Escort 432 User Manual

Features and Monitor Controls

Monitor Installation

Camera Installation

R E A R V I E W C A M E R A S Y S T E M

Owner ’s Manual

Monitor

Speciﬁcally designed for passenger cars, trucks and SUVs.

• Supports single camera input.

• High-low voltage and short-circuit protection.

• Suction cup bracket installation.

• Automatically displays reverse camera view when reverse gear

is engaged.

Camera

• CMOS camera in mini size.

• Three-color proximity guide.

• Operates over a wide temperature range.

System power ON/OFF

• Install the monitor on the windshield of the car.

• Don’t install the monitor in an extremely hot or humid place

(radiator, air duct, etc.) or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

• The monitor is not waterproof.

Attach the supplied bracket to the glass or ﬂat area and make sure it’s ﬁrmly aﬃxed.

First, ﬁnd the best position and angle.

Second, rotate

the bracket and

ﬁx it ﬁrmly.

Adjust the angle of the monitor and

fasten the back

screw ﬁrmly.

• Use a silicon waterproof tape to wrap the connector of camera

and extension cable to ensure waterproof

• Protect the cable by using conduit or running the cable inside the

vehicle as much as possible

432

Cleaning and General Maintenance Connection Speciﬁcations and Service

Wiring Diagram

• Connect the RED wire to the 12V or 24V DC power terminal which

is energized with the ignition key in the accessory position.

• Connect the BLACK wire to a suitable negative connection point

on the vehicle

• Connect the GREEN wire to the switched power output terminal

of the “R” (revers

e) gear. Trigger is always in priority.

CAUTION:

Before making connections, disconnect the ground

terminal of the car battery to avoid a short circuit.

The plugs should be fully inserted into the connectors or jacks. A loose connection may cause malfunctioning of the unit.

If your vehicle has been parked in direct sun light resulting in a considerable rise in temperature inside the vehicle, allow the unit to cool oﬀ before operating. Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the ﬁnish of the unit.

Cleaning

Unplug or power oﬀ before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Ventilation

Holes in the housing and the back or bottom are provided for ventilation, and to ensure reliable operation of the monitor equipment for protection from overheating. These holes must not be blocked or covered.

Object and Liquid Entry

Never push objects of any kind into the monitor equipment through holes as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. Never spill liquid of any kind.

Servicin

Do not attempt to service this system by yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualiﬁed service personnel.

SPECIFICATIONS

Monitor

LCD proﬁle widescreen ratio .............................................................4:3

Wide view angle (CR) ..........20/50 (up/down), 40/40 (left/right)

Resolution ........................................................................230x400 pixels

Brightness (cd/m2) ...............................................................................250

Contrast ratio ..........................................................................................300

Response time (ms) (at 25°C) ...............................................................20

Power requirement ...........12VDC, with control box (12/24VDC)

Power consumption ........................................................................... ≤2W

Operating temperature range ................................... -20°C to +70°C

Storage temperature range ........................................-30°C to +80°C

Dimensions (mm) .............................................95 (L) x 75 (W) x 16 (D)

Weight (approx.) (gm) ............................................................................80

SERVICE

To obtain service: Contact ESCORT (800-543-1608) to obtain a Return Authorization

Number. Properly pack your product and include: your name, complete return address, written description of the problem with your product, daytime telephone number, and a copy of the original purchase receipt. Label the outside of the package clearly with your Return Authorization number. Ship the product prepaid (insured for your protection) to: ESCORT Inc., 5440 West Chester Road, West Chester, OH 45069.

Out-o f-warranty repairs:

For out-of-warranty repairs, include prepayment in the amount you were quoted by the ESCORT Customer Service Representative. If your SmartSite Mini has been damaged, abused, or modiﬁed, the repair cost will be calculated on a parts-and-labor

basis. If it exceeds the basic repair charge, you will be contacted with an estimate. If the additional payment is not received within 30 days (or if you notify us that you do not wish to have your SmartSite Mini repaired at the price quoted), the unit will be returned without repair. Payment can be made by check, money order, or credit card.

Features, speciﬁcations and prices subject to change without notice.

8765

Escort 432 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual