Esotec Solar LED User manual

Using Instructions

GB

Solar LED Alu-Wireball

These instructions relate ONLY to this product and contain important
information for using the product for the first time. Please keep these
instructions for later reference and should always accompany the
product in the event of transference to a new user.

1. Introduction

Dear Costumer,
Thank you for purchasing the solar light. With this solar light you purcha­sed a product manufactured according to the current state of technology.

This product fulfils all requirements of the valid European and nati-

the user will have to follow this operating manual!

2. Safety Instructions

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily
reconstruct and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade
cooperative association for electric plants and working material are to be

considered in industrial environments.

3. Intended Use and Function

The LED wire ball is automatically switched on at darkness and switched
off at morning light. With a fully charged battery and without recharging,
the maximum light ON time of the lighting amounts to approx. 10 hours.
The solar module installed in the upper part of the housing charges the
integrated rechargeable battery. The LED wire ball is switched on and off
via a switch. The LED wire ball is designed in IP 44 (splashproof) and
protection class III and is suitable for year-round outdoor operation. The
wire ball is made of aluminum wire.

Note: Please make sure that the wire ball is never lying in the water.

Note: Please make sure that the solar module is preferably directed to the

south and that shadows are avoided. The product can not be used when
directed to a north side. The solar module shall always be free from snow
during the winter.

4. Start-up

1. Please carefully take all parts out of the package.

2. In case the wire ball should not be really round due to transport or

onal regulations. The conformity was proved. The relevant
declarations and documentation are deposited with the
manufacturer.

To maintain this state and guarantee a safe operation, you as

- In case of damages caused by not
following this operating manual, the

warranty rights will expire! We exclude

liability for any consequential damages!

- We exclude liability for property or

!

storage, you may deform it slightly with your hands.

personal damages caused by inappropriate

handling or not following the safety instructions.

1.

5. Exchange of the rechargeable Battery

The capacity of the battery will diminish after one to two years and it will
have to be exchanged. The battery is available at your local retailer’s or
from the manufacturer. Please exclusively use an identical in construction
battery.

1. Put the switch on the bottom side into the position „OFF“

2. Unscrew the 8 screws on the bottom part of the housing and remove the
lid.

2. Loosen the screw on the battery compartment lid and remove the lid
(illustration 1).

3. Remove the battery from the holder.

4. Insert the new battery with correct polarity and close the housing in
reverse order.

5. Now put the switch to the position “C” or position “B” for ashing light.

6. Malfunctions

- Lamp is not automatically switched on at darkness

- An outside light source (e.g. streetlight) simulates daylight and prevents
the lamp from switching on. Place the solar module at a darker location.

- Lamp is not switched on at darkness or only for a short period of
time.

- Is the lamp connected?

- Accumulator weak or defective. Exchange of the accumulators.

7. Technical Data

• Solar module: crystalline, 1 Wp

• Rechargeable battery: NiMh 1.2 V/2000 mAh, Mignon (AA)

• Protection type: IP 44

• Protection class: III

• Illuminant: 50 white light emitting diodes (light color: 10000 K)

• Light time: max. 10 h will a fully charged battery

Manufacturer/Importer:

Battery take-back

- Batteries must not be discarded into domestic
waste.

- The consumer is legally required to return batteries
after use, e.g. to public collecting centers or to bat­tery distributors.

- Contaminant-containing batteries are labeled with
the sign “crossed-out trashcan“ and one of the che­mical symbols. Used batteries should be disposed
environmentally friendly and should not be discarded
into domestic waste. Your dealer is legally required to take back old
batteries.

NiMh

3. For permanent light, switch the toggle switch on the bottom side of the

solar module to the position “C” or position “B” for ashing light.

Note: The LED wire ball is switched off in position „OFF“ and the battery

is not charged.

4. The control unit may be inserted into the ground by means of the ground

spike or screwed to the oor or wall by means of the bracket.

The solar LED wire ball is now activated!

Note: The maximum illumination time in wintertime is normally somewhat
reduced. Should the solar lights not illuminate in the first evening, wait for
a sunny day.

esotec GmbH - Weberschlag 9 - D-92729 Weiherhammer
Tel.-Nr: [phone] Fax.-Nr: [phone]
e-mail: [e-mail] Internet: www.esotec.de

Product Art.-Nr: 102112

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dis­pose of the product in future, please consider that it contains
valuable raw materials suited for recycling.
Therefore, do not dispose it of with domestic waste but bring
it to a collection point for the recycling of waste electrical and
electronic equipment.
Thank you very much for your cooperation!

Copyright, esotec GmbH