Esotec Palermo-S User guide

Instruction manual

G

B

Solar pond pump set “Palermo-S”

Customer support:

f you have problems or questions regarding this product, simply contact us!

I

onday to Friday 8 am to 12 noon and 1 pm to 4 pm.

M

By phone: [phone]

y e-mail for ordering spare parts: [e-mail]

B

y e-mail for questions about the product: [e-mail]

B

roduct: Manufacturer Item No.: 101769

P

These instructions relate ONLY to this product and contain important informa-

ion for using the product for the first time. Please keep these instructions for

t

ater reference and should always accompany the product in the event of trans-

l

erence to a new user.

f

1. Introduction

ear Costumer, thank you for purchasing the solar pump kit.

D

ith this solar pump kit you purchased a product manufactured according to the cur-

W
rent state of technology.

his product fulfils all requirements of the valid European and national regula-

T

ions. The conformity was proved. The relevant declarations and documentati-

t

n are deposited with the manufacturer.

o

To maintain this state and guarantee a safe operation, you as the user will have to fol-

ow this operating manual!

l

2. Safety Instructions

- In case of damages caused by not following
this operating manual, the warranty rights

ill expire! We exclude liability for any

w
consequential damages!

We exclude liability for property or

!

ue to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct

D
and/or change the solar pump kit.

herefore, please keep to the operating manual.

T
The accident prevention rules of the association of the industrial trade cooperative
association for electric plants and working material are to be considered in industrial
environments

3. Appropriate Use

- The pumping system is designed for the outdoor use in garden ponds.

- Direct solar radiation is required for the correct function.

- The pumping system is characterized by its easy assembly. Tools are not requi­red for the assembly.

- The pump must not be used for the raising of drinking water.

- The performance may be adjusted via a controller on the pump.

- In order to safely interrupt the pumping it is required to interrupt the cable connec­tion between solar module and pump.

4. Assembly and Initiation

The pumping system consists of the following parts:

1 piece solar module, 1 piece submerged pump in the plastic housing with a 5 m
connecting cable, 4 pipes and 4 water nozzles.

1. Completely unroll the connecting cable on the pump.

2. Attach the telescopic ascending pipe onto the pump and then attach one of the
desired sprinklers onto the ascending pipe.

3. Put the pump in the pond on some stones. Avoid a location directly on the ground
of the pond because a lot of dirt is here sucked in by the pump which will then be
polluted very fast.

4. Now connect the plug of the pump with the socket of the solar module and screw
the cap.

Position the solar module in a sunny, shadow-free place facing south. You can use
the ground stick to mount the solar module.

Attention: Risk of injury! A broken module may not be repaired and has to be dispo­sed of environmentally sound.

Note: For further assembly instructions, please see the instruction of the water pump.

­personal damages caused by inappropriate
handling or not following the safety instructions.

- In these cases any guarantee rights will expire.

5. Dry run protection

The pump is equipped as standard with a dry run pro­tection. Two sensor points are provided on the side of

he housing for this. The pump works if these points are

t

nder water. If a point projects out of the water, the

u
pump does not work.

6. Service and Maintenance

n order to preserve the performance of the pump, it is required to wash out the pump

I
and its parts with warm water depending on the pollution of the water.

or directions for the service and maintenance of the pump storage, please see the

F

nstruction of the pump storage.

i

Occasionally wipe the solar module clean with a soft and slightly moistened cloth.

ote: Before carrying out operations on the pump, interrupt the plug connection bet-

N

een pump and solar module in order to avoid any unintentional starting during the

w
operations.

Sensorpoints

7. Technical Data

System voltage: 8 VDC

-

Solar module

- Nominal power: 3,5 Wp
Nominal voltage: 7,8 V

-

- Nominal current: 450 mA

- Open-circuit voltage: 7,8 V
Short-circuit current: 490 mA

­ Projection system: IP 65

­ Temperature range: -30°C to +75°C

-

ater pump:

W

Operating voltage: 6 to 9 V DC

-

- Current consumption (8 VDC): ap. 310 mA
Max. delivery height (8 VDC): ap. 80 cm

­ Delivery rate (bei 8 VDC): ap. 300 l/h

-

- Protection system: IP 68

- Temperature range: +4 to +40°C
Dry running: no

-

Note: Protect the pump from frost!

In cold winter months, it is required to take the pump out of the water and store it in
a warm place. The solar module may be left outside during the winter.

8. Safety Instructions:

DANGER for children! Keep children away from swallowable small parts (ascending

pipe and sprinklers) and the packaging material. Danger of suffocation!

WARNING: risk of stumbling! Lay the connecting cable so that it will not become a
trip hazard!

CAUTION Material damage! When setting up the solar module without module brak­ket, please pay attention to an adequate stability. The solar module may be damaged
in case of tipping or in case of an impact of a foreign object.

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dispose of
the product in future, please consider that it contains valuable raw
materials suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a
collection point for the recycling of waste electrical and electronic
equipment.
Thank you very much for your cooperation!

Manufacturer / Importer

esotec GmbH - Gewerbegebiet Weberschlag 9 - D-92729 Weiherhammer

Tel.-Nr: [phone] - Fax.-Nr: [phone] - Internet: www.esotec.de

Copyright, esotec GmbH