Ericsson LG WP-1000N User Manual

Step 4 –After the profile is saved, click the “Activate” button on Profile Page to active the
profile.

☉ Example 4:WPA/WPA2

Step 1 – Choose “WPA” or “WPA2” authentication type
Step 2 – Choose “TKIP” or “AES” encryption type

66

Step 3 –After the profile is saved, click the “Activate” button on Profile Page to active the
profile.

Step 4 –The Windows profile setting dialog is popped-up for user to modify.

67

3.2.4 Statistics

Statistics page displays the detail counter information based on 802.11 MIB counters. This
page translates the MIB counters into a format easier for user to understand. You may reset
the counters to Zero by clicking “Reset Counter”.

[Transmit Statistics]

Frames Transmitted Successfully: Frames successfully sent
Frames Transmitted Successfully After Retry: Frames sent successfully with retry.
Frames Fail to Receive ACK After All Retries: Frames failed transmit after hitting retry limit.
RTS Frames Successfully Receive CTS: Successfully receive CTS after sending RTS

frames.
RTS Frames Fail To Receive CTS: Failed to receive CTS after sending RTS frames.

[Receive Statistics]

Frames Received Successfully: Frames received succe ssfully.
Frames Received with CRC Error: Frames received with CRC error.
Frames Dropped Due to Out-of-Resource: Frames dropped due to resource issue.
Duplicate Frames Received: Duplicate received frames.

68

3.2.5 WPS Configuration

The primary goal of Wi-Fi Protected Setup (Wi-Fi Simple Configuration) is to simply the
security setup and management of Wi-Fi Networks.

WPS Associate IE: If the “WPS Associate IE” option is checked, station will send the
association request with WPS IE during WPS setup.
WPS Probe IE: If the “WPS Probe IE” option is checked, station will send the probe request
with WPS IE during WPS setup.

[Display WPS capable AP information]

The WPS capable AP information is listed in the upper frame, and the display AP’s characters
are SSID, BSSID, current operating channel, device password ID, authentication type, and
encryption type.
Re-Scanning: Clicking “re-scan” button performs the re-scanning action.
WPS AP Information: Clicking the WPS information” button brings up the WPS capable AP
information dialog.

 Authentication Type: there are three type of supported authentication modes, and

there are Open, Shared, WPA-PSK and WPA modes.

69

 Encryption Type: For Open & Shared authentication modes, the available

encryption types are None and WEP. For WPA, WPA2, WPA-PSK and WPA2-PSK
authentication modes, the available encryption types are TKIP and AES.

 Config Methods: This attributes contains the config methods supported and

enabled by the selected Registrar.

 Device Password ID: Device Password ID indicates the method or identifies the

specific password that the selected Registrar intends to use.

 Selected Registrar: Selected Registrar indicates if the user has recently activated a

Registrar to add an Enrollee.

 State: This attribute is used to indicate the current configuration state. This attribute

is either “Un-Configured” or “Configured”.

 Version: This attribute is the specified WPS version.
 AP Setup Locked: AP Setup Locked indicates if AP has entered a setup locked

state.

 UUID-E: UUID-E is the universally unique identifier (UUID) generated by the

Enrollee.

 RF-Bands: RF Bands indicate the available RF bands.

[Configure WPS Profiles]

The user can configure WPS profile with either PIN method or PBC method.

 PIN Method:

Step 1 Î The Registrar enters the pin code generated by station.
Step 2 Î Click the “PIN” button.

 PBC Method:

Step 1 Î Click the “PBC” button within 2 second while the Registrar clicks the
button.

[Manage WPS Profiles]

The Received WPS profiles are listed in the lower frame, and the listed WPS profile attributes
are SSID, MAC address, authentication type, and encryption type.

 WPS profile detail information: Selecting a profile then clicking the “Detail” button

brings up the WPS profile detail information dialog.

 Connect with WPS Profile: Clicking the “Connect” button will connect to AP with the

select WPS profile.

 Rotate WPS profile: If there are more than two WPS profiles, clicking the “Rotate”

button will rotate to next profile and connect to AP with this profile. If the connection
can’t be made successfully, station will perform the WPS profile rotation repeatedly.

 Disconnect from WPS AP: Clicking the “Disconnect” button will stop the WPS

70

connection.

 Delete WPS profile: Clicking the “Delete” button will delete the selected WPS profile.

3.2.6 QoS

The QoS Page of RaConfig. It involves “WMM Enable”, “WMM – Power Save Enable” and
“DLS setup Enable”.

☉Configure to enable Wi-Fi Multi-Media

If you want to use “WMM – Power Save” or “Direct Link”, you must enable WMM. The
setting method of enabling WMM indicates as follows:

Step1: Click “WMM Enable”
Step2: Click “Apply”.

71

Step3: Change to “Site Survey Page”. And add an AP that supports WMM features

to a Profile. The result will look like the below figure in Profile page.

72