Epson PowerLite Home Cinema 3010e User Manual
60º
16.5 ft (5 m)
13 ft (4 m)
PowerLite® Home Cinema 3010/3010e
*412153700*
*412153700*
Computer
Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Choose a location
Keep the projector level and place it at a height where its lens is centered
between the top and bottom of the screen. If this isn’t possible, use the
horizontal keystone slider and keystone correction buttons to reposition the
image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within proper
range of the projector. Use the image below to determine the ideal distance for
3D projection (the shading represents the 3D viewing area):
HDMI cable
VGA cable
Monitor Port
Connect one end of a VGA cable to the projector’s PC port, and the other end
to your computer’s monitor port. If you are using a laptop, switch it to
external display (see “Troubleshooting”). You can also connect an audio cable.
HDMI Port
Connect one end of an HDMI cable to the projector’s HDMI port and the other
end to an HDMI port on your computer.
Camera or USB Device
Connect a digital camera, USB flash drive, or USB storage device to the
projector’s USB port.USB port.
Use the optional external 3D emitter if the projector is located over
16.5 feet (5 m) from the viewing area. See “Optional accessories” on the back
of this sheet for ordering information, and the online User’s Guide for more
information on where to place your projector.
Connect the projector
Choose from the following connections. See the sections below or the online
User's Guide for details.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
HDMI cable
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s Slideshow feature to project images. See the online User’s
Guide for details.
Turn on your equipment
Turn on your video source or computer.
1
Plug in the projector. The power button on the projector turns blue.
2
Remove the lens cap.
3
RCA Video cable
Audio cable
Component video cable
Audio cable
Press the power button on the projector or On button on the remote
4
control. The power light flashes blue, and then stays on.
Note: To shut down the projector, press the power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
The default language of the menu system is English. To select another
5
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
Adjust the image
Using the remote control
If you don’t see an image, press the Source buttons on the projector or
1
the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
To raise the image, adjust the front feet as shown below.
2
Turn the zoom ring to reduce or enlarge the image.
3
Make sure the batteries are installed as shown (two AA batteries).
Turn projector on
Switch between
2D and 3D
Turn projector off
Choose which source
to display
Navigate projector
menus
Turn the focus ring to sharpen the image.
4
If your image looks like or , you’ve placed the projector off to
5
one side of the screen at an angle. Use the horizontal keystone slider on
the projector to correct it. Or place the projector directly in front of the
center of the screen, facing the screen squarely.
Access projector
menus
Turn off projector
display
For more information on using the remote control, see the online User’s
Guide.
Project wirelessly
(PowerLite Home Cinema 3010e only)
Follow these steps to use the included WirelessHD Transmitter (PowerLite
Home Cinema 3010e only) to wirelessly transmit HD content to your projector.
6 Your projector automatically adjusts images that look like or ,
but if necessary you can press the or buttons on the projector to
correct this.
Place the transmitter within 30 feet (10 m) of the projector. Make sure
1
the front of the transmitter faces the front of the projector. See the
online User’s Guide for more information on the WirelessHD transmission
range.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal.
Plug the AC adapter into the transmitter and a wall outlet.
2
Connect an HDMI cable to your video device and the HDMI port on the
3
side of the transmitter.
Turn on the power switch on the back of the transmitter.
4
Turn on your video device and begin playback.
5
Turn on the projector.
6
Press the button on the projector remote control.
7
See the online User’s Guide for more information on adjusting and configuring
the WirelessHD connection.
Loading...