desired temperature
setting.
Temperature
Control
Dial
USING THE IRON WITH STEAM
1. Place the steam generator on a flat
stable surface.
2. Fill the steam generator with water.
3. Plug the power cord into an electrical
outlet.
4. Press the On/Off button to the “ON”
position. The steam ready light will
light up when the steam is ready.
It will take approximately 11-13
minutes to heat up a full tank of
water. The steam ready light will
go on and off while the steam
generator is in use.
5. Turn the temperature control dial to
the desired temperature setting
designated for use with steam, i.e.
between the two “••” and the three
“•••” dots on the temperature control
dial. The temperature ready light will
light up. The iron will have reached
the desired temperature setting
when the temperature ready light will
go off.
6. Press the steam button on the
handle of the iron to release the
steam.
Note: Trying to use steam before the
steam ready light has come on can
cause water drops to come out of
the iron instead of steam.
WARNING! Never direct the
steam from the iron at yourself
or another person. Special care
must be taken when the iron is
used in a vertical position. The
steam is very hot and can
cause burns.
DRY IRONING
1. Place the steam generator on a flat
stable surface.
2. Plug the power cord into an
electrical outlet and press the On/Off
button to the “On” position.
3. Set the temperature control dial
according to the garment label or
use the temperature guide below.
4. The temperature ready light will go
“OFF” when the desired temperature
has been reached.
5. You can iron at any temperature
setting without steam.
TEMPERATURE SETTINGS
• Always read the garment labels and
follow the manufacturer’s directions
when pressing a garment.
• For maximum efficiency, iron
garments requiring lowest
temperature setting first as the iron
heats up faster than it cools down.
• If there are no instructions included
with the garment, we suggest that
you follow the temperature guide on
page 6 as a guide (except when any
fabric has an applied finish, gloss,
etc. where lower temperatures might
be required.
• Always iron fabric blends, (fabrics
made of two or more types of fibers)
using the heat setting appropriate for
the fabric requiring the lowest
temperature setting.
NOTE: For best results, make sure that
the steam generator is filled to the
maximum level before every use.
IRONING TEMPERATURE GUIDE
Check garment labels for instructions i.e. do not iron chlorofiber
SUGGESTED
TEMPERATURE RANGEFABRICS
AMOUNT OF
STEAM
SYNTHETIC:
Acetates, Acrylics
Cresian, Metalics
Sheer Synthetic
Polyester, Dacron
Fortrel,
Perma Press, Nylon
Silk
Linen
MAX
Dry Ironing
(without steam)
Pure silk sometimes
requires steam
Humid SteamWool
Normal SteamCotton
Super Dry Steam
5
6
Loading...