Epson PowerLite Pro Cinema 1080 User Manual

PowerLite® Pro Cinema 1080

Home Theater Projector

User’s Guide

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson is a registered trademark, and Epson Exceed Your Vision, Crystal Fine, and 1080Perfect are trademarks of Seiko Epson Corporation.

PowerLite and PrivateLine are registered trademarks, AccuCinema is a trademark, and Extra Care and Epson Connection are service marks of Epson America, Inc.

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

The contents of this manual are subject to change without notice.

CPD-22934R1

Introduction 7

Projector Parts 8

Front 8 Back 8 Bottom 9

Projector Control Panel 9 Remote Control Button Map 10 Optional Accessories 11 Registration and Warranty 11 Using This Manual 12

Setting Up the Projector 13

Choosing a Location 13 Installing the Projector 16 Connecting the Cables 18

Connecting Video and Computer Equipment 18

Making Other Connections 20 Installing Batteries in the Remote Control 21 Turning the Projector On and Off 22

Turning On the Projector 22

Turning Off the Projector 23 Selecting the Image Source 23 Positioning the Image 25

Making Basic Adjustments 27

Focusing and Zooming 27 Choosing the Aspect Ratio 28 Choosing the Color Mode 29

Contents 3

Adjusting Color Temperature, Skin Tone, and Gamma 30

Adjusting the Gamma Setting 31 Locking the Projector 32

Making Detailed Adjustments 33

Using the Menu System 33

Changing How the Menus Display 35 Adjusting the Picture Quality 35

Input Brightness Settings 35

Sharpness and Picture Quality Settings 37

Color Settings 38

Adjustments for Computer Images 40 Selecting Memory Settings and Resetting the Projector 41

Selecting Memory Settings 41

Creating Memory Settings 41

Deleting Saved Memory Settings 42

Resetting the Projector 42 Customizing Projector Features 43

Image Sizing 43

Screen Options 44

Other Setup Options 44

Maintenance 47

Cleaning the Lens 47 Cleaning the Projector Case 48 Cleaning and Replacing the Air Filter 48 Replacing the Lamp 50

Checking the Projector Status 53 Storing the Projector 53 Transporting the Projector 54

4 Contents

Resetting the Lamp Usage Timer 52

Problem Solving 55

What To Do When the Lights Come On or Flash 55 Solving Picture Problems 56 Solving Remote Control Problems 59 Where To Get Help 60

Specifications 61

General 61 Lamp 61 Remote Control 61 Dimensions 62 Electrical 62 Environmental 62 Safety 62 Compatible Video Formats 63 ESC/VP21 Command Codes 65

Notices 67

Important Safety Information 67 FCC Compliance Statement 69 Declaration of Conformity 70 Epson America, Inc. Limited Warranty 71

Index 73

Contents 5

6 Contents

Introduction

The PowerLite® Pro Cinema 1080 projector lets you enjoy theater-quality images in the relaxing environment of your own home. Designed especially for home cinema use, it offers these outstanding features:

■ Native 1080p (1920 × 1080) resolution, 12000:1 dynamic contrast ratio, and up to 1200

lumens for incredibly rich, sharp images in any room lighting

■ Auto Iris system that constantly controls the lamp intensity based on the gamma and

black/white levels of your projected content, for perfectly adjusted images and Deepest

™

Blacks

■ Epson

■ 1080Perfect

■ 10-bit color quality for unmatched color accuracy, with over a billion colors available

■ Epson AccuCinema

■ HDMI

Crystal Fine™ 3LCD technology for reliable picture quality, increased contrast

ratio and uniform colors

™

video processing for more film-like images free of noise or artifacts

™

color management delivered by the built-in optical Cinema Filter blocks out excess light for an expanded, purer color range and sophisticated grayscale tracking

™

(High Definition Multimedia Interface™) port for superior, uncompressed

digital video

■ True 16:9 wide-format projection

■ Flexible setup configurations, including front projection and ceiling mounted, with

vertical and horizontal offset lens shift

■ Six color modes to quickly optimize viewing for different lighting environments and a

vast array of custom color adjustments

Introduction 7

Projector Parts

Front

Control panel

Horizontal lens shift dial

Vertical lens shift dial

Zoom ring

Focus ring

Ventilation slots

Adjustable foot

Infrared receiver

Lens cover

Back

D/SCART port (used mainly in Japan)

Trigger out port

Video port

S-Video port Control (RS-232C) port

Component video ports

AC power inlet

PC port

Main power switch

HDMI port

Infrared receiver

Kensington lock port

8 Introduction

Bottom

Mounting bracket connections

Lamp cover Air filter

Projector Control Panel

Power light

Power button

Warning light

Source button Switches the video input source

Menu button Displays the menus

Menu navigation buttons

Esc button Exits the current menu item

Aspect button Changes the picture’s aspect ratio

Select button Selects menu items or opens the line menu

Introduction 9

Remote Control Button Map

Operation light Lights when you send remote control commands

Memory button Recalls custom picture settings

Menu button Displays the projector’s menus

Menu navigation buttons

Component button

Gamma button Adjusts the gamma values of the screen display

ColorTemp. button Changes the color temperature of the screen display

Pattern button Displays test patterns to adjust the image

On and Off buttons

Color Mode button Optimizes viewing for different lighting environments

Aspect button Changes the picture’s aspect ratio

Select/Line menu Selects menu items or opens the line menu

ESC button Exits the current menu item

Source buttons Switch between equipment connected to the projector

Contrast button Changes the contrast of the screen display

S. Tone button Adjusts the skin tones of people appearing in the screen display

Blank button Turns off the screen image

Illumination button Lights the remote control buttons for easy viewing

10 Introduction

Optional Accessories

Epson provides the following optional accessories for the projector:

Product Part number

Replacement lamp V13H010L39 (ELPLP39)

Air filter replacement V13H134A09 (ELPAF09)

Projector mount ELPHB800

Kensington security lock (anti-theft device) ELPSL01

You can purchase accessories from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

Registration and Warranty

The PowerLite Pro Cinema 1080 comes with a basic three-year carry-in warranty. For details, see page 71.

In addition, for customers who register their projector, Epson offers free Extra Care Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See your Extra Care Home Service brochure for details.

Home

To register, simply fill out the registration card that came with your projector and mail it to Epson. Or you can register online at www.epson.com/webreg. Registering also lets you receive special updates on new accessories, products, and service.

Introduction 11

Using This Manual

This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information.

Please follow these guidelines as you read through the manual:

Warning: Must be followed carefully to avoid bodily injury.

Caution: Must be observed to avoid damage to your equipment.

Note: Contains important information about your projector.

Tip: Contains helpful projection tips.

Need additional help? Take advantage of Epson’s automated support services 24 hours a day at epson.com/support. Use this site to view FAQs (Frequently Asked Questions) or product information and e-mail your questions to Epson support.

If you need more help, you can use the Epson PrivateLine (800) 637-7661 and enter the PIN on the PrivateLine support card that came with your projector.

Support service. Call

12 Introduction

Setting Up the Projector

Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image.

Choosing a Location

You can install the projector for various viewing setups, as shown below.

Center

Side

Ceiling

Setting Up the Projector 13

Ideally, place the projector at a height where its lens is between the top and bottom of the screen. That way, you can keep the projector level and use the vertical lens shift dial to position the image. This produces the best-looking picture.

Try to be as close as possible to the calculated projector position when installing the projector. Too much lens shift can cause minor reduction in image dimensions. The image display position cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the horizontal width of the screen.

If you place the projector off to the side, aim it straight ahead (rather than at the center of the screen), then use the horizontal lens shift dial to center the image on the screen.

Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position.

14 Setting Up the Projector

Vertical lens shift dialHorizontal lens shift dial

The maximum size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may be smaller. Use this table as a rough guide for projector placement:

16:9 aspect ratio

Maximum diagonal image

Projection distance

2.8 to 6.2 feet 30 in. (26 × 15 in.) 6.8 to –6.8 in. 0 to 13 in.

3.8 to 8.3 feet 40 in. (35 × 20 in.) 9.1 to –9.1 in. 0 to 17 in.

5.8 to 12.5 feet 60 in. (51 × 28 in.) 13.6 to –13.6 in. 0 to 26 in.

7.8 to 16.7 feet 80 in. (71 × 39 in.) 18.2 to –18.2 in. 0 to 35 in.

9.8 to 20.9 feet 100 in. (87 × 47 in.) 22.7 to –22.7 in. 0 to 44 in.

11.8 to 25.1 feet 120 in. (106 × 59 in.) 27.2 to –27.2 in. 0 to 52 in.

14.7 to 31.4 feet 150 in. (130 × 75 in.) 34 to –34 in. 0 to 65 in.

Projection distance

3.5 to 7.6 feet 30 in. (24 × 18 in.) 8.3 to –8.3 in. 0 to 16 in.

4.7 to 10.1 feet 40 in. (32 × 24 in.) 11.1 to –11.1 in. 0 to 21 in.

size (width × height) Offset A to Offset B

4:3 aspect ratio

Maximum diagonal image size (width × height) Offset A to Offset B

Horizontal Offset

7.1 to 15.3 feet 60 in. (47 × 35 in.) 16.7 to –16.7 in. 0 to 32 in.

9.6 to 20.4 feet 80 in. (63 × 47 in.) 22.2 to –22.2 in. 0 to 43 in.

12 to 25.5 feet 100 in. (79 × 59 in.) 27.8 to –27.8 in. 0 to 53 in.

14.4 to 30.7 feet 120 in. (94 × 71 in.) 33.3 to –33.3 in. 0 to 64 in.

18 to 38.4 feet 150 in. (118 × 91 in.) 41.7 to –41.7 in. 0 to 80 in.

To determine the exact image size when you know the projection distance (or the exact projection distance when you know the desired image size), you can use the Projection Distance Calculator. You can download this program from the Epson website at epson.com/support.

Setting Up the Projector 15

Also keep these considerations in mind:

■ Make sure there is plenty of space for ventilation around and under the projector. Do not

set the projector on top of loose materials that could block the vents underneath.

■ Make sure the projector is within 9.8 feet of a grounded electrical outlet or extension

cord.

Installing the Projector

To install the projector, you first need to determine the location, based on the size of your screen (maximum diagonal image size). Use the table on page 15 as a guide to positioning the projector. Note the following dimensions:

■ Distance from the center of the lens to the mounting bracket holes: 2.60 inches (66 mm),

0.35 inch (8.8 mm) maximum vertical lens shift

■ Distance from the center of the lens to the center of the projector: 4.33 inches (110 mm),

0.30 inch (7.7 mm) maximum horizontal lens shift

16 Setting Up the Projector

The following illustrations show the dimensions of the projector:

5.18 in.

2.60 in.

4.33 in.

15.98 in.

4.88 in.

0.75 in.

5.63 in.

11.81 in.

12.20 in.

2.08 in.

3.04 in.

6.30 in.

To install, you will need the optional projector mount designed for the projector. See page 11 for ordering information.

Warning: When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use any type of oil or lubricant. These may cause the projector casing to crack and the projector may fall, causing serious injury and serious damage to the projector.

Follow the instructions included with the mount to install the projector, which weighs

12.3 pounds. The wall or ceiling where you install it must be capable of supporting a weight of 85.6 pounds.

Setting Up the Projector 17

In addition to the tools supplied with the projector mount, you will need a Phillips head screwdriver and a drill to use on the wall or ceiling.

If you install the projector on the ceiling, you will need to invert the picture so that it appears right side up. Follow these steps:

1. Press the

Menu button on the remote control.

Menu button

2. Press the menu navigation buttons to open the

Settings menu, then select Projection.

3. Use the navigation buttons to select

4. Press the

Menu button when done.

Front/Ceiling.

Menu navigation buttons

If you are planning to use an AV controller with the projector, refer to the table of ESC/VP21 command codes on page 65.

Connecting the Cables

Connecting Video and Computer Equipment

You can connect the projector to any type of video equipment, such as a VCR, DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple

18 Setting Up the Projector

Macintosh® system.

You can connect up to five pieces of video equipment at the same time, using any of the commercially available cables shown below:

Port name Video equipment connection* Computer connection*

HDMI Use an HDMI cable:

Component Use a component video cable

(with RCA-style connectors):

Component video ports

PC — Use a Mini D-sub, 15-pin monitor cable

RGB port

S-Video Use an S-video cable: —

Video Use an RCA video cable: —

* For details on compatible video formats, see page 63.

Connect the cable to the three component video ports. Match corresponding colors between the cable and the ports.

—

to connect to a computer RGB (monitor) port:

Setting Up the Projector 19

For best results, connect your video equipment to the HDMI (High-Definition Multimedia Interface) port, if possible. If your equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): Component (for component video), S-Video, or Video (for composite video).

Connect video equipment to one of these ports

Connect a computer to one of these ports

If you connect to the Component port, be sure to select the correct Input Signal setting for your equipment, or the image may not display properly (see page 23).

Making Other Connections

Connect the power cable and other cables described below, depending on how you plan to use the projector.

■ Plug the power cable into the projector and a grounded electrical outlet.

20 Setting Up the Projector

■ The Trigger out port outputs a 12-volt DC signal

when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use.

Connect a 3.5-mm mini jack to the port, as shown.

Installing Batteries in the Remote Control

The remote control uses two AA batteries.

Warning: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately.

1. Release the tab and lift open the cover.

2. Insert two new AA batteries as shown.

3. Insert the tab on the cover and press it down until it clicks into place.

Aim the remote control at the front or back of the projector. Make sure you are within 30 feet of the projector with the remote aimed within a 30° angle from the infrared receivers.

If you suspect the batteries are weak, take the remote control to a dark room and press the illumination button. If the buttons do not glow red, replace the batteries.

Setting Up the Projector 21

Turning the Projector On and Off

Turning On the Projector

1. Remove the lens cap.

2. Turn on any connected equipment you plan to use.

3. Turn on the main power switch on the back of the projector.

Power switch

4. Press the

Note: To prevent children from turning on the projector, you can use the Child Lock. See page 32 for details.

If you’ll be using the projector at an altitude above 4900 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure. See page 45 for details.

On button on the remote control or the PPower button on the projector.

The projector takes about 30 seconds to warm up and display an image. If you don’t see a picture, you may need to change the image source as described on page 23.

22 Setting Up the Projector

Turn on the projector

Turning Off the Projector

1. Turn off any equipment connected to the projector.

2. Press the

Off button on the remote control, or press the P Power button on the

projector twice.

3. When the P

Power light stops flashing orange and stays on, turn off the projector’s main

power switch on the back.

It is now safe to unplug the projector, if necessary.

Caution: Turn off this product when not in use to prolong the life of the projector. Continuous 24-hour-a-day use may reduce the overall life of the product. Never turn off the main power switch without first turning off the lamp and letting it cool as described above, or you could damage it and reduce lamp life.

Selecting the Image Source

The Source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a DVD player, cable or satellite box, or video game console).

Press the corresponds to the port to which your video source is connected.

Source button on the remote control that

Source buttons

Setting Up the Projector 23

+ 53 hidden pages