Esotec Fontana User manual

Operating manual

GB

waterpump “Fontana”

Customer support:

If you have problems or questions regarding this product, simply contact us!
Monday to Friday 9 am to 12 noon and 1 pm to 4 pm.
By phone: [phone]
By e-mail for ordering spare parts: [e-mail]
By e-mail for questions about the product: [e-mail]

Product: Manufacturer Item No.: 101751

These instructions relate ONLY to this product and contain important infor­mation for using the product for the first time. Please keep these instructions
for later reference and should always accompany the product in the event of
transference to a new user.

1. Introduction

Dear Costumer,
Thank you for purchasing this product. You purchased a product manufactured
according to the current state of technology.

This product fulfils all requirements of the valid European and national regula­tions. The conformity was proved. The relevant declarations and documentati­on are deposited with the manufacturer.

To maintain this state and guarantee a safe operation, you as the user will have to
follow this operating manual!

2. Safety Instructions

- In case of damages caused by not

following this operating manual, the

warranty rights will expire! We exclude

liability for any consequential damages!

- We exclude liability for property or

!

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct
and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade cooperative
association for electric plants and working material are to be considered in industrial
environments.

personal damages caused by inappropriate

handling or not following the safety instructions.

5. Care and maintenance

For optimum performance of the pump, it must be washed occasionally with warm
water depending on the water contamination. To wash the pump, open the housing
as follows:

Note: Please do not use force while dismantling or assembling the pump. The parts
are very fragile and can break easily.

1. Disconnect the pump’s plug.

2. Pull the front cover of the pump forward like a slide gently (Figure 1).

3. Turn the front cover of the pump by about 45° clockwise (Figure 1) and carefully
pull the cover forward (Figure 2). Watch out for the plastic shaft and the seal while
doing this.

4. Carefully drag the impeller out of the pump (if necessary, use pliers). (Figure 3).

5. Now clean all the parts carefully with warm water.

6. Then plug the shaft with the impeller carefully into the hole of the pump. Ensure
that the shaft is fitted firmly.

7. Now place the cover carefully over the pump. Ensure that the seal is fitted proper­ly.

8. Turn the front cover again by 45 degrees counter-clockwise into the starting posi­tion.

9. Slide the lower part of the pump completely into the pump housing.

The pump is ready to use again.

1

3

turn 45°

2

3 inside

4

4+5

2

1

7

6

7

6. Malfunction

Pump is not pumping water

- Is the pump completely submerged in water?

- Is the pump dirty? Cleaning the pump, see Point 5.

3. Intended use

This submersible pump is designed for pumping water in garden ponds, fountains,
water dishes, etc. It can pump water through a hose connection or can be operated
through attached lifting tubes with water sprinklers.

The delivery rate of the pump can be adjusted using the regulator on the front side of
the pump. The water pump has no On/Off switch. As soon as the pump is connected
to its power supply, it starts pumping water.

4. Installation and commissioning

1. Roll out the connecting cable of the
pump completely.

2. Place the pump in water.

3. Connect the lifting tubes till they project
out of the water surface. For this, first
attach the reducer to the pump.

4. You can now choose from 3 different
water nozzles or a single jet nozzle.
The multiple jet nozzle attachments are
always snapped onto the nozzle cup.

5. Alternatively, the pump can also be used
for pumping water through a hose. For
this, you just have to attach a hose to the

pump’s pipe.

6. Now supply power to the water pump
through a solar module. Put the connec­tor from solar module and pump together.

Note: The plug has reverse-polarity protection, no force should be used while inser­ting. The glass of the solar module is fragile.
Caution! Risk of injury! A broken module cannot be repaired again and must be
disposed off in an environmental-friendly way.

7. If the pumping capacity is too high, you can reduce the amount of water. Simply
turn the regulator on the front side of the pump in clockwise direction. Please do
not use force while adjusting. The adjustment range is 45°.

lifting tubes

water nozzle

lifting tubes

reducer

water nozzles

7. Technical data

- Operating voltage: 17 V DC

- Degree of protection: IP 68

- Power consumption: 3,7 W - 4,5 W

- Pump lift: max. 1,2 m

- Delivery rate: max. 350 l/h

- Operating temp. range: +4 to +40°C

8. Spare parts (Figure 4)

1. White ceramic shaft: Item No.: 911002

2. Pump impeller: Item No.: 911003

3. Internal rubber bush: Item No.: 911004

4. Front cover: Item No.: 911005

5. Seal for cover: Item No.: 911006

6. Sliding carriages with suction bases: Item No.: 911007

7. Suction bases (4 pieces) Item No.: 911008

8. Complete nozzle set: Item No.: 911009

Manufacturer/Importer

esotec GmbH - Gewerbegebiet Weberschlag 9 - D-92729 Weiherhammer

Tel.-Nr: 09605-92206-0 - Fax.-Nr: 09605-92206-10 - Internet: www.esotec.de

Disposal:

Dear customer,
please cooperate in avoiding waste. When you intend to dispose of the
product in future, please consider that it contains valuable raw materials
suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a col­lection point for the recycling of waste electrical and electronic equipment.
Thank you very much for your cooperation!

Copyright, esotec GmbH