Esotec Solar Lightballs Using Instructions

Using Instructions

GB

Solar Lightballs

These instructions relate ONLY to this product and contain important
information for using the product for the first time. Please keep these
instructions for later reference and should always accompany the
product in the event of transference to a new user.

1. Introduction

Dear Costumer,
Thank you for purchasing the solar light. With this solar light you purcha­sed a product manufactured according to the current state of technology.

This product fulfils all requirements of the valid European and natio­nal regulations. The conformity was proved. The relevant declarati­ons and documentation are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will
have to follow this operating manual!

2. Safety Instructions

- In case of damages caused by not
following this operating manual, the
warranty rights will expire! We exclude

!

handling or not following the safety instructions.

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily
reconstruct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade
cooperative association for electric plants and working material are to be
considered in industrial environments.

3. Usage in Accordance with Requirements

The light balls are automatically switched on at darkness and switched
out at morning light or in case the accumulators are empty. The maxi­mum duration of illumination with full accumulator and without recharge is
approx. 8 hours.
The solar modules installed in the upper part charge the built-in accumu­lator. In order to achieve a charge, it is required to expose the solar
modules to direct sunlight. A patented charging electronics “Ultimax”
ensures the optimum charge of the accumulator. The light fixture may be
used in sunny sun parlors where, however, the duration of illumination
might be shorter
The solar light is suitable for the outdoor usage and operation but should
be taken to the inside during the winter
lamp for this purpose.
Note: Make sure that the lamp is always adjusted to the south and sha­dows are avoided. The product may not be used if adjusted to the north.
In the winter

4. Initiation

1. Please carefully take all parts out of the package and remove the foils.

2. Carefully turn off the stainless steel floor stand from the upper parts
(Picture 1).

3. Switch to rocker switch beside the accumulator to the position “Auto”
(Picture 2).
Note: The lamp is switched-off in position “OFF” and the accumulator
is not charged.

4. Now, carefully put the stainless steel floor stand back to the upper part
and screw it (Picture 1).

5. The poles with the light balls may be flexed optionally.

The solar light is now activated.

Note:

reduced. Should the solar lights not illuminate in the first evening, wait for
a sunny day.

, it is required to keep the solar module free of snow.

The maximum illumination time in wintertime is normally somewhat

liability for any consequential damages!

- We exclude liability for property or
personal damages caused by inappropriate

.

. Please always switch off the

.

1

2.

open

lose

c

plug

switch

accu­mulator

5. Exchange of Accumulators

The capacity of the accumulator pack will reduce after one to two years
and thus, the accumulator has to be exchanged. This accumulator pack
can be purchased from your dealer or the manufacturer. The accumula­tor pack must exclusively be replaced by an equivalent accumulator
pack.

1. Unscrew the floor stand from the upper part (Picture 1).

2. Disconnect the white plug connection on the accumulator line (Picture

2).

3. Carefully take out the accumulator from the mounting bracket (Picture

2).

4. Now put the accumulator back into the bracket and reconnect the
cable (Picture 2).

Note: Used batteries should be disposed of environmentally friendly,
i.e. not as a part of domestic waste. Return them to the supplier, who

is obligated by law to take them back.

6. Malfunctions

- Lamp is not automatically switched on at darkness

- An outside light source (e.g. streetlight) simulates daylight and pre­vents the lamp from switching on. Place the lamp at a darker location.

- Accumulator weak or defective. Exchange of the accumulators.

7. Specifications

- Operating voltage: 3,6 V

- Battery: Li-ion 3,6 V/ 750 mAh

- Illuminating units: 5 white LEDs

- Illumination time: max. 8 h with a full battery

Manufacturer/Importer:

esotec GmbH, Etzenrichterstr. 14, D-92729 Weiherhammer

el.-Nr: 09605-92206-28, Fax.-Nr: 09605-92206-10,

T
e-mail:[e-mail]
Internet:www.esotec.eu

Product

Art.-Nr: 102602

(Replacement part.-No. 901003 www.esotec.de)

Battery take-back

Batteries must not be discarded into domestic

­waste.
The consumer is legally required to return batteries

­after use, e.g. to public collecting centers or to batte­ry distributors.
Contaminant-containing batteries are labeled with

­the sign “crossed-out trashcan“ and one of the che­mical symbols Cd (= battery contains cadmium), Hg
(= battery contains mercury), Pb (= battery contains lead). Used batte­ries should be disposed environmentally friendly and should not be
discarded into domestic waste. Your dealer is legally required to take
back old batteries.

Li-ion

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dispose of the
product in future, please consider that it contains valuable raw materials
suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a col
lection point for the recycling of waste electrical and electronic equip­ment.
Thank you very much for your cooperation!

Copyright, esotec GmbH

-