Ericsson MDR GE-MARC Maintenance Manual

Download

Maintenance Manual

LBI-38952A

Printed in U.S.A

Mobile Communications

MDR GE-MARC MOBILE RADIO

TABLE OF CONTENTS

DUPLEXER INTERFACE BOARD . . . . . . . . . . . . . . . . . . LBI-38700

RF BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38841

SYSTEM BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38842

LOGIC BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38392

AUDIO BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38391

AUDIO AMPLIFIER BOARD . . . . . . . . . . . . . . . . . . . . . LBI-38844

HANDSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38698

SERVICE SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . LBI-38953

Continued

TABLE OF CONTENTS

Page

SPECIFICATIONS............................................ .... .... . .... .... .... .... ... .... .... .... .... . .... .... .... .... ... .... .... .................................. 2

GENERAL DESCRIPTION................................... ......................................................................... ......................... .. 3

RF BOARD ......... ................................... .............................................................................................................. 3

Synthesizer Circuit....................................................................................................................................... 3

Transmitter Circuit ....................................................................................................................................... 3

Receiver Circuit............................................................................................................................................ 3

DUPLEXER INTERFACE/TALK-AROUND BOARD ................................................................................... 3

LOGIC BOARD .................................................................................................................................................. 3

SYSTEM BOARD ............................................................................................................................................... 3

FRONT CAP ASSEMBLY..................................................................................................................................

ACCESSORIES AND OPTIONS .............................................................................................................................. 3

PC PROGRAMMER OPTIONS......................................................................................................................... 3

PC PROGRAMMED OPTIONS ........................................................................................................................ 3

Carrier Control Timer (CCT)....................... ......................... . .. ............. . .............. ............. . .............. ............ 3

Channel Guard.............................................................................................................................................. 3

Squelch Tail Elimination (STE)................................................................................................................... 3

Hook Switch Programming Option............ ............ ............ ............ ............ ............ ............ ............ ............ . 4

Retry Option ................................................................................................................................................. 4

HARDWARE AND HAR DWARE OPTIONS...................................... ..... .... .... .... .... .... .... .... .... .... .... ....... .... .... .... .... 4

HANDSET ........................................ .... .... .... .... .... .... .... .... .... ....... .... .... .... .... .... .... .... .... .... .... ..... .... .... .... .... .... .... ... 4

HANDSET CABLING OPTIONS...................................... . ... . ... . .... ... . ... . .... ... . ... . ... .... . ... . ... .... . ... . ... . .... ... . ... . .... ... 4

OPTION CABLE................................................................................................................................................. 4

NOISE SUPPRESSION KIT OPTION .............................................................................................................. 4

POWER CABLE OPTION ................................................................................................................................. 4

EXTERNAL SPEAKER OPTION ...................................... ... . ... . ........................ ... . ... ........................ . ... . ........... 4

EXTERNAL ALARM ..................................... ......... ............ ........... ......... ............ ........... ......... ........... ............ .... 4

SYSTEM DESCRIPTION.......................................................................................................................................... 4

OPERATIONAL MODES....................... . . ...................................... ..................................... . . . ............................ 4

IDLE MODE............................ . .... ... .... .... . .... ... .... . .... ... .... . .... .... ... .... . .... ... .... . .... ... .... .... . .... ... .... . .... ... .... . .... .... ... .... 5

WAIT MODE....................................................................................................................................................... 5

READY MODE ................................................................................................................................................... 5

GLOSSARY OF SYST EM TERMS.......................................................................................................................... 7

RADIO OPERATION................................................................................................................................................. 7

VISUAL INDICATORS ............. ................................................................... ...................................................... 7

ALPHANUMERIC STATUS INDICATORS..................... . ... ......................... ... . ... . ... . ... ......................... ... . ... . ... 7

Busy........................................ ... . ... . ... . ... . ... ......................... ... . ... . ... . ... ......................... ... . ... . ... . ... .................... 7

Retrying............................................. . ........................... . ... . ... . ... . ........................... . ... . ... . ... . ........................... 7

Wait................. ... . ... . ... ......................... ... . ... . ... . ... ......................... ... . ... . ... . ... ......................... ... . ... . ... . ... . ........... 7

TABLE OF CONTENTS

(Continued)

Page

STATUS INDICATORS............................................................................................................................... 7

No Service.............................................................................................................................................. 7

Roam ...................................................................................................................................................... 7

Function ................................................................................................................................................. 7

Bar Status Indicators (|||||)..................................................................................................................... 7

Horn........................................................................................................................................................ 7

Mute ....................................................................................................................................................... 7

Lock............................. . .... .... ... .... .... . .... ... .... .... . .... .... ... .... .... . .... ... .... .... . .... .... ... .... .... . .... ... .... .... . .... .... ... ... 7

AUDIBLE INDICATORS................ . .. . . ... . .. . . ... . . .. . .. . . ... . . .. . .. . . ... . .. . . ... . . .. . .. . . ... . . .. . .. . . ... . .. . . ... . . .. . .. . . ... . . .. . .. . . ... . .. . . ... . . . 7

SELF CHECK TEST ALERT............................................ ... . ... . ........................... . ... . ... . ... . .......................... 7

CALL RECEIVED ALERT......................................................................................................................... 7

CALL ORIGINATE ALERT........................................................................................................................ 7

SYSTEM BUSY........................................................................................................................................... 7

OUT OF RANGE ALERT............................................................................................................................ 7

INVALID CALL ORIGINATE ALERT...................................................................................................... 8

CARRIER CONTROL TIMER .................................... . .... ... . .... ... .... . .... ... . .... ... .... . ... .... . .... ... .... . ... .... . .... ... . .. 8

GE-MARC SYSTEM TONES..................................................................................................................... 8

KEY DEFINITIONS/FUNCTIONS................................................................................................................... 8

MISCELLANEOUS KEYS ......................................................................................................................... 8

Power ..................................................................................................................................................... 8

Push-To-Talk.......................................................................................................................................... 8

Volume Up............................ . .... ... . ... . .... ... . ... . .... ... . ... . .... ... . ... . .... ... . ... . .... ... . ... . .... ... . ... . .... ........................ 8

Volume Down........................ ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... .... . ... . ... . 8

FUNCTION KEYPAD................................................................................................................................. 8

Send........................................................................................................................................................ 8

Clear (CLR) ........................................................................................................................................... 8

End ..................................................................... .................................................................................... 8

Recall (RCL).......................................................................................................................................... 8

Store (STO)............................................................................................................................................ 8

Alphabet Keys (A, B, C)....................................................................................................................... 8

Function (FCN) ..................................................................................................................................... 8

NUMERIC KEYPAD................................................................................................................................... 8

0-9 ......................................................................................................................................................... 8

Asterisk(❉)............................................................................................................................................ 8

Pound (#)................................................................................................................................................ 8

TELEPHONE EXTENDED FEATURES........................................................................................................... 8

LBI-38952 LBI-38952

TABLE OF CONTENTS

(Continued)

Page

BASIC OPERATION.......................................................................................................................................... 9

VOLUME ADJUSTMENT...................... ............ ............ ............ ............ ............ ............ ............ ............ . 9

AREA SELECTION.................................................................................................................................. 9

GROUP SELECTION............................................................................................................................... 9

CHANNEL ACTIVITY ............................................................................................................................ 9

PLACING A DISPATCH CALL............ . ............ ............ ............ ............ ............ ............ ............ ............ .. 9

PLACING AN INTERCONNECT OR DISPATCH OVERDIAL CALL.................................... .......... 9

ENDING A CALL ..................................................................................................................................... 9

RECEIVING A CALL............................................................................................................................... 9

DIRECT MODE OPERATION ................ .... . .... .... .... .... ... .... .... .... .... . .... .... .... .... ... .... .... .... .... . .... .... .... .... ... 9

CONVENTIONAL MODE OPERATION............................................................................................... 9

Call Timer........................ . .... ... . ... . ... .... . ... . ... .... . ... . ... . .... ... . ... . .... ... . ... . ... .... . ... . ... .... . ... . ... . .... ... . ... . .... ... . ... . . 10

Last Digit Clear And Display Clear ................ ... ............. . .. ............. . .. . . .. ............. . .. . . .. . . .. ............. . .. . . .. .. 10

Storing Numbers ................................................................................................................................... 10

Recalling Numbers................................................................................................................................ 10

Hot Keys................................................................................................................................................ 10

Last Number Redial ..................................... ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . . 10

Locking The MDR Mobile Radio ........................................................................................................ 10

Backlight................................................................................................................................................ 10

Horn ....................................................................................................................................................... 10

External Speaker................................................................................................................................... 10

Call Hold (Mute)................................................................................................................................... 10

Simplex Operation ................................................................................................................................ 10

DTMF Digit Length ..................................................... ... . ... ........................ . ... . ........................ ... . ... . ..... 10

Delay After DTMF Star (❉) ....................... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . ... . . 10

CHANNEL GUARD TONE FREQUENCIES .................................................................................................. 10

DIGITAL CHANNEL GUARD TONES............................................................................................................ 11

PARTS LIST.................................... ... . ... . ... ......................... ... . ... . ... . ... ......................... ... . ... . ... . ... . ......................... 11

ASSEMBLY DIAGRAM .... ..... ....... ..... .... ....... ..... ....... ..... .... ....... ..... ....... ..... .... ....... ..... ....... ..... .... ....... .... ........ .... 12

INTERCONNECTION DIAGRAMS:

800 MHz DUPLEX MOBILES (SYSTEM)............................................................................................ 15

STANDARD 800 MHz DUPLEX MOBILE .............................. ... . ... . ... . ... . ... ........................ . ... . ... . ... . ..... 16

800 MHz DUPLEX WITH TALK-AROUND......................................................................................... 17

800 MHz DUPLEX MOBILE (OPTIONS)............................................................................................. 18

SPECIFICATIONS*

GENERAL

Operating Voltage 13.8 Volts ±20% Battery Drain

Receiver (13.8 Vdc)

Off 0.01 Amperes (maximum) Squelched 0.8 Amperes (maximum) Unsquelched 3.5 Amperes (maximum at 10 Watts audio)

Transmitter (13.8 Vdc) 6.0 Amperes (maximum at 10 Watts RF)

Channel Spacing 25 kHz Frequency Stability ±1.5 PPM (±0.00015%) Temperature Range -30°C to +60°C (-22°F to +140°F) Dimensions (H x W x D)

Height 5.3 cm (2.1 inches) Width 18.2 cm (7.2 inches)

Depth 24.0 cm (9.5 inches) Weight 3.0 kg (6.6 pounds) Antenna Impedance 50 Ohms

TRANSMITTER

Frequency Range 806.0125-820.9875 MHz

851.0125-865.9875 MHz (with Talk-around option only)

Output Power 10 Watts (100% duty cycle) Audio Sensitivity 200-300 mVrms Spurious an d H a rm o ni c s <-16 dBm Audio Distortion 5% maximum Modulation Limiting +5 kHz maximum FM Hum and Noise -42 dB Audio Frequency Response Within +1, -3 dB of a 6 dB/octave pre-emphasis curve per EIA Standards from 300-3000 Hz

RECEIVER

Frequency Range 851.0125-865.9875 MHz Acceptable Frequency Displacement ±2.0 kHz (minimum) Sensitivity (12 dB SINAD) -113 dBm minimum in duplex Spurious Response 70 dB minimum Adjacent Channel Selectivity 65 dB minimum ±25.0 kHz Intermodulation 60 dB minimum

Audio Frequency Response Within +2, -8dB of a 6 dB/octave de-emphasis curve

from 300-2700 Hz Audio Output 10 Watts Audio Distortion 5% maximum at 1000 Hz.

*These specifications are intended primarily for use by service personnel. Refer to the appropriate Specification Sheet

for complete specifications.

LBI-38952 LBI-38952

GENERAL DESCRIPTION

The Ericsson GE-MARC V•E MDR Mobile Radio is a

synthesized, wideband radio uses integrated circuits and microcomputer technology to provide high performance trunked and conventional operation. The radio provides 10 Watts of RF power output in the 806.0125-820.9875 MHz and 851.0125-

865.9875 MHz bands. The receiver operates in the 851.0125-

865.9875 MHz band.

All radio functions are stored in a programmable Electri-

cally Erasable PROM (EEPROM). The radio is field program- mable using an IBM compatible personal computer with the following equipment:

• Serial Programming Interface Module TQ3310

or TQ3370

• Programming Cable (19B801417P9) TQ3371

• MDR Series Programming Software TQ3355

With the interface equipment and software, the computer can be used to program (or re-program) customer system frequencies, Channel Guard tones and options. Selection of options is done during radio initialization using the PC programmer.

The MDR Mobile Radio assembly contains the following circuit boards and assemblies:

• Duplexer Interface Board A4 19D903504G2

• Talk-Around Board A4 19D903507G2

• RF Board A2 19D902123G20

• System Board A5 19D901891G3

• Logic Board A1 19D902172G2

• Audio Board A3 19D902188G3

• Audio Amplifier Board 19D904025G1

• Handset A8 344A3783P2

• Duplexer 806-870 MHz 19B801362P3

The circuit boards are all mounted on a main casting to provide easy access for ser vicing. Inte rconnect plugs ar e used to connect the boards to eliminate pinched wires and other wiring problems.

RF BOARD

The RF board includes the programmable freq uency synthe-

sizer, transmitter exciter, receiver front end an d IF circuitry.

Synthesizer Circuit

The synthesizer generates all transmit and receive RF frequencies. The synthesizer frequency is controlled by the microprocessor located on the Logic Board. Frequency stability is maintained by a temperature compensated reference oscillator module. Transmit audio is processed on the Audio and Logic Boards, and applied to the synthesizer to m odulate th e VCO and TCXO. The buffered VCO output drives both the transmitter exciter and the receiver mixer.

Transmitter Circuit

The transmitter consists of a fixed-tuned exciter module, a PA module and a power control circuit. The PA module provides an RF output to drive the duplexer. The power control circuit controls the PA module by processing a DC signal from the duplexer interface board to maintain constant output power across the band. The RF output level is internally adjustable for rated power. Thermistors in the control circuit protect the PA from overheating by reducing the power output level.

Receiver Circuit

The dual conversion receiver circuit consists of a front end section, 45 MHz first IF, a 455 k Hz s econd IF, a n d FM d etect or. All audio processing and squelch functions are accomplished on the Audio Board.

DUPLEXER INTERFACE OR TALK-AROUND BOARD

Two versions of this board exist. The standard duplexer interface board contains only a directional coupler and the Talkaround board contains a directional coupler and RF switching circuitry to provide talk-around tran smit capability. Radio p ower distribution is also present on these boards. The directional coupler samples the duplexer output and provides a DC signal proportional to the detected power to the RF board power control circuitry.

AUDIO BOARD

The Audio Board provides analog to digital and digital to analog conversion of the receive and transmit audio for digital processing by the Logic Board. The board also contains analog

audio filtering, conventional analog tone processing, and the receiver squelch.

LOGIC BOARD

The Logic Board controls the operation of the radio and digitally processes the receive and transmit audio. The board contains a microprocessor and associated memory circuits including an EPROM for controlling the processor and a programmable "personality" memory (an Electrically Eras- able PROM - EEPROM) to store customer frequencies, tones, and options. The microprocessor provides control data to the Digital Signal Processor (DSP), conventional tone generation and detection, frequency data for the synthesizer, and sends and receives data to/from the handset for the LCD display and the keypad commands.

SYSTEM BOARD

The system board controls the main input power to the radio. The handset POWER switch and the IGNITION SENSE input lead provide the necessary signal s to t h e M O SFET switching circuit. The board also interfaces all option connections from the internal boards in the radio with the optional items outside of the r adio. All ex ternal options for the radio interconnect to the System Board through the back o f the radio using an optional cable.

FRONT CAP ASSEMBLY

The front cap assembly contains the Audio Amplifier board. The Audio Amplifier board provides compression of the microphone audi o fro m th e han dset . It a lso pr ovides a udio compression for the received audio from the discriminator to handset speaker audio and external speaker audio paths. A 10-watt power amplifier is provided on the Audio Amplifier board to drive a 4-ohm external speaker. Separ ate mute control for the external speaker and handset audio are provided.

ACCESSORIES AND OPTIONS

PC PROGRAMMER OPTIONS

The radio is programmed using an IBM or compatible personal computer equipped with a RS-232 port. Options TQ3310 or TQ3370 provide the RS-232 serial interface unit and the cable between th e PC and th e unit. An au xiliary po wer supply for the unit is also included which is not needed to program the MDR.

Option TQ3371 provides the radio programming cable between the PC interface unit and the radio handset jack. MDR

PC programming software Option TQ3355 provides both the

3.5 inch and 5.25 inch diskettes.

PC PROGRAMMED OPTIONS

Carrier Control Timer (CCT)

The Carrier Control Timer turns off the transmitter after the handset push-to-talk (PTT) switch has been keyed for a pre-programmed time period. A pulsing alert tone will warn the operator to unkey and then rekey the PTT to continue the transmission. The timer can be programmed, using the PC programmer to time out for 30 seconds to 7.5 minutes in 30 second increments . The ti mer c an be ena bled or dis abl ed for each channel.

In Duplex mode a quick 2-note alert is heard at t he interval of the carrier timer to let the user know that interval has elapsed.

Channel Guard

Channel Guard provides a means of restricting calls to specific radios through the use of a Continuous Tone Coded

Squelch System (CTCSS), or a Continuous Digital Coded Squelch System (CDCSS). Channel Guard may be used only

in the conventional mode, not in the GE-MARC trunked mode. Tone frequencies range from 67.0 Hz to 210.7 Hz in 0.1 Hz steps. There are also 83 standard PC programmable digital codes. The Channel Guard tone frequencies and codes are software programmable. Tone frequencies and digital codes cannot be mixed on the same RF frequency/channel. However, multiple channels can be programmed with the same frequency and different CG tones or DCG codes. These codes and frequencies are listed in Table 1 - Channel Guard Tone Frequencies and Table 2 - Digital Channel Guard Codes (refer to the Table Of Contents).

Squelch Tail Elimination (STE)

STE is used with tone and digital Channel Guard to eliminate squelc h t ails. T he S TE burst is tr ansm itted w hen t he handset PTT is released. The receiving radio decodes the burst and mutes the receiver audio for 250 msec. This mute time allows the transmission to end and to mute the squelch tail. The radio looks for STE on the received signal when the handset is either on or off-hook. The STE is enabled for transmit and/or receive by PC programming the radio’s personality.

LBI-38952 LBI-38952

Hook Switch Programming Option

"Off Hook Call" originate and "On H ook C all" termi-

nate can be enabled using the PC programmer. When this option is enabled placing the handset on the handset holder terminates a call. When origin ating a call, the number to be called can be keyed in, or recalled from memory, and when the handset is removed from the holder the call will be i nitiated without further user inte rvention. When placing a trunked

SPECIAL CALL mobile-to-land interconnect cal l, the ON HOOK CALL TERMI NATE feature cannot be disabled.

When hanging up on an interconnect call, it will al ways terminate the call and disconnect. This feature is only usable in the trunked dispatch mode.

Retry Option

If no channel is free, the radio can be programmed to activate the Call Retry state and display ’RETRYING’ in the display. Retrying will cause the radio to revert to the Idle mode and scan for an incoming call while trying to acquire a free repeater approximately eve ry 5 seconds f or a 2 m inute per iod.

HARDWARE AND HARDWARE

OPTIONS

(Sheet 4 of the MDR 800 MHz Duplex Mobile I nter connect Diagram illustrates the possible options and their placement in the system).

HANDSET

The handset, PMHS3U (344A3783P2), contains a micr ocontroller which interfaces the keypad and Liquid Crystal Display (LCD) to two serial data lines. The serial data lines allow communication with the radio microcontroller on the logic board through a 300 baud link using TTL signals. All messages are inverted 8 bit ASCII.

When the handset display is updated, the logic board passes data over the serial link. When a button, including the PTT switch (except the power button) is pressed, the code for the selected key is sent to the logic board. When no data is transmitted, the two-wire link remains at a high logic level. The power button directly controls the toggle flip-flop on the system board which passes power to the entire radio (including handset power).

HANDSET CABLING OPTIONS

Handset extension cable, Option PMCC1H (19B801636P1), is 18’ long and can be used to augment the

standard 3’ handset cable, Option PMCD1M ( 19B802397P1). In-line connector, Option PMCN1A (19A705839P1), m ust be used to mate the cables. It is recommended that Handset Extension Cable Kit, Option PMZM5V, be used in remote mount applications.

OPTION CABLE

Option Cable Option PMCD7Z (19C851585P14) is used to bring all option connections f rom the System Board through the back of the radio to the outside. This c able is requ ired with all external options.

NOISE SUPPRESSION KIT OPTION

Noise Suppression Kit Option PMPD1A (19A148539G1) is available for installations where e xcessiv e alternator or electrical noises, present on the power cable, interfere with proper radio operation. R efer to the inter connect diagram for the radio and options.

POWER CABLE OPTION

18-foot power cable Option PMCD9A, (19B801358P17) is available for installations requiring more th an the standard 9-foot cable.

EXTERNAL SPEAKER OPTION

External Speaker and Cable Option PMZM1K provides the user with a five-inch weatherproof speaker in a LEXAN housing. PMCC9M is an 18 inch interconnecting cable for the speaker. The radio’ s 10-watt ampl ifier drives the speaker’s 4-ohm impedance. The speaker leads are connected to pins 2 and 9 of Option Cable, Option PMCD7Z (19C851585P14), using External Speaker Cable, Option PMCC9M (19A149590P8) (18 inches) included in the PMZM5T kit. A 16-foot cable, Option PMCD1W (19A149590P10) is also available.

EXTERNAL ALARM

External Alarm Horn Relay, Option PMSU1C (19A705499P1) connects to pin 13 of Option Cable PMCD72 (19C851585P14). The relay can sound the vehicle horn when a call is received. The handset can disable or enable the horn relay option.

SYSTEM DESCRIPTION

The GE-MARC V•E trunked mobile radio system permits

improved access to available RF channels, freedom from annoyance by other users’ conversations and a degree of privacy for the user. The trunked mobile radio system consists of a repeater for each channel and the users’ mobile radio units. The system uses tone signalling with each mobile being assigned two and/or four tone group tone sequences . Groups of mobil es ar e assigned the same tones, so that any unit can talk to all other units in the same group. A block diagram is shown in Figure 1.

When originating a call, the mobile identifies an idle repeater channel and interrogates it with a single burst of "busy tone", the repeater keys its transmitter and sends a burst of "acquisition" tone back to the mobile unit. When the interrogating mobile detects the acquisition tone, it then transmits its collect and group tones, which the repeater regenerates for all idle mobile units on the system.

The idle mobiles, which continually scan all channels, will stop on the active channel if any of the programmed collect tones are detected and wait for group tone(s).

If the correct tone sequence is detected, the mobiles will alert the operator of an incoming call and open their audio circuits. If the correct sequence is not detected, t he idle mo biles will resume scanning the channels. Once the mobile is "locked" on a channel, it will remain there until the repeater times out or the operator terminates the call.

OPERATIONAL MODES

The radio will always be in one of three operational m odes: idle, wait, or ready. The three operational modes and the conditions that cause the radio to switch from one mod e to another ar e shown in Figure 2.

The radio enters the idle mode when power is turned on and begins scanning channels for incoming calls. The wait mode is entered when the u ser plac es a ca ll. Th e radio r emains i n the w ait mode until a channel is acqui red, or if no cha nnel is avail able. The ready or conversation mode is indicated by an alert tone and the mode indicator on the control panel. A tone signalling Timing Diagram is shown in Figure 3.

Sequence Flow Ch arts for each operational mode are shown in Figures 4, 5, and 6.

Figure 1 - GE MARC V•E Block Diagram

LBI-38952 LBI-38952

IDLE MODE

When the radio is in the Idle Mo de, the audio is muted and all channels programmed for call decode are sequentially scanned for an incoming call. An incoming call is identified by detecting one of the collect tones programm ed in the a rea. Up on receipt of a collect tone, the mobile looks for a short interval for the group or individual tones, providing that their collect tones are the same. Wh en no valid tone is found, the mobile will resume scanning the channels for an i nc om ing c a ll.

If a group (o r in divi dual dec ode ) t on e is de tecte d the mo bile then looks for busy tone f or a 90 millisec ond per iod. If four tones are properly decoded, the mobile wi ll then look for busy t one for 270 milliseconds.

When no valid tones are found, the mobile will resume scanning for a call with the next channel. When a busy tone is found, the mobile will enter the Ready Mode. If busy ton e is not detected, the mobile remains in the Idle Mode and continues scanning channels looking for an incoming call.

Removing the handset from the hanger, pressing the PTT switch or pressing the SEND key on the handset, will caus e the radio to enter the Wait Mode.

WAIT MODE

When the user enters the Wait Mode, the display gro up is checked to make sure it is a valid ca ll-originate g roup. I f it is not valid, a low-frequency tone is heard for one second. If valid, the radio will scan the call-originate frequencies for brief intervals until it finds one with no busy tone on it. If no channel is free, the radio, if programmed for this option, will activate the Call Retry state and display "RETRYING" in the d ispla y. R et rying will cause the radio to revert to the Idle Mode and scan for an incoming call while tr ying to acquire a free repeater approximately every 5 seconds for a 2 minute period. If the Retry option is not enabled, the mobile will sound the low-frequency tone, and then return to the Idle Mode and display "BUSY".

If a channel wit h no busy tone i s foun d, the m obile t ransmits a burst of busy tone to acquire the repeater. The repea ter then responds with a burst of acquisition tone. Upon receipt of the acquisition tone, the mobile proceeds to transmit th e group tones (either two or four tones). If a four-tone sequence is sent, the mobile must detect all four tones and busy tone before entering the Ready Mode. If a two-tone sequ ence is sent, the busy tone must be present within 90 milliseconds of the last tone in order for the radio to enter the R ead y Mo de. If no busy t one is p rese nt, or if the four-tone sequence isn’t valid, the mobile will jump to the next channel in the call or igin ate set an d check f or busy t one as described above.

READY MODE

When an incoming call has been detected, or an idle channel has been acquired, the mobi le enters the Read y mode. In this mode, the audio and Push-To-Talk circuits are enabled, the speaker is unmuted, and the operator is alerted by an alert tone. The radio can then be used in the conventional push-to-talk manner with the radio remaining on the channel until the operator hangs up or the repeater drops the busy tone, causing the unit to revert to Idle mode.

Figure 2 - Operational Modes

Figure 3 - Timing Diagram

If a call is ini tiated and a sequence of five beeps is

sounded, the user cannot access the radio system due to

being out of mobile receive range or being inoperative.

Any subsequent call will be ignored for 20 seconds.

NOTE

Figure 4 - Idle Mode

LBI-38952 LBI-38952

Figure 5 - Wait Mode

Figure 6 - Ready Mode

LBI-38952 LBI-38952

GLOSSARY OF SYSTEM TERMS

Idle Mode

In the "standby" condition, the mobile is inactive, but prepared to call or be called. The trunked radios are IDLE until they are turned off.

Wait Mode

In the "attempting origination" condition, the Wait m ode is entered from Idle mode (only) as the user presses the PTT switch on the handset, or comes "off-hook". If successful, the unit becomes READY. Otherwise, the unit is IDLE or IDLE/WAIT after all chan ne ls ar e t ri ed .

Ready Mode

In the "operating:" condition, Ready is entered from Idle mode via Wait Mode when calling, or dire ctly from Idle when called. Ready Mode ends (the rad io reverts to Idle) wh en the user disconnects or with the loss of received Busy Tone from the repeater. This normally occurs when the repeater shuts down after communication is completed.

Busy Tone

A tone of 3051.9 Hz is the standard busy tone; 2918 Hz is the alternate busy tone. The busy tone modulates mobile and repeater transmitters at a low level of 1 kHz deviation continuously. This tone is filtered out of the received audio and is used to hold the communication channel active. It also excludes other mobiles from using the channel when a call is active.

Acquisition Tone

A 1962.9 Hz tone sent at full deviation for 50 milliseconds from the repeater is used as acknowledgment from the repeater that a busy tone was sent and signals the mobile that signalling tones can now be sent.

Collect Tone

A tone chosen from 34 standardized frequencies, ranging from 508.6 Hz to 2792.4 Hz, i s used as t he first t one in th e group tone sequence. The collect tone is used to gather all mobiles with the same collect tone for decoding a call. The duration of the tone varies as a functio n of the number of chan nels which are pro grammed into the mobile and/or repeater.

In a two-tone call, the m obile sends the collected tone for a programmable duration. In the four-tone call, the m obile always sends a 90-millisecond collect tone, which the repeater regenerates, and sends for the correct duratio n.

Group/Individual Tones

Group/Individual tones chosen from the 34 standard frequencies, follow the collect tone. In a two-tone call, the second tone is sent for 450 m illiseconds. In a four-tone call, the second, third, and fourth tones are sent for 90 milliseconds from the mobile and 180 millise conds from the repeater.

RADIO OPERATION

Refer to Operator’s Manual LBI-38950 provided with each radio for complete oper ating i nstr uc t io ns.

VISUAL INDICATORS

An alphanumeric Liquid Crystal Display (LCD) displays telephone numbers and messages associated with call processing and feature processing. The display has eight alphanumeric characters and other ded ic a te d sta tus i ndica t ors.

ALPHANUMERIC STATUS INDICATORS

Busy

When "BUSY" is displayed, an attempt to place a call has been attempted by the selected GE-MARC system do es not have any available cha nnels. If th e "Call Retry" option has been enabled during radio initialization by the system operator, the radio will retry at 5 second intervals, up to 15 time unless the END key is pressed or a channel is acquired, or an out-of-range condition occurs.

Retrying

When "RETRYING" is displayed, the radio is attempting to establish a channel.

Wait

"WAIT" is displayed when the radio is acquiring a channel

after call origination has begun.

STATUS INDICATORS

No Service

The NO SVC status indicator is displayed when an at-

tempted call cannot be completed because the unit is out of the service area of the selected GE-MARC system.

Roam

The ROAM status indicator is displayed when the mobile

is on channel in the conversation mode.

Function

The FCN status indicator is displayed when the function

key has been pressed so that extended features can be accessed.

In Use

The IN USE status indicator is displayed when the radio

is transmitting in either simplex or duplex modes of operation.

Bar Status Indicator (|||||)

In conventional or direct mode all 5 bars are lit to indicate the presence of a carrier (on chann el RF signal). In trunked mode the bars are used separately as a call counter. Each bar informs the user that an unanswered call has been received (up to 5 total). The display indicates the last received unanswered caller’s area/group name.

Horn

The HORN status indicator indicates the horn alert is active.

Mute

The MUTE status indicator is displayed when the trans- mit audio mute feature is active (duplex mode only).

Lock

The LOCK indicator is displayed when the lock function has been activated. If the unit is locked before it is turned off, then -LOCK- will be displayed when the unit is powered up again.

AUDIBLE INDICATORS

SELF CHECK TEST ALERT

Three beeps are sounded afte r the radio is turned on to indicate that the radio has passed the self diagnostic test. The display will show PASSED for one secon d.

CALL RECEIVED ALERT (Trunked mode only)

A short, high frequency tone is sounded when you r eceive a group call. A two tone alert is sounded when receiving an individual call. NOTE: the radio can be preprogrammed to mute the call received alert tones.

CALL ORIGINATE ALERT (Trunked mode only)

"WAIT" will momentarily be displayed when a call is

being placed. Then a three tone alert is sounded to indicate the call origination is complete. This indicates a channel was acquired and is ready for normal conversation.

SYSTEM BUSY (Trunked mode only)

A low frequency tone is sounded for one second after attempting to place a trunked call and "BUSY" will be di splayed. This indicates that the GE-MARC system is busy a nd you should try again later. If the "Call Retry" option has been enabled during radio initialization by the system operator, the radio will retry a t 5 s ec ond i nte rval s, up to 15 t imes unle ss th e END key is pressed or a channel is acquired, or an out-of-range condition occurs.

OUT OF RANGE ALERT (Trunked mode only)

If the NO SVC status indicator is displayed and five beeps are sounded after attempting to place a trunked call, then the radio is out of range of the GE-MARC s ystem. If the be eps sound when the radio is within known range of the system, the radio may need servicing (even though the self diagnostic test passed at power on).

LBI-38952 LBI-38952

INVALID CALL ORIGINATE ALERT (Trunked mode only)

A low frequency tone is sounded for one secon d immed i-

ately after pressing the handset PTT and the display does not show WAIT. This indicates a call was attempted withi n a group that is not enabled for ca ll ori gin at e.

CARRIER CONTROL TIMER (Trunked and Conventional modes)

A pulsed tone signal is sounded after the handset PTT is pressed continuously for a preprogrammed time in trunked mode. After nine seconds of pulsing the alert tone, the radio unkeys the transmitter and communications are interrupted. While the tone is pulsing, the user can release and press the PTT again to reset the timer and resume the conversation. In conventional mode, the radio unkeys and beeps until the PTT switch is released.

In duplex mode a quick two not alert is heard at the interval of the carrier timer to let the user know that the interval has elapsed (i.e. every 1 minute if CCT = 1.0 minute) and repeated at every time interval.

GE-MARC SYSTEM TONES

The GE-MARC system may give other tones to alert the user of system time-out, etc. Contact your GE-MARC system operator for details about these alert tones.

KEY DEFINITIONS/FUNCTIONS

MISCELLANEOUS KEYS Power

The POWER key is located on the b ackside of the handset. When pressed once the radio performs a self test and will beep three times. The display will momentarily di splay the frequency set and then display the AREA and GROUP currently selected. If an error has been encountered ERROR# will be displayed. (Contact your authorized service represe ntativ e if an error message is displa yed). Press the power b utton agai n to turn the ratio off.

Push-To-Talk

The PTT button is located on the left side of the handset. This key must be held d own to tran smit du ring simp lex oper ation.

Volume Up (VOLUP)

The VOLUP key is located on the lef t side of the handset.

Press VOLUP to increase the volume level.

Volume Down (VOLDN)

The VOLDN key is located just under the VOLUP key

on the side of the handset. Press VOLDN to decrease the volume level.

FUNCTION KEYPAD Send

The SEND key is pressed to initiate a call. When pressed

the number in the display is sent. If no number is display ed the last number dialed is sent.

Clear (CLR)

Press CLR for less than one second to clear the last digit

entered. If CLR is held down longer than o ne second the entir e number is cleared.

End

When the END key is pressed the active call is terminated.

Recall (RCL)

The RCL key is used to re call numbers from memory

locations.

Store (STO)

The STO key is used to store numbers in memory.

Alphabet Keys ( A, B, C)

The A, B, C keys are "Hotkeys" that provide the MDR with

quick dialing for 3 of the most frequently called numbers or emergency numbers.

Function (FCN)

The FCN key activates extended features (used with asso-

ciated secondary keys).

NUMERIC KEYPAD

0 - 9

The 0-9 keys are used to enter telephone numbers and

activate extended features.

Asterisk (❉)

The (❉) key is used to ramp through and select areas. This

function is only active while calls are not in progress. During a call the (❉) key is used to send the Dual Tone Multi-Frequency (DTMF) tone (❉). In dispatch mo de (❉) brings up the dial tone.

Pound (#)

The (#) key is used to ramp through and select groups and channels. This function is only active while calls are not in progress. During a call the (#) key is used to send the DTMF tone for (#). In the telephone interconnect mode (#) e nds the c a ll.

TELEPHONE EXTENDED FEATURES

Extended features are accessed by first pressing the FCN key then one of the following keys.

Key Function Comments

1 (QZ) HORN Enables/disables the horn alert

feature.

2 (ABC) BACKLIGHT Enables/disables the backlight.

FCN/2 turns ON. FCN/2 again, turns OFF.

3 (DEF) OVERDIAL Enables overdial mode for plac-

ing/storing dispatch overdial calls.

4 (GHI) EXTERNAL

SPEAKER

Enables/disables the external speaker in duplex and simplex.

5 (JKL) SIMPLEX Disables duplex, allows simplex

operati on.

6 (MNO) MUTE Enabl es/disable s mi crophone

mute during duplex operation.

7 (PRS) LOCK Enables the LOCK feature. (Pro-

vided a lock code has been preprogrammed.)

8 (TUV) LENGTH Allows DTMF length to be pro-

grammed from keypad (100-450 msecs).

9 (WXY) DELAY Allows delay after DTMF star (❉)

to be programmed from keypad (0-7 secs).

0 (OPER) SPC Selects special call tone set f or

encoding (if programmed).

❉ SYSTEMS Changes t he direct ion of ar ea

ramp. If the area number is known (i.e. 1 - 36) it may be entered in the display, then by pressing star (❉) that area will become the new selected area.

# GROUPS/

CHANNELS

Changes the direction of group/channel ramp. If the group/channel number is known (i.e. 1 - 9) it may be entered in the display then by pressing pound (#) that channel/group will become the new selected channel/group.

A TESTMODE Allows testmode to be entered

(unless disable d from pre-pro-

gramming). B UNUSED C TALK TIME Displays call timer (active if call

is in progress, last call length if

call is not in progress). VOLUP VOLUME UP Sets the volume at the max set-

ting. [VOL = 15]. VOLDN VOLUME

DOWN

Sets the volume at the min setting.

[VOL = 00].

When VOLUP or VOLDN button is depressed the volume is momentarily displayed in the Alphanumeric display (ex., VOL= 15). VOL 15 is the maximum volume level. After the radio has been turned off the last volume level is retained and is the default volume level after the radio is powered on.

NOTE

LBI-38952 LBI-38952

BASIC OPERATION

The radio is powered on by depressing the green power key located on the bottom of the handset. A self diagnostic test is performed when the radio is first t urned on. When tes ting is complete the Area and Group informati on is displayed on the handset alphanumeric display. If an error was detected during self test diagnostics the message ERROR# will be displayed. The following table summarizes the possible diagnostic test exceptions.

PC PROG No personality. The radio has not been

PC programmed with the customer in-

formation. ERROR2 Not Used. UNLOCK The synthesizer is unlocked. The syn-

thesizer was tested and failed to lock in

the proper amount of time at various

frequencies across the band. PROM Bad The EPROM program memory check-

sum test has encountered an error. The

EPROM has been corrupted or is mal-

functioning.

VOLUME ADJUSTMENT

The user may adjust the volume at any time using the

VOLDN and VOLUP buttons located on the side of the handset. If the volume is adjusted while a call is in progress, no audible beeps will be heard; however, a momentary visual reminder of the volume setting will be displayed. (e.g. [VOL = 07]). If there is no call in progress, a short beep will be heard, in addition to the visual indication. A f te r one second the volume message will be replaced by the selec ted ar ea and g roup na me. In a ddition t he user selected volume off-hook is saved separately from the user selected volume on-hook.

AREA SELECTION

The desired AREA can be s elected by pressing a nd releasing

the (❉) key. This will increment the displayed area to the next AREA available. The user may also depress the FCN key and then the (❉) key to reverse the direction of the AREA selection. The area may also be en tered directly b y entering the d esired area number and then pressing the (❉) key.

GROUP SELECTION

The desired group is select ed by pressing and releasing the

(#) key. The direction of ramming can be changed by pressing the FCN key and then pressing the (#) key. The group may also

be entered directly by entering the desired group number and then pressing the (#) key.

CHANNEL ACTIVITY

To provide quick access to the communications channels,

the GE-MARC V/V•E trunked radio system continually monitors the activity on all the system channel s. When a call is initiated, the tru nked ra dio a utom ati cally see ks a non busy c hannel. Once communicatio ns have been es tablishe d, if a channel has not been active for six seconds or more t he channel is disconnected; i.e. communications ar e interrupted. If this occ urs before the conversation is complete, the call must be reinitiated.

To avoid confusion it is recommended that a procedure be set up so that the originator of the call is the one designated to re-establish communications.

PLACING A DISPATCH CALL

1. The user must first select desired AREA and GROUP.

2. The user can place a dispatch call by pressing the PTT switch located on the side of t he handset (or remove the handset from its holder when the pre-programmed option has been enabled).

3. The display will change from the selected area and group to [WA IT] while the radio is acquiring a repeater.

4. The radio sounds a three-tone alert signal when you can begin the conversation.

5. If the radio is out of the range of the selected system, 4 short and 1 long beep will be heard and NO SVC status indicator will be displayed for approximately 20 seconds. While NO SVC status indicator is displayed, no attempts can be made to place a call. If a new area is selected the NO SVC indicator goes out and the call can now be attempted in the new service area. If all available repeaters are busy when the call is attempted, the user will hear 1 long beep is heard and [BUSY] will appear in the display.

If the call retry option was enabled during PC programming, [RETRYING] will appear in the display instead of [BUSY].

6. The selected area and group will be displayed again once the call is completed.

PLACING AN INTERCONNECT OR DISPATCH OVERDIAL CALL

There are four methods to place an interconnect or dis-

patch overdial call.

1. The user must first press FCN 3. [OVERDIAL] will be displayed. the user must then manually dial the dispatch ID (2 or 4 tone sequence for example [-1809] or [18092310]). The sequence will be preceded b y the overdial prompt [-]. Then press the SND key.

2. The SND key can be pressed which will automatically redial the last phone number or dispatch ID.

3. The user can recall previously stored dispatch ID’s and phone numbers from memory and then press SND.

4. The user can remove the handset from its holder (preprogrammed option). If a dispatch or telephone number was not entered, prior to removing the handset from the holder, the radio will acquire a channel. After the channel has been acquired recall or enter the desired number and press the SND key. If entering a dispatch number takes more than 5 seconds depress the PTT switch periodically to keep the channel active while the ID sequence is entered.

ENDING A CALL

The call can be ended three ways:

1. Pressing the END key.

2. A system disconnect or time-out occurs. During a dispatch call the time-out occurs after 6 seconds of channel silence. During an interconnect call the time-out occurs after 30 seconds of channel silence.

3. Returning the handset to the holder (a pre-programmed option).

RECEIVING A CALL

When a call is received by the radio, the radio decodes the

call. A single alert tone will sound indicating a GROUP call has been received or a two-tone alert will sound if an INDI- VIDUAL call has been received. The display will show the user the AREA and GROUP, when receiving a group call,

and the AREA and INDIVIDUAL d ecode when an INDIVID- UAL call is received.

If a simplex dispatch call is desired, simply pick up the

handset and use the PTT switch to t ransmit t o the c aller. If the call is an interconnect call, press the star (❉) to answer the call and place the unit in duplex.

Duplex operation must be enabled during PC programming for the tone set being used during duplex mode. If Auto-interconnect is enabled for the area and the Individual tone set being decoded, the user may enter duplex by removing the handset from the cradle. If the handset has al ready been removed from the cradle when the call is recei ved, the user must press the (❉) to go into duplex.

DIRECT MODE OPERATION

The Direct mode provides short range, line of sight communications for radios having the talk-around option installed. In the Direct (or talk -around) mode, t he radio is not operati onal in the GE-MARC system.

1. Using the (❉) key select the direct mode area. The Group

key (#) has no effect in the direct mode frequency set.

2. Before making a call, determine if the channel is in use.

Press CLR key to momentarily disable the squelch to

monitor the channel. Also, removing the handset from

the holder allows you to monitor the channel without

disabling the squelch (Busy Tone is disabled). The status

indicator (|||||) in the display will also show if the channel

is in use.

3. Press PTT switch and send your message.

CONVENTIONAL MODE OPERATION

1. Using the (❉) key select the conventional mode area. If

more than one channel is available in the conventional

system, press (#) key to select the channel ( up to 9

channels may be available in one conventional area).

2. Before making a call, determine if the channel is busy

by pressing the CLR key momentarily to disable the

squelch and monitor the channel for activity. Also re-

moving the handset from the holder allows you to moni-

tor the channel without disabling the squelch (Channel

Guard is disabled). The ||||| status indicator in the display

will be active if the channel is in use.

3. Press the PTT switch and send your message.

If you plan on a lengthy call (or several calls), the vehicle engine should be running to maintain battery charge.

As each key is pressed on the keypad, the display should be observed before proceeding to the next key . Pressing keys too rapidly in succession could result in incomplete or incorrect calls.

NOTE

LBI-38952 LBI-38952

Call Timer

The call timer displays the length of the time the conver-

sation in progress, or most recent call, has taken. To display the call timer, during a conversation, press the FCN key and then press the C Hotkey. The timer will be displayed and will be operational. The call timer may be viewed after a call has been completed by pressing the FCN key and then pressing the C key. The timer can be remove d from the display by pressing the CLR key.

Last Digit Clear And Display Clear

To clear the last digit entered in th e display, m ome ntarily

depress the CLR key. To clear the entire d isplay , d epress th e

CLR and hold for one second.

Storing Numbers

The number of dial locations available to the user is pre-programmed by the system operator. The user may chose 10, 20, 30, 40 o r 5 0 lo cations. T he m ax imum nu mber of di gits stored in any location is 15. The user can store phone numbers dispatch IDs by following these steps:

1. The u ser must first key in the telephone number, or dispatch overdial tone sequence, from the keypad.

2. The user must then press the STO key.

3. ADR xx will be displayed where xx is the next available storage address.

4. If the suggested memory location is OK, then press the STO key. This will store the number and return the radio to normal operation.

5. If the displayed address is not acceptable, key in the memory location (1-50, depending on the number of locations enabled by pre-programming). The A, B or C

HOTKEYS are also valid memory locations.

Recalling Numbers

The user can recall numbers previously stored by follow-

ing these steps:

1. The user must first press the RCL key.

2. The memory locatio n of the desired number is then keyed in (1-50, depending on the number of locations enabled during PC programming or HOTKEY A, B or C). The dispatch or phone number will be displayed. If the number is gr eater than 8 digits long t hen the first 8 digits will be displayed for o ne sec ond and then the last eight digits will be displayed and remain in the display. If a location d oes not h ave a nything in it, [ EMPTY ] will be displayed.

Hotkeys

Pressing A, B or C will automatically recall and dial the

number stored at that location without further user intervention.

Last Number Redial

The user can press the SEND key with an empty display

and the radio will dial the l ast dialed number. By pressing the RCL key twice, the user can display the last number dialed. After displaying the number, the user can redial by pressing the SEND key.

Locking The MDR Mobile Radio

The user may choose to lock the radio b y pressing the FCN

key and then the 7 (PRS). The LOCK status indicator will be displayed. If the unit is turned off and then on again while it is locked, [- - LOCK - -] will be displayed. In this mode no calls can be originated or received. This feature is disabled if a lock code is not entered during initial programmin g by the system operator. Lock codes can be 1 to 7 digits long. The lock feature is operational only when a call is not in progress.

Unlocking The Mobile

After the mobile has been locked the user may unlock the mobile by keying in the lock code. If an inco rrect digit is e ntered simply start over with the correct code.

Backlight

The backlight functio n can be toggled ON or OFF by pressing FCN key and then the 2 (ABC) key.

Horn

If your radio has th e horn alert option; it can be enabled or disabled by pressing FCN key and then p ress ing the 1 (QZ) key.

External Speaker

To enable the external spe aker, p ress t he FCN key and then the 4 (GHI) key. Toggling this function provides the user with the capability to have private conversations or allow other passengers in the vehicle to hear the conversation. After power on the external speaker is enabled while in conventional mode and disabled during trunked mode.

Call Hold (Mute)

The user can Enable or Disable the microphone, so that the called party cannot hear your conversation, by pressing the FCN key and then the 6 (MNO) key. This feature is only available in duplex operation.

Simplex Operation

The user can choose to terminate duplex operation and still maintain the interconnect call in progress by pressing FCN key then pressing the 5 (JKL) key. This returns the radio to the simplex mode of operatio n. To return to duple x, the user can press the star (❉) key.

DTMF Digit Length

The user can change the duration of the DTMF tones by

pressing the FCN key then the 8 (TUV) key. The proper [LENGTH?] is displayed and the radio waits for the user to enter a value between 2 and 9. If an out of range value is entered the radio will display the correct range i.e. [RNG = 2-9]. The user can then enter the desired value. The numbers entered represent 50 millisecond inte rv als ( i. e. 100 - 4 50 m s ec ) .

Delay After DTMF Star (❉)

The user can also cha nge t he durat ion of th e D TMF st ar (❉)

tone. This value can be changed by pressing the FNC key and then the 9 (WXY) key. The prompt [DELAY?] is returned and the radio waits for the user to enter the desired value between 0 and 7 milliseconds. If an out of range value is entered the radio will display the correct range i.e. [RNG = 0-7]. The user can then enter the desired value.

TABLE 1 - CHANNEL GUARD TONE FREQUENCIE S

Standard Tone Frequencies Hz

67.0 97.4 136.5 192.8

71.9 100.0 141.3 203.5

74.4 103.5 146.2 210.7

77.0 107.2 151.4

79.7 110.9 156.7

82.5 114.8 162.2

85.4 118.8 167.9

88.5 123.0 173.8

91.5 127.3 179.9

94.8 131.8 186.2

When specifying repertoire locations, using either RCL or STO, the user need not enter the 0 preceding locations 1 through 9 (i.e. RCL 3). However, if the entire number is specified, the action will be taken immediately. If the user presses just the last digit then the action will not be taken for one second. This allows the user time to enter the second digit (i.e. RCL 3 2).

NOTE

If a number already exists in the memory location entered then the new number will replace it. If all locations have something programmed in them the prompt [ FULL ] will be displayed.

NOTE

There are 3 HOTKEYS (A, B and C) available for storing your most frequently called numbers. When used to initiate a call these locations are recalled and dialed simply by pressing the HOTKEY. RCL is not required.

NOTE

To reverse the polarity of the digital Channel Guard codes, in the PC programmer, type I (i) ("inverted") before the code number, i.e. I023.

NOTE

LBI-38952 LBI-38952

PARTS LIST

TABLE 2 - DIGITAL CHANNEL GUARD CODES

PRIM. CODE

EQUIV.

CODE

PRIM. CODE

EQUIV.

CODE

PRIM. CODE

EQUIV. CODE

023 340,766 142 174,270 266 655 025 143 333 271 427 ,510,762 026 566 144 466,666 274 652 031 374,643 145 525 276 326,432 032 147 303,306,761 307 362,565 036 137 150 256,703 311 330,456,561 037 560,627 043 355 152 366,415 312 515,663,743 047 375,707 153 606,630 315 321,673 051 520,771 155 233,660 317 546,614,751 053 156 517,741 324 343,570 054 405,675 157 322,503 325 550,626 056 465,656 161 345,532 331 372,507 057 172 060 116,737 162 416,553 332 443,552 065 301 163 460,607,654 344 471,664,715 066 734 164 207,732 346 616,635,724 067 516,720 165 354 351 353,435 071 603,717,746 171 265,426 356 521

072 470,701 363

436,443,444 662

073 640 212 253 446 467,511,672

074 360,721 213 263, 736 447

473,474,731

744 075 501,624 217 371,453,530 452 524,765 076 203,754 222 445,457,575 454 513,545,564 104 226,557 223 350,475,750 455 533,551 107 365 224 313,506,574 462 472,623,725 114 327,615 225 536 523 647,726 115 534,674 227 261,567 526 562,645 117 411,756 231 504, 631,636, 745 122 535 234 423,563,621 713 123 632,657 235 611, 671,723 125 173 236 251,704,742 127 412,441,711 237 464,642,772 130 364,641 243 267, 342 131 572,702 245 370, 554 132 605,634,714 246 542,653 133 413,620 252 6 61 134 273 254 314,612,706 135 205,610 255 4 25 136 502,712 262 316, 431,730

SYMBOL PART NUMBER DESCRIPTION

— — — — ASSEMBLIES — — —

A1 19D902172G2 LOGIC BOARD A2 19D902123G20 RF BOARD A3 19D902188G3 AUDIO BOARD A4 19D903504G2 DUPLEX INTERFACE BOARD A5 19D901891G3 SYSTEM BOARD A9 19D904025G1 AUDIO AMPLIFIER BOARD

344A3783P2 HANDSET

— — — — — — KITS— — — — —

344A4253G1 Hardware Kit (No. 1) 344A4255G7 Hardware Kit (No. 2)

— — — — — CABLES — — — —

19A705301P7 Cable, Antenna 19B801467P1 Cable, J705 to J151 19B801467P2 Cable, J5 to J105 19B801454P36 Cable, RX to J104 19A705235P3 Cable, Ribbon, J901 on audio amplifier

board to J902 on system board 19B801454P38 Cable, Antenna to J7 19B801454P37 Cable, TX to J101 19B802397P1 Cable, Handset

— — — MISCELLANEOUS — —

19D904027P1 Casting 19C337682G2 Bracket 19D904185G1 Cover, Bottom 19D904186G1 Cover, Top 19B801362P3 Duplexer, 806-870 MHz 19D904187G1 Panel, Front 19A705606P2 Handset Holder, Positive Latch 19B801358P18 Cable, 9 Foot, Power 19B235310P10 Nameplate, Combination 344A3796G5 PROM Kit

COMPONENTS, ADDED, DELETED OR CHANGED BY PRODUCTION CHANGES

MDR MOBILE RADIO ASSEMBLY

LBI-38952 LBI-38952