Esotec Trendy Operating Manual
GB
hese instructions relate ONLY to this product and contain
T
important information for using the product for the first time.
Please keep these instructions for later reference and should
always accompany the product in the event of transference
o a new user.
t
hese instructions relate ONLY to this product and contain
T
important information for using the product for the first time.
lease keep these instructions for later reference and should
P
always accompany the product in the event of transference
o a new user.
t
Using Instructions “Trendy”
1. Introduction
Dear Costumer,
hank you for purchasing the solar light. With this solar light you
T
purchased a product manufactured according to the current state
f technology.
o
This product fulfils all requirements of the valid European
and national regulations. The conformity was proved. The
relevant declarations and documentation are deposited with
the manufacturer.
To maintain this state and guarantee a safe operation, you as the
user will have to follow this operating manual!
2. Safety Instructions
- In case of damages caused by not
following this operating manual, the
!
nal damages caused by inappropriate handling or not following the safety instructions.
- In these cases any guarantee rights will expire.
Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial
trade cooperative association for electric plants and working
material are to be considered in industrial environments.
warranty rights will expire! We exclude
liability for any consequential damages!
- We exclude liability for property or perso-
. Installation
4
1. Remove the parts cautiously from the packaging.
. Carefully screw the ball from the base part in a
2
counterclockwise direction (Figure 1) and carefully remove
the ball.
3. To prevent its theft, you can screw the ball on the floor; refer
to item 5. “Installation of the housing” in this instructions for
use.
4. Insert the plug of the battery unit into the socket on the board
(Figure 2).
Caution: After the plug was inserted, the LEDs will illuminate.
Do not directly look into the light to prevent ocular injuries.
ote:The plug can be inserted only in one orientation to prevent
N
wrong polarity. Never use excessive force when plugging in.
5. Now put the ball carefully on the base and fix it again by tur-
ing it clockwise. For this purpose, place the base on a table
n
with the solar battery directing to the front (Figure 3) and put
the ball on the stainless steel base while the notch in the
bayonet lock directs to the rear (Figure 4), then screw the
ball tightly to the base.
6. The solar light is now ready for operation and is charged by
the integrated solar module. Place the ball on a sunny place
with the solar module directing to the front.
Note: The duration of the illumination period strongly depends
on intensity and duration of the duration of sunshine during the
day. Therefore, it is normally shorter in wintertime. If the lamp
does not shine on the first evening, you should wait for another
sunny day.
1.
2.
Notch in the
bayonet lock
Ball
3. Intended use
The solar light is designed for interior and exterior use. Its light
changes between 7 colors; however
set it required.
The integrated battery is charged via the solar cell integrated
into the stainless steel base or the included plug-in power supply
(only for interior use).
During solar operation, the light automatically switches on at
dawn and off at daybreak. The light sensor is the solar cell.
The light is produced by 4 highly efficient LEDs. Their power
consumption is low, and their luminosity is high; their average
lifetime exceeds 100,000 hours.
Note: After prolonged period of insufficient sunshine, radiationinduced battery recharge may be low.
However, the solar light is not defective. After a couple of
sunny days, it will work again as before or charge the battery with the power supply.
It is recommended to replace the battery every 2 years.
, also a fixed color can be
3.
4.
- Optional operation with the integrated power supply.
1. Insert the plug of the mains power supply into the socket at
the bottom of the circuit board (Figure 5) and plug the power
supply into the mains. The battery is now charged via the
power supply.
2. Now put the ball carefully on the base and fix it again by tur-
ning it clockwise. The solar light is now ready for operation.
Caution: The power supply is
only suitable for interior operation!
5.
. Installation of the housing
5
1. Remove the lid of the stainless steel housing by holding its
top with the thumb and releasing it from the bottom with the
ingers (Figure 6).
f
3. Now retract the top from the bottom by lifting it up (Figure 7).
. The bottom of the housing has boreholes to fix the light. Use
2
the provided screws and plugs (Figure 8).
. Re-insert the top containing the solar module to the bottom
3
and carefully click the opposite side into place (Figures 7 and
).
9
12.
Press
Press
6. 7.
8.
6. Fixation of the light color
The light color can be permanently fixed by a switch on the
board (Figure 10). For this purpose, set the switch into the
“STOP” position within 5
seconds after the intended light
color illuminates. The light color
is fixed now. You can return to
the color change mode by simply switching the switch back.
7. Setting color duration
The duration of individual colors
in the color change mode can
be set to two positions with a
jumper (Figure 1
board. When the jumper is put
on, colors will change approximately every 15 seconds.
ithout jumper, colors will
W
change after approximately 60
seconds.
1) on the
9.
Color
Fix
11.
Press
Press
10.
Color
change
9. Troubleshooting
Lamp does not switch
on in the dark
Lamp does not switch
n in the dark or only
o
or a short period of
f
time.
- An external light source (e.g. a street lamp) simulates
daylight and prevents switching on of the light. Transfer
he module to a darker place
t
- Check all connectors for proper connection
Battery low or defective. Replace the battery every 2
-
ears or earlier.
y
10. Specifications
Operating voltage: 3.6 V
Battery: 1 x NiMh 3.6 V/1300 mAh
Illumination: 4 high-performance LEDs
Solar module: ASI Technik, 1 Watt, RWE Schott Solar
Length of illumination period: up to 15 hours with fully charged batteries
Battery take-back
- Batteries must not be discarded into domestic waste.
- The consumer is legally required to return batteries after use, e.g. to
public collecting centers or to battery distributors.
- Contaminant-containing batteries are labeled with the
sign “crossed-out trashcan“ and one of the chemical symbols Cd (= battery contains cadmium), Hg (= battery contains mercury), Pb (= battery contains lead).
Used batteries should be disposed environmentally
friendly and should not be discarded into domestic waste.
Your dealer is legally required to take back old batteries.
Manufacturer/ Importer:
esotec GmbH, Etzenrichterstr. 14, D-92729 Weiherhammer
el.-Nr: 0049 (0)9605-92206-28
T
Fax.-Nr: 0049 (0)9605-92206-10
e-mail:info@esotec.de
.esotec.de www
www
Copyright esotec GmbH
.sunnytrend.de
NiMh
8. Battery replacement
1. Remove the ball from the bottom by turning it counterclokkwise (Figure 1).
2. Plug off the plug of the battery unit from the board (Figure
12).
3. Press the two tabs at the battery compartment (Figure 12)
and open the battery compartment.
3. Replace the battery with a freshly loaded identical battery.
4. Now close the light in the reverse order.
Note: Used batteries should be disposed environmentally friend
our dealer
ly and should not be discarded into domestic waste.
is legally required to take back old batteries.
Y
-
Loading...