Esotec Sunny Operating Manual

Usage instructions

GB

Solarlight “Sunny”

These instructions relate ONLY to this product and contain important
information for using the product for the first time. Please keep these
instructions for later reference and should always accompany the
product in the event of transference to a new user.

. Introduction

1

Dear Costumer,
Thank you for purchasing the solar light.
With this solar light you purchased a product manufactured according to
the current state of technology.

This product fulfils all requirements of the valid European and natio-

al regulations. The conformity was proved. The relevant declarati-

n
ons and documentation are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will
have to follow this operating manual!

2. Safety Instructions

5. Exchange of Accumulators

witch

s

- In case of damages caused by not following this
operating manual, the warranty rights will expire!
We exclude liability for any consequential damages!

- We exclude liability for property or personal

!

Due to safety and admission reasons (CE) it is not allowed to arbitrarily
reconstruct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade
cooperative association for electric plants and working material are to be
considered in industrial environments

damages caused by inappropriate handling or not
following the safety instructions.

- In these cases any guarantee rights will expire.

3. Usage in Accordance with Requirements

The solar light is constructed for the outdoor usage and operation. The
integrated accumulators are charged by the solar cell in the upper part of
the light. At darkness, the light is automatically switched on and is swit­ched out at sunrise. As light source, 3 very strong light emitting diodes
(LED) are installed. These LEDs guarantee a strong luminosity with only
low power consumption.

-- However, please note that the duration of illumination may decrea­se due to a lack of sunshine as well as in the winter months--

In case of longer periods without sunshine (insolation) the accumulator is
charged only insufficiently and is thus not able to guarantee a permanent
readiness for operation. However, this does not indicate that the solar
light is defect. Please wait for the next sunny days and the light will again
be working accordingly

1. Hold the upper part and screw off the lower part of the lamp head
clockwise and take apart the parts.

2. Unscrew the reflector also clockwise and remove it.

3. Open the two battery compartments by pressing the lock.

4. Take the used accumulators out of the battery compartment and insert
two new accumulators, according to polarity, into the battery compart­ment. It is recommended to charge the new accumulators in a battery
charger before inserting them.

5. Re-assemble the lamp in reverse order.

Note: Used batteries or accumulators must be disposed of in a non-pol­luting way and do not belong into the domestic waste. Your dealer is
legally obliged to take back and recycle old accumulators.

6. Malfunctions

-Lamp is not automatically switched on at darkness

- An outside light source (e.g. streetlight) simulates daylight and prevents the lamp

from switching on. Place the lamp at a darker location.

- Lamp is not switched on at darkness or only for a short period of time.

- Is the lamp connected?

- Accumulator weak or defective. Exchange of the accumulators.

4. Initiation

1. Please carefully take all parts out of the package.

2. Please carefully connect the earth rod with the bar and insert it into the
ground.
Note: Please do not use force.

3. Adjust the switch below the lamp shade to the position “ON” and care­fully insert the upper part of the lamp onto the receiver module on the

.

bar

The solar light is now activated.

In case of wall installation:

horizontally fix the subbase to the wall with the enclosed screws.
screw on the carrier and reposition the lamp on top.

Note: In order to avoid scratching the wall carrier, do not use sharp­edged tools when tightening the nuts.

Note: The duration of illumination is strongly dependent on the intensity
and duration of sunshine during the day. During the winter months the
duration of illumination will generally be shorter. If the lamp should not
irradiate on the first evening, please wait for a sunny day

Unscrew the nuts at the wall carrier and

Then

.

7. Technical Data

Operation voltage: 2.4 V
Set of accumulators: 2 x NiMh 1.2 V/900 mAh
Light emitting diode:
Solar module: crystal silicon
Duration of illumination:

3 white light emitting diodes (LEDs)

max. 12 hours in case of fully charged set
of accumulators

Battery Recycling:

- Used batteries or accumulators must be disposed in
the domestic waste.

- The consumer is legally obliged to bring back old
accumulators upon usage, e.g. to public waste col
lecting locations or to the place (shops, etc.) where
those batteries are sold.

- Batteries that contain harmful substances are mar­ked with the “strike through dustbin” and one of the
chemical symbols Cd (= battery contains cadmium), Hg (= battery
contains hydrargyrum), Pb (= battery contains lead).

Hersteller/Importeur:

esotec GmbH, Etzenrichterstr. 14, D-92729 Weiherhammer
Tel.-Nr: 09605-92206-28, Fax.-Nr: 09605-92206-10,
e-mail:[e-mail], www.sunnytrend.de

Hersteller Art.-Nr: 102094

Copyright, Änderungen vorbehalten!

-

NiMh