Introduction to Your Projector ................................................................................................................... 9
Setting Up the Projector ........................................................................................................................... 21
Refer to these sections to learn more about your projector and this manual.
Projector Features
Projector Part Locations
Projector Features
The PowerLite Home Cinema 707 projector includes these special features:
Bright, high-resolution projection system
• Up to 2700 lumens of brightness (white light output and color light output)
• 720p native resolution
Flexible connectivity
• HDMI port for computer or video device connection
• Component-to-VGA adapter cable included for quick component video connections to a component
video cable
• Plug-and-play 3-in-1 USB projection, audio, and mouse control for instant setup
• PC Free photo slide shows via connected USB memory devices
Easy-to-use setup and operation features
• Horizontal keystone correction slider for flexible projector placement
• Built-in closed captioning decoder
• 1.2× optical zoom ratio for improved zooming capability
• Low total cost of ownership with longer lamp life
• Epson's Instant Off and Direct Power On features for quick setup and shut down
Product Box Contents
Additional Components
Optional Equipment and Replacement Parts
Warranty and Registration Information
Notations Used in the Documentation
Where to Go for Additional Information
Parent topic: Introduction to Your Projector
9
Related concepts
Projector Part Locations
Product Box Contents
Save all the packaging in case you need to ship the projector. Always use the original packaging (or
equivalent) when shipping.
Make sure your projector box included all of these parts:
1Projector
2Remote control
3Remote control batteries (two AA alkaline)
4Power cord
5Component-to-VGA adapter cable
10
6Carrying case
7Projector documentation CD
Parent topic: Projector Features
Additional Components
Depending on how you plan to use the projector, you may need to obtain the following additional
components:
• To receive an S-Video signal, you need an S-Video cable compatible with your device. See your local
computer or electronics dealer for purchase information.
• To receive an HDMI signal, you need a compatible HDMI cable. See your local computer or
electronics dealer for purchase information.
Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you
need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for
compatible adapter options. Older Mac computers (2009 and earlier) may not support audio through
the HDMI port.
• To project with audio from certain ports, you may need a commercially available audio cable
compatible with your device. See your local computer or electronics dealer for purchase information.
Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need
to obtain an adapter that allows you to connect to the projector's VGA video port. Contact Apple for
compatible adapter options.
Parent topic: Projector Features
Optional Equipment and Replacement Parts
You can purchase screens, other optional accessories, and replacement parts from an EPSON
authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can
purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Epson offers the following optional accessories and replacement parts for your projector:
Air filter replacement set (2 filters; ELPAF32)V13H134A32
AP-60 Projector Sound SolutionV12H329020
Accolade Duet portable projector screenELPSC80
ES1000 Ultra Portable Tabletop Projection screenV12H002S4Y
ES3000 Ultra Portable Tabletop Projection screenV12H002S3Y
Universal projector ceiling mountELPMBPJF
Adjustable suspended ceiling channel kitELPMBP01
False ceiling plate kitELPMBP02
Structural round ceiling plateELPMBP03
Adjustable extension column (pipe) 8" - 11" (20 to 28 cm)ELPMBC01
VGA video cable 1.8 m lengthELPKC02
VGA video cable 3.0 m lengthELPKC09
VGA video cable 20 m lengthELPKC10
Kensington security lockELPSL01
In addition to the accessories listed above, 1-year and 2-year extended service plans are available.
Parent topic: Projector Features
Warranty and Registration Information
Your projector comes with a basic warranty that lets you project with confidence. For details, see the
warranty brochure that came with your projector.
In addition, Epson offers free Extra Care Home Service. In the unlikely event of an equipment failure,
you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit
anywhere in the United States, Canada, or Puerto Rico. See the Extra Care Home Service brochure for
details.
Register your product online using the projector CD or at this site: www.epson.com/webreg
Registering also lets you receive special updates on new accessories, products, and services.
Parent topic: Projector Features
12
Notations Used in the Documentation
Follow the guidelines in these notations as you read your documentation:
• Warnings must be followed carefully to avoid bodily injury.
• Cautions must be observed to avoid damage to your equipment.
• Notes contain important information about your projector.
• Tips contain additional projection information.
Parent topic: Projector Features
Where to Go for Additional Information
Need quick help on using your projector during a presentation? Here's where to look for help:
• Built-in help system
Press the Help button on the remote control or projector to get quick solutions to common problems.
• www.epson.com/support (U.S) or www.epson.ca/support (Canada)
View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24
hours a day.
• If you still need help after checking this manual and the sources listed above, you can use the EPSON
PrivateLine Support service to get help fast. For details, see "Where to Get Help".
Parent topic: Projector Features
Related references
Where to Get Help
Projector Part Locations
Check the projector part illustrations to learn about the parts on your projector.
Projector Parts - Front/Top
Projector Parts - Rear
Projector Parts - Base
Projector Parts - Control Panel
Projector Parts - Remote Control
Parent topic: Introduction to Your Projector
13
Projector Parts - Front/Top
1Exhaust vent
2Lamp cover
3Horizontal keystone slider
4Control panel
5Projector status lights
6Speaker
7Air filter cover
8Intake vent
9Zoom ring
10Focus ring
14
11Remote receiver
12A/V Mute slide
13Front adjustable foot
14Foot release lever
15A/V Mute slide lever
Parent topic: Projector Part Locations
Projector Parts - Rear
1Remote receiver
2Audio ports
3S-Video port
4USB TypeA/document camera port
5USB TypeB port
6Computer port
7HDMI port
8Lamp cover screw
15
9Kensington security lock slot
10Video port
11AC input port
Parent topic: Projector Part Locations
Related tasks
Installing a Security Cable
Projector Parts - Base
1Mounting bracket holes
16
2Front adjustable foot
3Rear feet
4Security cable attachment point
Parent topic: Projector Part Locations
Projector Parts - Control Panel
1Power button
2Source Search button (searches for connected sources)
3Menu button (accesses projector menu system)
4Enter button (selects options)
5Volume control buttons, horizontal keystone adjustment buttons (adjust screen shape), and arrow
Parent topic: Projector Part Locations
Related references
Projector Light Status
18
Projector Parts - Remote Control
1Power button
19
2Computer button (cycles through connected computer sources)
3Video button (cycles through connected video sources)
4Numeric buttons (enter numbers)
5Auto button (automatically adjusts position, tracking, and sync settings)
6Aspect button (selects the image aspect ratio)
7Num button (when held down, switches numeric buttons to number function)
8Menu button (accesses projector menu system)
9Arrow buttons (move through on-screen options and control wireless mouse functions)
10Enter button (selects options and controls wireless mouse functions)
11User button (customizable for different functions)
12Page up/down buttons (control presentation slides)
13E-Zoom +/– buttons (zoom into and out of the image)
14A/V Mute button (turns off picture and sound)
15Help button (accesses projector help information)
16Freeze button (stops video action)
17Volume up/down buttons (adjust speaker volume)
18Pointer button (activates on-screen pointer)
19Esc button (cancels/exits functions and controls wireless mouse functions)
20Color Mode button (selects display modes)
21LAN button (button is not functional)
22USB button (cycles through connected USB sources)
23Source Search button (searches for connected sources)
Parent topic: Projector Part Locations
20
Setting Up the Projector
Follow the instructions in these sections to set up your projector for use.
Projector Placement
Projector Connections
Installing Batteries in the Remote Control
Opening the Lens Cover
Projector Placement
You can place the projector on almost any flat surface to project your presentation.
You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Keep these considerations in mind as you select a projector location:
• Place the projector on a sturdy, level surface or install it using a compatible mount.
• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or
next to anything that could block the vents.
• Position the projector within reach of a grounded electrical outlet or extension cord.
Projector Setup and Installation Options
Projection Distance
Parent topic: Setting Up the Projector
Projector Setup and Installation Options
You can set up or install your projector to view presentations in the following ways:
Front
21
Rear
Front Ceiling
Rear Ceiling
Wherever you set up the projector, make sure to position it squarely in front of the center of the screen,
not at an angle, if possible.
If you project from the ceiling or from the rear, be sure to select the correct Projection option in the
projector's menu system.
Parent topic: Projector Placement
22
Related references
Projector Setup Settings - Extended Menu
Projection Distance
The distance at which you place the projector from the screen determines the approximate size of the
image. The image size increases the farther the projector is from the screen, but can vary depending on
the zoom factor, aspect ratio, and other settings.
Use the tables here to determine approximately how far to place the projector from the screen based on
the size of the projected image. (Conversion figures may have been rounded up or down.)
16:10 Aspect Ratio
Screen orProjection distance
image size
150 inches55 to 66 inches (139 to 168 cm)
280 inches88 to 106 inches (225 to 270 cm)
3100 inches111 to 133 inches (281 to 338 cm)
4150 inches167 to 200 inches (424 to 509 cm)
16:9 Aspect Ratio
Wide to Tele
23
Screen orProjection distance
image size
150 inches56 to 68 inches (143 to 172 cm)
280 inches91 to 110 inches (231 to 278 cm)
3100 inches114 to 137 inches (289 to 348 cm)
4150 inches171 to 206 inches (435 to 523 cm)
4:3 Aspect Ratio
Screen orProjection distance
image size
150 inches62 to 75 inches (158 to 190 cm)
280 inches100 to 120 inches (255 to 306 cm)
3100 inches126 to 151 inches (319 to 383 cm)
4150 inches189 to 227 inches (480 to 577 cm)
Parent topic: Projector Placement
Related references
General Projector Specifications
Wide to Tele
Wide to Tele
Projector Connections
You can connect the projector to a variety of computer, video, and audio sources to display
presentations, movies, or other images, with or without sound.
• Connect any type of computer that has a USB port, standard video output (monitor) port, or HDMI port.
• For video projection, connect devices such as DVD players, gaming consoles, digital cameras, and
camera phones with compatible video output ports.
• If your presentation or video includes sound, you can connect audio input cables, if necessary.
• For slide shows without a computer, you can connect USB devices (such as a flash drive or camera)
or an optional EPSON document camera.
Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode
to ensure the projector's internal temperature is regulated properly.
24
Connecting to Video Sources
Connecting to Computer Sources
Connecting to External USB Devices
Connecting to a Document Camera
Parent topic: Setting Up the Projector
Related references
Projector Setup Settings - Extended Menu
Product Box Contents
Connecting to Video Sources
Follow the instructions in these sections to connect video devices to the projector.
Connecting to an HDMI Video Source
Connecting to a Component-to-VGA Video Source
Connecting to an S-Video Video Source
Connecting to a Composite Video Source
Connecting to a Video Source for Sound
Parent topic: Projector Connections
Connecting to an HDMI Video Source
If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.
The HDMI connection provides the best image quality.
1.Connect the HDMI cable to your video source's HDMI output port.
2.Connect the other end to the projector's HDMI port.
25
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce
the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your
game console documentation for instructions.
Parent topic: Connecting to Video Sources
Connecting to a Component-to-VGA Video Source
If your video source has component video ports, you can connect it to the projector using a componentto-VGA video cable. Depending on your component ports, you may need to use an adapter cable along
with a component video cable.
1.Connect the component connectors to your video source's color-coded component video output
ports, usually labeled Y, Pb, Pr or Y, Cb,Cr.Ifyouareusinganadapter,connecttheseconnectors
to your component video cable.
2.Connect the VGA connector to the projector's Computer port.
If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's
Signal menu.
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce
the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your
game console documentation for instructions.
Parent topic: Connecting to Video Sources
Related references
Input Signal Settings - Signal Menu
26
Related tasks
Connecting to a Video Source for Sound
Connecting to an S-Video Video Source
If your video source has an S-Video port, you can connect it to the projector using an optional S-Video
cable.
1.Connect the S-Video cable to your video source's S-Video output port.
2.Connect the other end to the projector's S-Video port.
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce
the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your
game console documentation for instructions.
Parent topic: Connecting to Video Sources
Related tasks
Connecting to a Video Source for Sound
Connecting to a Composite Video Source
If your video source has a composite video port, you can connect it to the projector using an optional
RCA-style video or A/V cable.
1.Connect the cable with the yellow connector to your video source's yellow video output port.
27
2.Connect the other end to the projector's Video port.
Note: If you connected a game console, it may take a few seconds for your image to appear. To reduce
the lag time, set your game console's input signal to a progressive signal of 480p or 720p. See your
game console documentation for instructions.
Parent topic: Connecting to Video Sources
Related tasks
Connecting to a Video Source for Sound
Connecting to a Video Source for Sound
You can play sound through the projector's speaker system if your video source has audio output ports.
Connect the projector to the video source using an RCA audio cable.
1.Connect the audio cable to your video source's audio-out ports.
2.Connect the other end of the cable to the projector's Audio ports.
28
Parent topic: Connecting to Video Sources
Connecting to Computer Sources
Follow the instructions in these sections to connect a computer to the projector.
Connecting to a Computer for USB Video and Audio
Connecting to a Computer for VGA Video
Connecting to a Computer for HDMI Video and Audio
Connecting to a Computer for USB Mouse Control
Connecting to a Computer for Sound
Parent topic: Projector Connections
Connecting to a Computer for USB Video and Audio
If your computer meets the system requirements, you can send video and audio output to the projector
through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a
USB cable.
1.In the projector's Extended menu, set the USB Type B setting to USB Display.
2.Turn on your computer.
3.Connect the cable to your projector's USB TypeB port.
4.Connect the other end to any available USB port on your computer.
5.Do one of the following:
• Windows 7/Windows Vista: Select Run EMP_UDSe.exe in the dialog box that appears to install
the EPSON USB Display software.
• Windows XP: Wait as messages appear on your computer screen and the projector installs the
EPSON USB Display software on your computer.
29
• Windows 2000: Select Computer, EPSON_PJ_UD, and EMP_UDSe.EXE to install the EPSON
USB Display software.
• Mac OS X: The USB Display setup folder appears on your screen. Select USB Display Installer
and follow the on-screen instructions to install the EPSON USB Display software.
Follow any on-screen instructions. You need to install this software only the first time you connect
the projector to the computer.
The projector displays the image from your computer's desktop and outputs sound, if your presentation
contains audio.
Parent topic: Connecting to Computer Sources
Related references
Projector Setup Settings - Extended Menu
USB Display System Requirements
Connecting to a Computer for VGA Video
You can connect the projector to your computer using a VGA computer cable.
Note: To connect a Mac that includes only a Mini DisplayPort or Mini-DVI port for video output, you need
to obtain an adapter that allows you to connect to the projector's VGA video port. Contact Apple for
compatible adapter options.
1.If necessary, disconnect your computer's monitor cable.
2.Connect the VGA computer cable to your computer's monitor port.
3.Connect the other end to a Computer port on the projector.
4.Tighten the screws on the VGA connectors.
Parent topic: Connecting to Computer Sources
30
Loading...
+ 138 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.