Epson S020193 User Manual

EPSON

Product Information Sheet

1. Article and Corporate Identificat ion

Product: Epson Ink Cartridge S020193

for use with Epson Stylus Photo 750 Printer

Manufacturer/Distributor: Epson America, Inc.

3840 Kilroy Airport Way
Long Beach, CA 90806
United States
TEL: [phone]
FAX: [phone]

The EPSON S020193 Ink Cartridge

Medical Emergency Number: [phone] Epson Quick-Dry ink is engineered to

provide superior Photo Quality results.

2. Composition Information

This is an aqueous ink formulation

Ink Composition CAS No. % By Weight

Proprietary dyes and pigments - < 3 %

Diethylene glycol 111-46-6 < 10 %

Proprietary organic materials - 15 – 20 %

Glycerols - 10 - 15 %

Water 7732-18-5 balance

3. Hazard Identification

3.1 Emergency Overview: Ink component is a three part light yellow, magenta, and cyan liquid that may cause eye

irritation. Avoid contact with eyes or clothing. In the case of skin contact, wash with soap
and water. Keep out of reach of children.

3.2 Potential Health Effects:

Eyes: Ink contact with eye may be mildly irritating. See Section 11 for Toxicology.

Skin: Ink contact with skin may cause irritation, swelling, or redness. It is not expected to cause an allergic

skin reaction. See Section 11 for Toxicology.

Inhalation: Intentional exposure to ink vapors may cause respiratory irritation. See Section 11 for Toxicology.

Ingestion: May cause upset stomach. See Section 11 for Toxicology.

PIS # S020193 Version 3.20 (USA)
Page 1 of 4 Release Date 10/15/00

EPSON

4. First Aid Measures

4.1 Eyes: Immediately flush with room temperature, low pressure, clean water for at least 15 minutes. Seek

medical attention if eye irritation continues.

4.2 Skin: Wash surface areas with soap and water. Wash soiled clothing before rewearing. Consult a physician

if irritation continues.

4.3 Inhalation: Remove subject to ventilated fresh air. Consult physician if necessary.

4.4 Ingestion: Seek medical advise; and attention if stomach continues to be upset.

5. Fire Fighting Measures

5.1 Flammability: Flash point is greater than 230 deg. F / 110 deg. C (closed cup in accordance with

ASTM D3278)

5.2 Extinguishing Media: Dry chemical or carbon dioxide

5.3 Fire Fighting Instructions: No special fire fighting procedures are required other than breathing apparatus. No

special explosion hazards are known.

6. Accidental Release Measures

If a spill occurs, use sponges to wipe-up ink, then rinse area with damp cloth. Place waste in closed container for
disposal. Use proper ventilation. Do not dispose of waste to the sewer. No eye or skin protection required during
clean-up. Wash hands with soap and water.

7. Precautions for Safe Handling and Use

Keep out of reach of children and do not drink ink. Do not store the cartridge in high or freezing temperatures. Keep
cartridge out of direct sunlight. Do not dismantle cartridge. Do not store cartridges with oxidizing agents or
explosives. Make sure cartridge is dry before insertion into printer housing.

8. Exposure Controls and Personal Protection

8.1 Engineering Controls: None required

8.2 Exposure Controls: None required

8.3 Personal Protection: None required when cartridges are used as intended

9. Physical and Chemical Properties of Ink Formulation

Appearance: Yellow, Magenta, and Cyan Liquid
Odor: None
pH: 9 - 10
Boiling point: Approximately 212 deg. F / 100 deg. C
Freezing point: Less than 32 deg. F / 0 deg. C
Melting point: Less than 32 deg. F / 0 deg. C
Flash point: Greater than 230 deg. F / 110 deg. C (closed cup, ASTM D3278)
Autoflammability: None

PIS # S020193 Version 3.20 (USA)
Page 2 of 4 Release Date 10/15/00