Epson PowerLite G5000 User Manual

PowerLite® G5000

Multimedia Projector

User’s Guide

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson, Quick Corner, and Instant Off are registered trademarks, and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

PowerLite and PrivateLine are registered trademarks; SizeWise is a trademark; and Extra Care is a service mark of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8

Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setting Up the Projector . . . . . . . . . . . . . . . . . . . . . 11

Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 12

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 16

Connecting a Composite Video Source . . . . . . . . . . . . . 17

Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 18

Connecting a Component Video Source . . . . . . . . . . . . 19

Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 20

Playing Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting a Network Cable . . . . . . . . . . . . . . . . . . . . . . . . 23

Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . 24

Using the Direct Power On Function . . . . . . . . . . . . . . 25

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . 26

Displaying and Adjusting the Image . . . . . . . . 27

Displaying an Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 28

You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . . 28

The Projector and Notebook Don’t Display the

Same Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Adjusting the Position of the Image . . . . . . . . . . . . . . . . 31

Focusing and Zooming the Image . . . . . . . . . . . . . . . . . 32

Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 33

Selecting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 35

Resizing Video Images . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Presenting With the Remote Control. . . . . . . . 37

Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 38

Switching Between Picture Sources . . . . . . . . . . . . . . . . 38

Turning Off the Picture and Sound. . . . . . . . . . . . . . . . 39

Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Zooming Part of Your Image . . . . . . . . . . . . . . . . . . . . . 40

Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 40

Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 41

Using the Pointer Tool . . . . . . . . . . . . . . . . . . . . . . . . . 41

Choosing a Different Pointer Shape. . . . . . . . . . . . . . . . 41

Operating Your Computer With the Remote Control . . . . . 42

Operating Two or More Projectors With the

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Setting the Projector ID. . . . . . . . . . . . . . . . . . . . . . . . . 43

Checking the Projector ID. . . . . . . . . . . . . . . . . . . . . . . 44

Setting the Remote Control ID . . . . . . . . . . . . . . . . . . . 44

Fine-Tuning the Projector. . . . . . . . . . . . . . . . . . . 45

Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 47

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Six-Axis Color Adjustment. . . . . . . . . . . . . . . . . . . . . . . 49

Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 52

Using the Projector Security Features . . . . . . . . . . . . . . . . . . 54

Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 54

Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 56

Disabling the Projector’s Buttons. . . . . . . . . . . . . . . . . . 58

Customizing Power and Operation . . . . . . . . . . . . . . . . . . . 59

Multi-screen Color Adjustment . . . . . . . . . . . . . . . . . . . . . . 61

Projector Menu and Options List . . . . . . . . . . . . . . . . . . . . . 62

Managing Projectors. . . . . . . . . . . . . . . . . . . . . . . . . 65

Connecting to a Wired Network . . . . . . . . . . . . . . . . . . . . . 65

Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . 67

Maintaining the Projector. . . . . . . . . . . . . . . . . . . 69

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 70

Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Replacing the Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 77

Checking Lamp Usage . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Checking Projector Status. . . . . . . . . . . . . . . . . . . . . . . . . . . 83

What To Do When the Lights Flash . . . . . . . . . . . . . . . 83

Solving Projector Operation Problems . . . . . . . . . . . . . . . . . 85

Solving Problems With the Image or Sound . . . . . . . . . . . . . 85

Solving Network Problems . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Solving Problems With the Remote Control. . . . . . . . . . . . . 92

Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Speak to a Support Representative . . . . . . . . . . . . . . . . . 93

Projector Installation . . . . . . . . . . . . . . . . . . . . . . . . 95

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Security Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Installing and Removing the Lens. . . . . . . . . . . . . . . . . . . . . 97

Removing the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Installing the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Technical Specifications . . . . . . . . . . . . . . . . . . . . . 99

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . 105

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 108

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Welcome

The PowerLite

G5000 is an easy-to-use, flexible for installation projector. It offers up to 4000 lumens of brightness (white and color light output) and provides a native XGA resolution. You can connect it to a wide range of computers and video sources.

Your projector offers these easy setup, control, and security features:

■ Manual horizontal and vertical lens shift

■ Centered lens design

■ Instant Off

■ Quick Corner

■ 1.8x optical zoom lens for flexible placement and positioning

■ One-touch filter replacement

■ Side-loading easy lamp access

■ Security features include password, user’s logo, the ability to lock

feature for fast setup and shut down

for easy image shape/size adjustment

the projector buttons, a security cable attachment (cable not

included), a slot for an optional Kensington

security lock, and a

lens theft deterrent screw

Additional enhancements:

■ Closed captioning for the hearing impaired

■ 1000:1 contrast ratio

■ Perform six-axis color adjustment for fine art and photography

Using Your Documentation

This electronic User’s Guide contains all the information you need to set up and use your projector.

In addition, your projector CD-ROM includes the EMP Monitor Operation Guide. Refer to this manual for detailed instructions on monitoring the projector from a remote location.

Please follow these guidelines as you read through this manual:

■ Warnings must be followed carefully to avoid bodily injury.

■ Cautions must be observed to avoid damage to your equipment.

■ Notes contain important information about your projector.

■ Tips contain additional projection hints.

Getting More Information

Need quick steps for setting up your projector or other assistance? Here’s where you can look for help:

■ Quick Reference card

Provides information for connecting the projector to your equipment, displaying and adjusting the image, using the remote control, and solving display problems.

8 Welcome

■ Built-in help system

Provides assistance for common problems. Available from the

Help button on the projector or the remote control. See page 82

for details.

■ epson.com/support

Download FAQs and e-mail your questions to Epson support.

■ PrivateLine support

If you still need help after checking this User’s Guide and the sources listed in this section, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the PrivateLine card. Or take advantage of Epson’s automated support services 24 hours a day. See page 93 for more information.

Registration and Warranty

Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure included with your projector.

In addition, Epson offers free Extra Care unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via next business day delivery. See the brochure included with your projector for details.

To register, simply fill out the registration card and mail it to Epson. Or you can register online at epson.com/webreg you receive special updates on new accessories, products, and service.

Road Service. In the

. Registering also lets

Welcome 9

Optional Accessories

To enhance your use of the projector, Epson offers the following optional accessories:

Product Part number

Replacement lamp for PowerLite G5000 V13H010L47

Replacement air filter V13H134A17

Wireless IR mouse receiver for remote control V12H007T16

Replacement remote control 1485872

Advanced projector ceiling mount with precision gear Adjustable suspended ceiling channel kit False ceiling plate kit Structural round ceiling plate Adjustable extension column (pipe) 8”–11”

Kensington

50-inch portable screen (4:3 aspect ratio) 60-inch portable pop-up screen (4:3 aspect ratio) 80-inch portable pop-up screen (4:3 aspect ratio) DUET Portable Projector Screen (4:3/16:9 combination)

Component-to-VGA cable S-video cable

Distribution amplifier ELPDA01

Image presentation camera (ELPDC05) V12H162020

MicroSaver® security lock ELPSL01

ELPMBPRG ELPMBP01 ELPMBP02 ELPMBP03 ELPMBC01

ELPSC06 ELPSC07 ELPSC08 ELPSC80

ELPKC19 ELPSV01

10 Welcome

You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca

(Canadian sales).

Setting Up the Projector

This chapter tells you how to unpack the projector and connect it to

a notebook or desktop computer, to video equipment (such as a VCR, DVD player, or video camera), and to a local area network.

Follow the instructions in this chapter for:

■ Unpacking the projector

■ Positioning the projector

■ Connecting to a computer

■ Connecting to video equipment

■ Playing Sound

■ Connecting a network cable

■ Turning the projector on and off

Unpacking the Projector

After unpacking the projector, make sure you have all these parts:

Projector and lens cap

Lens theft

deterrent screw

Power cord

PDF manuals and

registration CD-ROM

Remote control and

2 AA batteries

VGA computer cable

Projector software

CD-ROM

Password Protected

sticker

Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use the projector handle. See page 79 for transportation instructions.

12 Setting Up the Projector

Additional Components

Depending on how you plan to use the projector, you may need additional components:

■ To receive a composite video signal from a VCR or other video

device, you’ll need a video cable. One may be provided with your video equipment.

■ To receive an S-video signal, you’ll need an S-video cable. One

may be included with your video equipment, or you can purchase one from Epson. See “Optional Accessories” on page 10.

Positioning the Projector

If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it. Try to leave as much space as possible between the projector and the screen to get a good-size image.

Use the illustration below to help you determine placement. Image size increases with distance, but can vary depending on how you position the zoom ring and whether you’ve adjusted the image with other settings.

(4:3 image)

TBD

note

You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 95 for details.

26.5 to 47.8 ft (8.1 to 14.6 m)

5.2 to 9.4 ft (1.6 to 2.9 m)

2.5 to 4.6 ft (0.8 to 1.4 m)

Distance from screen

Also keep these considerations in mind:

■ Place the projector on a sturdy, level surface.

■ Make sure there is plenty of space for ventilation around and

under the projector.

■ Make sure the projector is within 10 feet (3 meters) of a grounded

electrical outlet or extension cord.

Setting Up the Projector 13

note

After positioning the projector, you may want to connect a Kensington MicroSaver device to the lock port on the projector. You can purchase this from Epson; see page 10.

anti-theft

Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be about level with the bottom of the screen.

Projector

Screen

If you place the projector below screen level, you can use the vertical lens shift dial to raise the lens (see page 32). You can also tilt the projector up by extending the front adjustable foot. Tilting the projector causes the image to become “keystone” shaped, but you can correct the distortion (see page 33).

For instructions on installing the projector in a permanent location, such as a theater or conference room, see page 95.

14 Setting Up the Projector

Connecting to a Computer

You can connect the projector to any computer that has a standard video output (monitor) port, including desktop models, PC notebook

computers, MacBook hand-held devices.

If you have the optional wireless mouse receiver, you can use your remote control as a wireless mouse when projecting from a computer (page 42).

Follow these steps to connect to the projector using the VGA computer cable that came with it (the monitor port on your computer must be a mini D-sub 15-pin port).

, PowerBook®, and iBook® computers, and

1. Connect one end of the cable to the projector’s

Computer 2 port, and the other end to your computer’s monitor

Computer1 or

port.

2. You may need to change the Input Signal setting in the projector’s Signal menu to

RGB (see page 51).

3. To play sound, you can connect an optional stereo mini-jack audio cable and optional external speakers (see page 21).

4. When you’ve finished making any connections, see page 24 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.

caution

Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector.

Setting Up the Projector 15

Connecting to Video Equipment

You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections:

■ If your video player has a component video port (three connectors

labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a Component Video Source” on page 19.

■ If your video player has a yellow RCA video output connector, or

if you’re using a composite cable with a BNC connector, see “Connecting a Composite Video Source” on page 17.

BNC connector

(component or

composite video)

■ If your video player has an S-video connector, see “Connecting an

RCA connector

(composite video)

S-Video Source” on page 18.

S-video

connector

■ If your video player has an RGB video port (either a single

connector for a VGA monitor cable or three connectors labeled R/G/B), see “Connecting an RGB Video Source” on page 20.

VGA connector

(RGB video)

16 Setting Up the Projector

Connecting a Composite Video Source

1. If your video cable has an RCA connector, connect it to the yellow video output connector on your player and the yellow

Video2 connector on the projector (as shown below). Or if you’re

using a coax video cable, connect it to the the projector.

2. To play sound, you can connect an optional stereo mini-jack audio cable and optional external speakers (see page 21).

Video1 connector on

note

If the video cable was not

rovided with your video

device, you can purchase one

rom an electronics dealer.

3. When you’ve finished making any connections, see page 24 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.

Setting Up the Projector 17

note

If the S-video cable was not

rovided with your video

device, you can purchase one

rom Epson; see page 10.

Connecting an S-Video Source

1. Connect the S-video cable to the S-video connector on your player and the

2. To play sound, you can connect an optional stereo mini-jack audio cable and optional external speakers (see page 21).

3. When you’ve finished making any connections, see page 24 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.

S-Video connector on the projector.

18 Setting Up the Projector

Connecting a Component Video Source

You will need a special cable to connect your component video equipment to the VGA-style connector on the projector. You can order a component-to-VGA cable (part number ELPKC19) from Epson; see page 10 for more information.

1. Locate a component-to-VGA cable.

2. Connect the cable to your player and the

Computer 2 connector on the projector.

Component-to-VGA cable

3. You may need to change the projector’s Signal menu to

Input Signal setting in the

Component (see page 51).

Computer 1 or

4. To play sound, you can connect an optional stereo mini-jack audio cable and optional external speakers (see page 21).

5. When you’ve finished making any connections, see page 24 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.

note

Be sure your video player is not an RGB video source. If you select the wrong source, image quality may suffer. Check your video

layer’s documentation.

Also, make sure the Input Signal setting in the Signal menu is set to

Component Video (see

age 51).

Auto or

Setting Up the Projector 19

note

Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation.

Connecting an RGB Video Source

1. Locate the VGA computer cable provided with the projector (or if your video player has three connectors labeled R/G/B, locate a component-to-VGA cable as shown on page 19).

2. Connect the cable to the video port(s) on your player and

Computer1 or Computer2 port on the projector.

the

20 Setting Up the Projector

3. You may need to change the projector’s Signal menu to

Input Signal setting in the

RGB (see page 51).

4. To play sound, you can connect an optional stereo mini-jack audio cable and optional external speakers (see page 21).

5. When you’ve finished making any connections, see page 24 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.

Playing Sound

You can play sound by connecting external speakers with built-in amplifiers. You can use the remote control or the projector’s menu system to adjust the volume.

Follow these steps to connect your equipment and external speakers to the projector:

1. Locate the appropriate cable and connect it to the audio port(s) on the projector.

■ If you have equipment connected to the Computer1 or

Computer2 ports, use a stereo mini-jack cable. Connect the

cable to the

Audio port beneath the Computer2 port.

■ If you have equipment connected to the Video1, Video2,

S-Video ports, connect an RCA audio cable to the

L and R Audio (Video) ports.

Setting Up the Projector 21

2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment.

3. Locate the appropriate cable to connect your speakers.

Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter.

4. Connect the stereo mini-jack end of the audio cable to the

Audio Out port on the projector.

22 Setting Up the Projector

5. Connect the other end of the cable to your speakers.

Connecting a Network Cable

To connect the projector to your local area network (LAN), use a commercially available 100BaseTX or 10BaseT network cable. To ensure proper data transmission, use a Category 5 shielded cable or better.

Connect the cable to the projector and your network port as shown:

LAN port

Setting Up the Projector 23

note

You can set the projector to automatically turn off the lamp and enter “sleep mode” when it has not received any signals for 10 minutes (see page 60 to enable, disable, or adjust this setting). This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the you are done using the projector, unplug the power cord.

P power button. If

Turning the Projector On and Off

Turn on any connected computer or video equipment before starting the projector so it can automatically detect and display the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually (see page 28).

Follow these steps to turn on the projector:

1. Remove the lens cover.

2. Plug one end of the power cord into the projector, and the other end into an electrical outlet.

The Ppower light turns orange.

24 Setting Up the Projector

Power light

3. Press the Ppower button on the remote control or on the back of

the projector.

Power button

The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use.

4. If you are prompted to enter a password, see page 55.

Using the Direct Power On Function

The Direct Power On function enables faster setup. The projector starts up automatically when you plug it in or turn it on with a wall switch. You don’t have to press the Ppower button.

Follow these steps to enable Direct Power On:

1. Press the select the

2. Choose

3. Choose

4. Highlight

5. Press plug in the projector.

Menu button on the remote control or projector, then

Extended menu and press Enter.

Operation and press Enter.

Direct Power On and press Enter.

On and press Enter.

Menu to exit. The setting will take effect the next time you

warning

Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.

note

If a power outage occurs when Direct Power On is enabled and the projector is plugged in, the projector will restart when the power is restored.

Setting Up the Projector 25

note

Lamp life results depend upon the Brightness Control setting you’ve selected, environmental conditions, and usage.

Turn off this product when not in use to prolong the life of the projector.

Shutting Down the Projector

This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool down first.

1. To turn off the projector, press the Ppower

control or projector.

You see a confirmation message. (If you don’t want to turn it off, press any other button.)

2. Press the Ppower button again. The projection lamp turns off

and the projector beeps twice. You can unplug the power cord.

If you want to turn the projector on again, make sure the orange P power light is not flashing, then press the Ppower button.

button on the remote

26 Setting Up the Projector

Displaying and Adjusting the Image

Follow the guidelines in this chapter for:

■ Displaying an image

■ Troubleshooting display problems

■ Adjusting the image

note

The BNC, EasyMP, and

HDMI buttons are not

applicable to this projector.

Displaying an Image

You may need to select the image source if you have multiple video sources connected to the projector (such as a computer or DVD player). Selecting the image source lets you switch between images input from different pieces of connected equipment.

If you don’t see the image you want, press the of the

Source buttons on the remote control, or the Source Search

button on the projector until you see the image you want to project.

Search button or one

You can also use the between devices connected to the ports identified on each button.

Source buttons on the remote control to switch

Troubleshooting Display Problems

Follow these guidelines if you’re having trouble displaying an image.

You Can’t Project an Image

If you don’t see the image you are trying to project, try the following:

■ Make sure the cables are connected correctly, as described

beginning on page 11.

■ Make sure the P power light is green and not flashing and the

lens cover is removed.

28 Displaying and Adjusting the Image

■ If you’ve connected more than one computer and/or video source,

you may need to press the projector’s control panel, or the

Source buttons on the remote control to select the correct source.

Source Search button on the

Search button or one of the

(Allow a few seconds for the projector to sync up after pressing the button.)

■ If you’re using a PC notebook, press the function key on your

keyboard that lets you display on an external monitor. It may be labeled hold down the

CRT/LCD or have an icon such as . You may have to

Fn key while pressing it. Allow a few seconds for

the projector to sync up after changing the setting.

The Projector and Notebook Don’t Display the Same Image

If you’re projecting from a notebook, and you can’t see your image on the projection screen and on your computer at the same time, follow these guidelines.

If you’re using a PC notebook:

■ On most systems, there’s a function key that lets you toggle

between the LCD screen and the projector, or display on both at the same time. It may be labeled

. You may have to hold down the Allow a few seconds for the projector to sync up after changing the setting.

CRT/LCD or have an icon such as

Fn key while pressing it.

■ If the function key doesn’t permit you to display simultaneously

on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.

From the Control Panel, open the Properties dialog box, click the

Advanced. The method for adjusting the settings varies by

brand; you may need to click a

Display utility. In the Display

Settings tab, then click

Monitor tab, then make sure the

external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.

Displaying and Adjusting the Image 29

If you’re using Mac OS X:

You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:

1. From the Apple

menu, select System Preferences.

2. Select

3. Make sure the

4. Click the

5. Make sure the

Displays, then click Detect Displays.

VGA Display or Color LCD dialog box is selected.

Arrangement or Arrange tab.

Make sure Mirror Displays is checked

Mirror Displays checkbox is selected.

Adjusting the Image

Once you see your image, you need to make certain adjustments:

■ If the image is too high or too low, reposition it as described on

page 31.

■ To focus or zoom your image, see page 32.

■ If the image isn’t square, see page 33.

■ To quickly adjust the color, brightness, or contrast, see page 35.

■ To change the image aspect ratio, see page 36.

■ If you need to fine-tune the image and/or sound, see Chapter 4.

30 Displaying and Adjusting the Image

Adjusting the Position of the Image

If the image is too low on the screen, you can use the front adjustable foot to raise it.

1. Stand behind the projector. Press the foot release lever up and lift the front of the projector.

2. Once the image is positioned where you want it, release the lever to lock the foot in position.

3. If necessary, you can fine-tune the height or level the image by turning any of the projector’s adjustable feet.

Raising the projector causes the image shape to distort or “keystone,” but you can correct the shape as described on page 33.

Displaying and Adjusting the Image 31

Additionally, you can use the vertical lens shift dial on the top of the projector to move your image up or down, or you can use the horizontal lens shift dial to move your image left or right.

Vertical Horizontal

Focusing and Zooming the Image

Turn the focus ring on the projector to sharpen the image.

Turn the zoom ring (using the knobs on the ring) to reduce or enlarge the image.

If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the buttons on the remote control to zoom in on a portion of the image. See page 40 for instructions.

32 Displaying and Adjusting the Image

Focus Zoom

E-Zoom

Adjusting the Image Shape

You can maintain a square or rectangular image by placing the projector directly in front of the screen and keeping it level. This also produces the best picture quality. If the projector is tilted up or placed at an angle, you’ll need to correct the image shape by using one of the functions described below.

Using Quick Corner

Use Quick Corner to adjust the shape and size of the image when it’s uneven on all sides. Follow these steps to select

Quick Corner:

1. Press the

2. Select the

3. From the Settings menu, select

4. Select

Menu button on the remote control or the projector.

Settings menu and press Enter.

Keystone and press Enter.

Quick Corner and press Enter twice.

You see this screen:

5. Use the pointer button on the remote control (or the arrow buttons on the projector) to select the corner you want to adjust, and press

Enter.

6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape, then press

Esc when

you are finished.

7. Repeat steps 5 and 6 as needed to adjust the other corners.

8. When you’re done, press

Menu to exit.

Displaying and Adjusting the Image 33

Using Keystone Correction

You can manually adjust the shape of the image to compensate for vertical and horizontal keystone distortion. First make sure the Keystone setting in the projector’s menu system is set to

V-Keystone:

H-Keystone

note

Use can also use the projector’s arrow buttons to perform keystone correction as long as the projector’s Keystone setting is set to

H/V-Keystone.

1. Press the

2. Select the

3. From the Settings menu, select

4. Select

5. Select

Menu button on the remote control or projector.

Settings menu and press Enter.

Keystone and press Enter.

H/V-Keystone and press Enter.

H-Keystone (for horizontal adjustment) or V-Keystone

(for vertical adjustment) and use the pointer button on the remote control to adjust the shape of the image.

Vertical keystone adjustment

Horizontal keystone adjustment

If the image becomes smaller, use the zoom ring to enlarge the image so it fits the screen. If the image contains faint lines or a gridlike pattern, decrease the sharpness setting (see page 49).

6. When you’re done, press

34 Displaying and Adjusting the Image

Menu to exit.

Selecting the Color Mode

The Color Mode adjusts the brightness, contrast, and color for various common viewing environments. Use this setting to quickly obtain a good picture.

Press the

Color Mode button on the remote control, and then select

from one of these options:

■ Presentation: For making color presentations in a bright room.

■ Text: For making black-and-white presentations in a bright

room.

■ Theatre: For watching movies in a darkened room; gives images a

natural tone.

■ Photo: For vivid, high-contrast still images in a bright room (only

available when the source is set to

■ Sports: For vivid TV images projected in a bright room

Computer1 or Computer2).

(component video, S-video, or composite video only).

■ sRGB: Matches the color palette of standard sRGB computer

displays.

■ Blackboard: Projects accurate colors on a green chalkboard

(adjusts the white point).

■ Customized: For manual color adjustment (see page 49).

■ Game: Increases brightness when playing video games or

watching TV in a bright room. Emphasizes dark gradations.

Displaying and Adjusting the Image 35

Resizing Video Images

You can use the Aspect button on the remote control to change the aspect (width to height) ratio, depending on the input signal.

■ Normal (for images sent through the Computer1 or Computer2

ports only) maintains the aspect ratio of the image. Choose this setting to automatically resize the image and make the best use of the display area.

■ 4:3: Displays images using the full projection area at an aspect

ratio of 4:3.

■ 16:9: Converts the aspect ratio of the image to 16:9. 4:3 ratio

images are elongated horizontally to fit.

■ Through: Displays images as is (aspect ratio and resolution are

maintained). Black bands appear if the resolution is less than 1024 × 768; images are cut off if the resolution is over 1024 × 768.

: Displays images using the full projection area and

Press the

Aspect button repeatedly to cycle through the available

options.

You can also change the aspect ratio using the projector’s Signal menu. See page 50 for details.

36 Displaying and Adjusting the Image

Presenting With the Remote Control

The projector includes a number of tools to enhance your

presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 49 feet (15 meters) away.

You can use the remote control to adjust the picture and sound (page 38), as a pointer to highlight your presentation (page 41), or to control two or more projectors at the same time (page 43). If you have the optional wireless mouse receiver, you can also use your remote control as a wireless mouse when projecting from a computer (page 42).

This chapter covers:

■ Using the remote control

■ Controlling the picture and sound

■ Highlighting your presentation

■ Operating your computer with the remote control

■ Operating two or more projectors with the remote control

note

If a button is pressed longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes.

Using the Remote Control

Make sure batteries are installed as described on page 78. Follow these tips for using the remote control:

■ Point the remote control at the front of the projector or at the

screen.

■ Stand within 49 feet (15 meters) of the projector.

Controlling the Picture and Sound

note

Using the remote under bright fluorescent lamps or in direct sunlight may affect projector response.

note

The BNC, EasyMP, and

HDMI buttons are not

applicable to this projector.

You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.

Switching Between Picture Sources

If your projector is connected to more than one computer and/or video source, you can switch between the different sources:

■ The easiest way to select your source is to press the Search button

on the remote control (or the projector) repeatedly until you see the image you want on the screen.

Source Search button on the

■ On the remote control, you can press one of the Source buttons

to select the connected device you need.

After you select a source, the screen goes dark for a moment before the image appears.

38 Presenting With the Remote Control

Turning Off the Picture and Sound

You can temporarily turn off the image and sound by pressing the

A/V Mute button on the remote control. This turns the image black

and stops the sound. To turn the image and sound back on, press the button again.

You can have the screen turn blue (using the Display setting as described on page 59) or display an image such as a company logo when you press the information on displaying an image.)

A/V Mute button. (See page 56 for more

note

In order to play sound with this projector, you must connect optional external speakers (see page 21).

Stopping Action

Press the Freeze button on the remote control to stop the action in your video or computer image. The image freezes but the sound continues.

To restart the action, press the

Freeze button again.

note

This function pauses the image, not the sound. Because the source continues to transmit signals, when you resume the action, it won’t be at the point you stopped it.

Presenting With the Remote Control 39

Zooming Part of Your Image

You can zoom in on a portion of the image using the E-Zoom buttons on the remote control.

note

You cannot use the Progressive or Noise Reduction features (see page 50) while you are using E-Zoom.

note

To temporarily shut off the sound and picture, press the

A/V Mute button.

1. Press the

E-Zoom button on the remote control.

You see a crosshair indicating the center of the zoom-in area.

2. Use the pointer button to position the crosshair.

3. Continue pressing the

E-Zoom button to enlarge the selected

area up to 4 times.

4. While the image is enlarged, you can:

■ Use the pointer button to move around the screen.

■ Press the E-Zoom button to zoom out.

5. When done, press the

ESC button to return the image to its

original size.

Controlling the Volume

To change the volume, press the or button on the remote control.

You can also adjust the volume using the projector’s menu system. See page 53.

40 Presenting With the Remote Control

Highlighting Your Presentation

You can display a pointer to call out important information on the screen, and you can choose from three shapes for the pointer.

Using the Pointer Tool

1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen.

Pointer

If you prefer to use a different style of pointer, see the instructions in the next section.

2. Use the pointer button on the remote control to position the pointer on the screen.

3. When you’re done using the pointer, press the clear the screen.

Pointer button to

Choosing a Different Pointer Shape

Follow these steps to select a different pointer shape:

1. Press the

Settings menu, highlight Pointer Shape, and press Enter. You

can select one of the pointer shapes shown at the right.

2. Select the shape you want and press

3. Press

Menu button on the remote control, highlight the

Enter.

Menu to exit.

Presenting With the Remote Control 41

Operating Your Computer With the Remote Control

With the optional wireless mouse receiver (see page 10), you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides.

■ Use the Up and Down buttons to move through a

Microsoft

Left-click

Page up or down to change slides in PowerPoint

PowerPoint slideshow.

Use to move pointer on screen

Right-click

■ Use the pointer button to move the pointer on the screen.

■ Press the Enter button once to left-click, or twice to double-click.

Press the

■ To drag-and-drop, hold down the Enter button. Then use the

pointer button to drag the object. When it’s where you want

it, release the

42 Presenting With the Remote Control

Esc button to right-click.

Enter button.

Operating Two or More Projectors With the Remote Control

If you’re using more than one projector, you can control all the projectors—or just selected ones—by using the projector ID system. To operate a projector, set the remote control’s ID to match that of the projector. Or you can control all the projectors at once by setting the remote control’s ID to zero.

Setting the Projector ID

The projector’s default ID is set to Off. This lets it respond to commands from any remote control. To change the ID, follow these steps:

1. Press the projector’s menu screen.

2. Select

3. Use the pointer button to highlight the new ID, and press

Enter to select it.

4. When you’re done, press

Menu button on the remote control. You see the

Extended, then Projector ID.

Menu to exit.

Presenting With the Remote Control 43

Checking the Projector ID

You can check the projector’s ID by following these steps:

1. Point the remote control at the projector you want to check.

note

If you’re using a remote control ID other than the default ID of zero, you have to set the ID each time you turn on the projector.

note

When the remote control ID switch is in the you can control any projector regardless of the projector or remote control ID settings.

Off position,

2. While holding the

ID button, press the Help button. You see a

message on the screen like this:

Setting the Remote Control ID

The remote control’s default ID is zero. This lets you operate any projector. To set it to operate a specific projector, follow these steps:

1. Move the remote control ID switch to the

2. Press and hold the

ID button on the remote control.

On position.

3. While holding the remote control (0 through 9) to select the desired ID. Select zero to control all projectors, or select a number to match the ID of the projector(s) you want to operate.

44 Presenting With the Remote Control

ID button, press a numbered button on the

Fine-Tuning the Projector

You can use the projector’s on-screen menus to adjust the image,

sound, and other features. This chapter covers the following information:

■ Using the menu system

■ Adjusting the image

■ Adjusting signal settings

■ Customizing projector features

■ Using the projector security features

■ Customizing power and operation

■ Multi-screen color adjustment

■ Projector menu and options list

Using the Menu System

You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps:

1. To display the menu screen, press the remote control or on the projector.

You see a menu screen similar to the one below:

Options

Menu list

Menu button on the

note

For a complete list of menus and options, see page 62. For more information on these menus and options, continue reading this chapter.

46 Fine-Tuning the Projector

The menus are listed on the left and the options available for the highlighted menu are shown on the right.

2. Use the pointer button on the remote control (or the navigational buttons on the projector) to scroll through the menu list. When you’ve highlighted the desired menu, press the

Enter

button to select it.

3. Once you’ve selected the menu, use the pointer button to scroll through the list of options. (Some of the options may be grayed out or unavailable, depending on the selected source.)

4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may

have to press the

Enter button to view a sub-screen for changing

the setting.

■ Press the left or right side of the pointer button to adjust

a slider bar.

■ To select from two or more settings, use the pointer

button to highlight the desired setting and press

Enter.

5. After changing the settings, press the

Esc button to save your

changes and return to the previous menu (or press it repeatedly to exit the menu system).

You can also press the

Menu button to exit.

Restoring the Default Settings

You can use the menu system’s Reset options to restore the factorydefault settings for all the settings listed in a specific menu, or all the settings in all menus.

To restore the settings in a specific menu, open that menu, select

Reset, and confirm as needed. (The example below shows how to

reset the Image menu.)

Reset settings

for current menu

Reset settings for

all menus

note

When you select Reset All in the Reset menu, it does not reset the Input Signal, User’s Logo, Multi-screen, Language, Lamp Hours, or Network settings.

To restore all the projector settings to their factory-default values, select the

Reset menu, highlight Reset All, and press Enter.

Fine-Tuning the Projector 47

Adjusting the Image

You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast.

note

The available settings vary depending on the input source selected.

note

The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select

Brightness Control in the

Settings menu, then choose

High or Low (the default

setting is High).

1. Press the select the

Menu button on the projector or remote control and

Image menu.

You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.)

Computer/RGB Video

Component Video/

Composite Video/

S-Video

2. Use the pointer button to highlight the desired option, then adjust it as needed:

■ Color Mode

Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the

Mode

setting in the Image menu. You can save a different

Color

setting for each source. See page 35 for more information on each color mode.

■ Brightness

Lightens or darkens the overall image.

■ Contrast

Adjusts the difference between light and dark areas.

■ Color Saturation

Adjusts the color depth of the image.

48 Fine-Tuning the Projector

■ Tint

Adjusts the balance of green to magenta in the image.

■ Sharpness

Adjusts the sharpness of the image.

■ Abs. Color Temp.

Sets a color temperature between 5000 and 10000 °K. (Not available if

■ Color Adjustment

sRGB is selected as the Color Mode setting.)

Adjusts the color values. For Customized color mode, select

R, G, B, C, M, Y to adjust individual red, green, blue, cyan,

magenta, and yellow hue, saturation, and brightness values. For other color modes, RGB may be selected to adjust red, green, and blue saturation values. (Not available if

sRGB is

selected as the Color Mode setting.)

Six-Axis Color Adjustment

For special projection material, such as high-quality photographs or artwork, you can adjust the hue, saturation, and brightness for six different color axes.

1. Follow the instructions on page 48 to open the Image menu and

Color Mode.

select

2. Press the

Enter button to select Customized, then press Esc to

return to the Image menu.

3. Select

Color Adjustment and press Enter. You see hue,

saturation, and brightness controls on the screen for six colors:

, B, C, M, Y (red, green, blue, cyan, magenta, and yellow).

4. Select the color axis you want to adjust and press

Enter. You see

color controls for hue, saturation, and brightness.

Hue changes the balance of color, and saturation changes the strength of the color.

5. Use the pointer button to adjust the hue, saturation, and brightness. You see the adjustments reflected on the screen. When you are satisfied with the color, press

Esc.

6. Repeat steps 4 and 5 for each color axis you want to adjust.

Fine-Tuning the Projector 49

You may need to readjust the color as the lamp in your projector changes over time.

Adjusting Signal Settings

Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio to widescreen format for video images.

1. Press the

Menu button and select the Signal menu.

You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.)

Computer/RGB Video

Component Video/S-Video

2. Use the pointer button to highlight the desired option, then adjust it as needed:

■ Auto Setup

Leave this setting

On to automatically optimize computer

images. Turn it off if you want to save adjustments you have made to the Tracking, Sync, and Position settings.

■ Resolution

Set to Auto to have the projector automatically identify the resolution of the input signal. If necessary (because some of the image is missing, for example), adjust to

Normal. You can also select Manual and specify a resolution.

Wide or

50 Fine-Tuning the Projector

■ Tracking

Adjust this value to eliminate vertical stripes in computer images.

■ Sync

Adjust this value if computer images appear blurry or flicker.

■ Position

If the image is slightly cut off on one or more sides, it may not be centered exactly. Select this setting and use the pointer button to center it.

■ Progressive

For composite video, S-video, and component video signals only. Turn this setting on to convert interlaced signals into progressive signals (best for still images). Select viewing general video images. Select

Film/Auto for movie

Video for

images, CG, and animated images. Leave the setting moving images.

■ Noise Reduction

Smooths out rough images. Select your favorite setting. Epson recommends that you select

Off when viewing image

sources with very low noise, such as DVDs.

■ Input Signal

If the colors don’t look right on the Auto setting, select the setting for the type of equipment you’ve connected to the

Computer1 or Computer2 ports. Choose RGB for a

computer or RGB-video connection, and

Component for a

video player that outputs a component video signal (with connectors labeled Y/Cb/Cr or Y/Pb/Pr).

Off for

note

You can also use the remote control’s automatically reset the

and Position settings. See

Auto button to

rojector’s Tracking, Sync,

age 89 for details.

note

The Noise Reduction setting cannot be set for digital RGB signals.

Fine-Tuning the Projector 51

■ Video Signal

Select the setting for the type of equipment you’ve connected

Video1 or Video2 ports. Leave this setting at Auto

to the unless you are using a 60-Hz PAL system (then select

PAL60).

■ Aspect

Sets the image’s aspect ratio (ratio of width to height). Depending on your projector model and input source, you can select

Normal, 4:3, 16:9, or Through; see page 36 for

more information.

Customizing Projector Features

You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features.

■ Keystone

52 Fine-Tuning the Projector

Adjusts the shape of the image if the projector has been tilted upward or placed at an angle to the screen.

H/V-Keystone to correct horizontal and vertical keystone

Select distortion.

Quick Corner to adjust the shape and position of the

Select projected image.

■ Control Panel Lock

Lets you disable all of the buttons on the projector, or all of the buttons except the Ppower button. See page 58 for more information.

■ Pointer Shape

Lets you choose from three pointer shapes. See page 41 for more information.

■ Brightness Control

Lets you select from two levels of brightness. The Low setting reduces power consumption and noise, and extends the lamp’s operating life.

■ Volume

Raises or lowers the volume if you have connected optional external speakers.

■ Remote Receiver

Deactivates the projector’s front and/or back sensors that detect signals from the remote control. Use this setting to prevent use of the remote control or to stop interference from bright fluorescent lights.

note

You can also adjust the volume using the remote control.

■ User Button

You can assign one of the following six menus to the User button:

Multi-screen, or Resolution. By pressing the button, the

Brightness Control, Info, Progressive, Test Pattern,

assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments.

■ Test Pattern

Displays a test pattern for use when adjusting the zoom and focus, and when performing keystone correction.

Fine-Tuning the Projector 53

Using the Projector Security Features

note

To prevent theft, you can also attach a security cable or Kensington security lock to the projector, and use the lens theft deterrent screw (see page 96).

caution

If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. Also, it’s a good idea to write down your password.

To prevent unauthorized use of the projector, you can do the following:

■ Assign a password. You can use the password to prevent the

projector from being turned on, prevent your custom startup screen from being changed, and lock network settings.

■ Create a custom screen that is displayed at startup and/or when

A/V Mute button is pressed. The screen can be locked with a

the password to discourage theft and provides a way to identify the projector should it be stolen. See page 56.

■ Disable the projector’s buttons; this is useful, for example, if

you’re projecting in a classroom and you want to ensure that no one touches the projector’s buttons while you’re using the remote control. See page 58.

Enabling Password Protection

The default setting for the password is 0000. Follow these steps to create a new password:

1. Press the seconds. You see this screen:

Freeze button on the remote control for about five

2. Use the pointer button to select

3. When you see a message asking if you want to change the

54 Fine-Tuning the Projector

password, select

Password and press Enter.

Yes and press Enter.

4. Hold down the Num button on the remote control and use

the numeric keypad to enter a four digit password. (The default setting is 0000.)

5. When you see a confirmation message, reenter the password. Then press the

Menu button to exit the screen.

To set security options, access the Password Protect screen as described on page 54, and then turn on any of the following options:

■ Power On Protect to prevent unauthorized use of the projector.

After the projector is plugged in and turned on, you must enter a password to use the projector. For details, see “Starting the Projector with a Password” below.

■ User’s Logo Protect to prevent your custom screen and display

settings from being changed. None of the User’s Logo features in the Extended menu can be changed when the User’s Logo Protect function is enabled. For details on creating a custom screen, see page 56.

■ Network Protect to lock the Network settings in the menu

system.

Starting the Projector with a Password

When the password function is enabled, you see this screen when you plug in and turn on the projector:

Hold down

note

If you leave the projector

lugged in, the Password Protect Release screen will not appear. It appears only if you unplug and reconnect the power cord.

Hold down the

Num button on the remote control and use the

numeric keypad to enter the four digit password. The password screen closes and projection begins.

Hold down

Fine-Tuning the Projector 55

If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message

locked

and the projector switches to standby mode. Disconnect the

The projector’s operation will be

projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.

When you see the Password screen again, you can try to enter the correct password.

If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it.

If you have forgotten the password, contact Epson with the request code number that appears in the Password screen for assistance. See “Where To Get Help” on page 93.

Creating Your Own Startup Screen

You can transfer any image from your computer or video source to the projector and then use it as your startup screen. You can also use it as the screen displayed when the projector is not receiving a signal or when you press the logo, slogan, photograph, or any other image you want to use.

A/V Mute button. The image can be a company

56 Fine-Tuning the Projector

Capturing the Image

Start by displaying the image you want to use from either a computer or video source, such as a DVD player or digital camera. Then follow these steps to capture the image and transfer it to the projector:

1. Press the

Extended menu, and press Enter.

2. Highlight

Menu button on the remote control, highlight the

User’s Logo and press Enter.

note

When you choose an image

or the user’s logo, it erases any previously used image. You can save an image up to 300 × 400 pixels in size. Once you have saved a new user’s logo, you cannot return to the factory default logo.

3. When you see the message

Logo?

, select Yes and press Enter. A selection box displays over

Choose this image as the User’s

the image.

4. Use the pointer button to select the area of the image you want to use. Then press

5. When you see the message and press

Enter.

Select this image?, highlight Yes

6. Use the arrow buttons to select a zoom factor (display size) and

Enter.

press

7. When the message appears, select

Save this image as the User’s Logo?

Yes and press Enter. Saving the logo may take a

few moments. Do not use your projector, remote control, or video source while the logo is being saved.

8. When you see the message

Completed, press Menu to exit.

Fine-Tuning the Projector 57

Choosing When to Display the Image

After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the

A/V Mute button (see page 39).

note

You can lock these settings to prevent them from being changed without a password (see page 54).

1. Press the

Enter.

2. Select

Menu button, highlight the Extended menu, and press

Display and press Enter.

3. Choose from these display options:

■ Set Display Background to Logo to display your image

when there is no signal.

■ Set Startup Screen to On to display your image when the

projector is warming up.

■ Set A/V Mute to Logo to display your image when you press

A/V Mute button.

the

4. When you’re finished, press

Menu to exit.

Disabling the Projector’s Buttons

When you enable the Control Panel Lock function, you can lock all of the projector’s buttons, or all of the buttons except the Ppower button. The remote control can still be used to operate the projector.

1. Press the

Enter.

Menu button, highlight the Settings menu, and press

2. Select

3. Select

4. Select

5. Press the

To disable the Control Panel Lock function, select Panel Lock menu. Or press and hold the projector’s control panel for 7 seconds. A message is displayed and the lock is released.

58 Fine-Tuning the Projector

Control Panel Lock and press the Enter button.

Full Lock (to lock all projector buttons) or Partial Lock (to

lock all buttons except the

Yes and press Enter to confirm the setting.

Menu button to exit.

Power button) and press Enter.

Off in the Control

Enter button on the

Customizing Power and Operation

You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations.

■ Display

Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display.

■ Closed Caption

Enables or disables closed captions. Select CC1, CC2, or OFF. The captions are not visible when the menu is displayed or when you use EMP Monitor to access the projector through your network.

■ User’s Logo

Create a custom startup screen, as described on page 56.

■ Projection

Select Front (to project from the front of a screen and right side up),

Front/Ceiling (when the projector is mounted upside-down

from the ceiling), transparent screen), or

Rear (to project from behind onto a

Rear/Ceiling (to project from behind onto

a transparent screen when the projector is mounted upside-down from the ceiling).

note

If you hold down the

A/V Mute button on the

remote control for about five seconds, you switch between

Front and Front/Ceiling

or Rear and Rear/Ceiling.

Fine-Tuning the Projector 59

note

If a power outage occurs when Direct Power On is enabled and the power cord is connected, the projector will start when the power is restored.

Do not use the projector at altitudes above 7,500 feet (2,286 meters).

■ Operation

Enable Direct Power On if you want to be able to start the projector when you connect the power cord (without pressing the Ppower button). Enable Sleep Mode if you want the projector to turn off automatically if it is idle (and no signal is received) for 10 minutes (you can adjust the amount of time using the

Mode Timer setting). Enable High Altitude Mode when you are

using the projector above 4,900 feet (1,500 meters).

■ Standby Mode

Select Network On to enable monitoring of the projector over a network when it is in standby mode (the power light is orange).

■ Projector ID

Lets you assign a numeric ID to each projector. When you are using multiple projectors, you can use the ID to select the one you want to operate with the remote control. See page 43 for instructions.

■ Multi-screen

Use this option if you want to color-match two or more projectors that are being used to display images near each other. You can make image adjustments at each of five adjustment levels. First choose an each level:

Color Correct to adjust the balance between red and green, or

Adjustment Level and then adjust the settings for

Brightness Correct to adjust the brightness, and

blue and yellow. See page 61 for more information about multi-screen color adjustment.

Sleep

■ Language

60 Fine-Tuning the Projector

Select from 27 languages to be used for the projector menus.

Multi-screen Color Adjustment

You can match the color of projected images when two or more projectors are being used to display images near each other. For each screen, you can set five levels of brightness and color correction.

1. Before starting, you may want to assign a numeric ID to each projector. This lets you use the remote control to select the projector you want to adjust. See page 43 for instructions.

To match the display colors as closely as possible, make sure that all the projectors are set to the same color mode before starting. See page 48 for instructions.

caution

If you use two or more projectors side-by-side, exhaust from adjacent projectors might cause overheating. Leave at least 2 feet (60 centimeters) of space between projectors.

2. Press the

Menu button on the remote control. You see the

projector’s menu screen.

3. Press the

Enter.

4. Select

5. Start by setting the Then use the lighter one. Press

Menu button, highlight the Extended menu, and press

Multi-screen and press Enter.

Adjustment Level to 1 for two projectors.

Brightness Correct to match the darker projector to

Enter to see the effects of your adjustments.

6. Next, adjust the brightness of Level 5 for the same two projectors. Match the brighter projector to the darker one.

7. Adjust and match the brightness of Levels 2, 3, and 4.

8. Adjust and match the G/R color correction for all levels. Then adjust and match the B/Y correction for all levels.

9. If you are using three or more projectors, repeat steps 5 through 8 to match projector 3 to projector 2, then match projector 4 to projector 3, and so on.

Fine-Tuning the Projector 61

Projector Menu and Options List

The table below summarizes the options you can select based on the projector menu you are viewing. Some options may not be available depending on the input source you are using.

For more information on these menus and options, read this chapter.

Menu Options

Image Color Mode

Brightness Contrast Color Saturation Tint Sharpness Abs. Color Temp. Color Adjustment Reset

Signal Auto Setup

Resolution Tracking Sync. Position Progressive Noise Reduction Input Signal Video Signal Aspect Reset

Settings Keystone

Control Panel Lock Pointer Shape Brightness Control Volume Remote Receiver User Button Test Pattern Reset

62 Fine-Tuning the Projector

Menu Options

Extended Display

Closed Caption User’s Logo Projection Operation Standby Mode Projector ID Multi-screen Language Reset

Network Wired LAN

PJLink Password Web Control Password SNMP Mail AMX Device Discovery Projector Name Reset

Info Lamp Hours

Source Input Signal Resolution Video Signal Refresh Rate Sync Info Status

Reset Reset All

Reset Lamp Hours

Fine-Tuning the Projector 63

64 Fine-Tuning the Projector

Managing Projectors

The software included with your projector lets you monitor and

control your projectors from a remote computer.

First connect and configure each projector you want to monitor. You can connect the projector over a wired network as described in this chapter.

Once you’ve connected the projectors to the network, you can use any of these tools to manage your projectors:

■ Use EMP Monitor (available for Windows

projectors’ status, switch image sources, turn projectors on and off, control basic settings, and register projectors and projector groups. See the EMP Monitor Operation Guide for more information.

only) to see your

■ Use the mail notification function to receive e-mail alerts about

possible problems. See page 67 for more information.

This chapter covers the following information:

■ Connecting your projector to a wired network

■ Using e-mail alerts to warn you of problems

Connecting to a Wired Network

Follow these steps to connect the projector to your network and configure it with an IP address:

1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the

2. Turn on the projector.

LAN port on the projector. See page 23.

note

If you’re a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the

rojectors you’re monitoring.

3. Press the

Network menu, then press Enter. You see the following screen:

4. Choose

Menu button on the remote control, select the

Wired LAN and press Enter.

5. Do one of the following:

■ If your network assigns addresses automatically, turn on the

DHCP setting.

■ If your network does not assign addresses automatically, turn

DHCP and enter the projector’s IP Address, Subnet

off

Mask, and Gateway Address.

To enter numbers, use the pointer button on the remote control to highlight the number you want to input, then press

Enter.

6. When you’re done making all necessary changes, select

Setup complete, and then Yes to confirm that you want to save

the changes. Press

66 Managing Projectors

Menu to exit.

Return,

Using Projector E-mail Alerts

When this feature is enabled, the projector sends you an e-mail alert if it has any problems.

1. Press the

Network menu, then press Enter. You see the following screen:

Menu button on the remote control, select the

note

You can also set e-mail alerts from EMP Monitor (see the

EMP Monitor Operation Guide for more

information).

2. Choose

3. Highlight

4. Enter the IP address for the

Mail, then press Enter.

On to receive e-mail notifications, then press Enter.

SMTP server for the projector.

You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used: 127.x.x.x,

224.0.0.0 to 255.255.255.255 (where x is a number from 0 to

255).

5. Enter the SMTP server’s port number. The default value is 25. You can enter a numeric value from 1 to 65535.

6. Choose one of the

Email Address fields, then enter the e-mail

address where you want to receive a message when a problem occurs. You can register up to three addresses. You can enter up to 32 alphanumeric characters for the e-mail address.

Managing Projectors 67

note

If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message.

If Standby Mode is set to

Network On in the

Extended menu, the projector can still be monitored even if the projector is in standby mode (when the power is off).

7. Select problems or warnings to be notified about by e-mail. (Numbers 1 through 3 in this section correspond to the e-mail addresses you entered.)

8. When you’re done making all necessary changes, select

Setup complete, and then select Yes to confirm that you

select want to save the changes. Press

Menu to exit the menu system.

Return,

When the selected problem or warning occurs, an e-mail message is sent to the specified notification addresses. The subject line of the e-mail is

EPSON Projector. The e-mail includes the following

information:

■ Line 1: The name of the projector where the problem has

occurred

■ Line 2: The IP address of the projector where the problem has

occurred

■ Line 3: Details of the problem

68 Managing Projectors

warning

Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel.

Maintaining the Projector

Your projector needs little maintenance. All you have to do is keep

the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.

The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

■ Cleaning the lens

■ Cleaning the projector case

■ Cleaning the air filter

■ Replacing the air filter

■ Replacing the lamp

■ Replacing the remote control batteries

■ Transporting the projector

Cleaning the Lens

caution

Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged.

caution

Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.

note

To order replacement air filters, request part number V13H134A17. See page 10 for ordering information.

Clean the lens whenever you notice dirt or dust on the surface.

To remove dirt or smears on the lens, use a commercially available cloth for cleaning glasses.

Cleaning the Projector Case

Before you clean the case, turn off the projector and unplug the power cord.

■ To remove dirt or dust, wipe the case with a soft, dry, lint-free

cloth.

■ To remove stubborn dirt or stains, moisten a soft cloth with water

and a neutral detergent and firmly wring the cloth dry. Then wipe the case.

Cleaning the Air Filter

Your projector includes an air filter to ensure the best performance. If dust collects on the air filter (on the side of the projector), clean it as described below. Dust clogs prevent proper ventilation and can cause overheating, which can damage the projector.

Follow these steps:

1. Turn off the projector and unplug the power cord.

2. Grip the air filter cover tab and remove the air filter cover as

70 Maintaining the Projector

shown.

3. Place your finger into the groove and remove the air filter as shown.

4. With the front of the air filter facing down, tap it four or five times to shake off the dust. Turn it over and tap the other side in the same way to shake off the dust.

5. To clean any dust remaining on the air filter, use a small vacuum cleaner designed for computers and other office equipment to clean the front. If you don’t have one, gently clean the vent with a soft brush (such as an artist’s paintbrush).

Maintaining the Projector 71

6. Insert the air filter back into the holes in the cover, then press it firmly into place.

7. Slide the air filter cover in until you feel resistance.

8. If the dirt is difficult to remove or the filter is broken, replace the filter as described on page 73. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new filter.

72 Maintaining the Projector

Replacing the Air Filter

Follow these steps to replace the air filter:

1. Grip the air filter cover tab and remove the air filter cover as shown.

2. Place your finger into the groove and remove the air filter as shown.

Maintaining the Projector 73

3. Insert the new air filter into the holes in the cover, then press it firmly into place.

4. Slide the air filter cover in until you feel resistance.

note

Turn off this product when not in use to prolong the life of the projector.

74 Maintaining the Projector

Replacing the Lamp

The life span of the projection lamp is about 2000 hours if

Brightness Control in the Settings menu is set to High (default), and

3000 hours if See page 78 to check the lamp usage.

It is time to replace the lamp when:

■ The projected image gets darker or starts to deteriorate.

■ The message Replace the lamp appears on the screen when the

lamp comes on and the maintain projector brightness and image quality, replace the lamp as soon as possible.

Brightness Control is set to Low.

Lamp light flashes orange. To

You may also need to replace the lamp if the Lamp light flashes red. See page 83.

Lamp light

Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766). Request part number V13H010L47.

Follow these steps to replace the lamp:

1. Turn off the projector and, after the projector beeps twice, unplug the power cord.

2. Let the projector cool for at least an hour (if it has been on). The lamp is extremely hot immediately after use.

3. Loosen the lamp cover screws (you don’t need to remove them). Then remove the lamp cover.

warning

Let the lamp cool fully before replacing it.

In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury. If the projector has been installed on the ceiling, you should stand to the side of the lamp cover, not underneath it.

If the lamp is used after the replacement period has passed, the possibility that the lamp may break increases. When a lamp replacement message appears, replace the lamp with a new one as soon as possible, even if it is still working.

note

Even when the lamp cover is removed, it is still attached to the projector to prevent it from falling when the projector is mounted on the ceiling.

Maintaining the Projector 75

note

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

4. Loosen the two screws holding the lamp in place (you can’t remove them).

Loosen, but don’t remove these screws

5. Hold the lamp as shown and pull it straight out.

6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is

7. Once the lamp is fully inserted, tighten its screws.

76 Maintaining the Projector

facing the right way.)

8. Replace the lamp cover, then tighten its screws.

9. Reset the lamp timer as described in the next section.

Resetting the Lamp Timer

After you replace the lamp, you need to reset the lamp timer using the projector’s menu.

1. Press the

Menu button on the remote control or on the

projector’s control panel. You see the main menu.

2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight

Reset, then press Enter.

You see this screen:

3. Select

4. When you see the prompt, select

5. When you’re finished, press

Reset Lamp Hours and press Enter.

Yes and press Enter.

Menu to exit.

Maintaining the Projector 77

note

The information displayed depends on the input signal currently selected.

Checking Lamp Usage

To check the number of hours the lamp has been used, press the

Menu button and highlight the Info menu. You see a screen like this:

caution

When replacing batteries, take the following precautions:

■ Replace the batteries as

soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

■ Do not expose batteries to

heat or flame.

■ Dispose of used batteries

according to local regulations.

■ Do not use batteries other

than those specified in this User’s Guide and do not use batteries of different types or mix old and new batteries.

■ Keep these batteries out of

the reach of children. Batteries are choking hazards and are very dangerous if swallowed.

The life span of the lamp is about 2000 hours if the

Control setting in the Settings menu is set to High (default), and

3000 hours if the

Brightness Control setting is set to Low. Make

Brightness

sure you have a spare lamp handy if the usage hours on this menu are close to the life span of your lamp.

Replacing the Batteries

Replace the batteries in the remote control as described below:

1. Turn the remote control over.

2. Press down on the tab on the battery cover as you lift the cover off.

78 Maintaining the Projector

3. Install two AA alkaline batteries, inserting the

+ and – ends as

shown.

4. Position the cover as shown, then press down until it snaps into place.

Transporting the Projector

The projector contains many glass and precision parts. Follow these guidelines to prevent damage:

■ When shipping the projector for repairs, use the original

packaging material if possible, including the protective lens pads. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.

■ When transporting the projector a long distance, first place it in a

hard-shell shipping case, then pack it in a firm box with cushioning around the case.

■ Attach the lens cover to the lens.

■ Return the projector feet to their stored (highest) positions.

■ Turn the vertical lens shift dial so that the lens is in its lowest

position.

note

Epson shall not be liable for any damages incurred during transportation.

Maintaining the Projector 79

80 Maintaining the Projector

Solving Problems

This chapter helps you solve problems with your projector, and tells

you how to contact technical support for problems you can’t solve yourself. The following information is included:

■ Using the projector’s on-screen help system

■ What to do when the projector’s status lights flash

■ Solving projector operation problems

■ Solving problems with the image or sound

■ Solving network problems

■ Solving problems with the remote control

■ Contacting technical support

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can get help by pressing the on the remote control.

? Help button on the back of the projector or

1. Press the projector.

You see the Help menu:

2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items.

? Help button on the remote control or on the

82 Solving Problems

3. Press the to select the menu item.

4. To exit the help system, press the

If none of the suggestions solve your problem, see additional solutions to problems in the following sections.

Enter button on the remote control or on the projector

? Help button.

Checking Projector Status

If your projector isn’t working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status.

Lamp light

Power light

Temperature light

Refer to the following table for a complete description of the projector’s status lights:

Status lights

Light Status Description

Orange The projector is in sleep or standby mode. You can unplug it or press the

P power button to turn it on.

Flashing green The projector is warming up. Wait for the image to appear.

Green The projector is operating normally.

Flashing orange The projector is cooling down. You can’t turn it back on (and you should

not unplug it) until the light stops flashing and remains orange.

The projector is setting itself up for network monitoring.

Red or flashing red

There is a problem with the projector. Check the other two lights and the information on page 84 to diagnose the problem.

Solving Problems 83

Status lights (continued)

Light Status Description

Flashing orange It’s time to replace the lamp. See page 74 for instructions. If you continue

to use the lamp after the replacement warning, there is an increased possibility that the lamp may break.

Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition,

projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filter and vents are clear.

Red The projector is overheating, which turns the lamp off automatically.

Wait until the projector switches to standby mode (about 5 minutes). Make sure the room temperature is not above 95 °F (35 °C), and there is plenty of space around and under the projector for ventilation.

The air filter may be clogged. Clean or replace the air filter as described on pages 70 to 74.

If you’re using the projector above an altitude of 4,900 feet (1,500 meters), turn on High Altitude Mode in the Operation menu (see page 60).

If the projector continues to overheat after you clean the air filter, the problem may be caused by damage to the cooling fan or temperature sensor. Contact Epson for help as described on page 93.

Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.

Flashing red Power is cut off because of an internal problem. Unplug the power cord

and contact Epson for help, as described on page 93.

Flashing red There is a problem with the fan or temperature sensor. Stop using the

projector, disconnect the power cord, and contact Epson as described on page 93.

Flashing red The lamp may be burnt out. First make sure the lamp cover is securely

installed. If that’s not the problem, the air filter may be clogged. Clean or replace the air filter as described on pages 70 to 74.

If this does not resolve the problem, let the lamp cool and then remove it. If the lamp is cracked, replace it as described on page 74. If the lamp is not cracked, reinstall it. If reinstalling doesn’t work, replace the lamp.

If you’re using the projector above an altitude of 4,900 feet (1,500 meters), turn on High Altitude Mode in the Operation menu (see page 60).

If none of these suggestions resolves the problem, contact Epson as described on page 93.

84 Solving Problems

Solving Projector Operation Problems

The power doesn’t turn on.

■ If the projector doesn’t turn on when you press the Ppower

button, make sure the power cord is connected to the projector and plugged into a working electrical outlet.

■ The power cord may be defective. Disconnect the cord from the

outlet and contact Epson as described on page 93.

■ If the Direct Power On function is enabled and you immediately

plug the power cord back in after unplugging it, the power may not turn back on. Press the Ppower button to turn the projector back on.

The buttons on the projector don’t work.

If the Control Panel Lock function has been enabled, you can’t use the buttons on the projector. Try using the remote control instead (make sure it is set to the correct ID). See page 58 for information about the Control Panel Lock function.

Solving Problems With the Image or Sound

No image appears on the screen.

■ Check that the Ppower light is green, not flashing.

■ The projector may be in standby or sleep mode. If the Ppower

light is orange, press the Ppower button to turn the projector on.

■ If the power was switched off and then on again, the projector

may be cooling down. Wait until the Ppower light stops flashing and remains orange; then press the Ppower button again.

■ Press the A/V Mute button on the remote control to make sure

the picture has not been turned off temporarily.

Solving Problems 85

■ The attached computer may be in sleep mode or displaying a

black screen saver. Try pressing a key on the computer.

■ If you are projecting from a DVD player or other video source,

make sure you turn it on and press its

■ If you are projecting from a video source, make sure the Video

Play button.

Signal setting is correct (see page 50).

■ You can also try resetting all of the configuration menu settings.

See page 47.

You’ve connected a computer and see a blue screen with the message No Signal displayed.

■ Make sure the cables are connected correctly, as described on

page 15.

■ If you’ve connected a computer and one or more video sources,

you may need to press the projector or one of the source buttons on the remote control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.

Source Search button on the

86 Solving Problems

■ Make sure the power for your connected equipment is turned on.

If you’re using a PC notebook:

■ Hold down the Fn key on the keyboard and press the function

key that lets you display on an external monitor. It may have an icon such as , or it may be labelled

CRT/LCD. Allow a few

seconds for the projector to sync up after pressing it. Check your notebook’s manual or online help for details.

On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.

If you connect the notebook while the projector or computer are already turned on, the function

Fn key that changes the

computer’s image signal to external output may not work. Turn the computer and the projector off and then back on.

■ Depending on your computer’s video card, you might need to use

the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details.

If you’re using Mac OS X:

1. Open

2. Click

3. Click

4. Make sure the

5. Click the

6. Make sure the

System Preferences.

Displays.

Detect Displays.

VGA Display or Color LCD dialog box is selected.

Arrangement or Arrange tab.

Mirror Displays checkbox is selected.

The message Not Supported is displayed.

■ Make sure the correct input signal is selected in the Signal menu

(see page 50).

■ Make sure your computer’s resolution and frequency or refresh

rate is supported by the projector (see page 101). If necessary, change your computer’s settings.

Only part of the computer image is displayed.

■ Press the Auto button on the remote control or the Enter button

on the projector.

■ Make sure the image Position setting is correct in the Signal

menu. See page 51 for more information.

■ Press the Aspect button on the remote control.

■ Press the Esc button on the remote control to cancel the E-Zoom

function.

■ Make sure your computer’s resolution setting is correct. See the

compatible video formats listed on page 101.

Solving Problems 87

■ You also may need to modify existing presentation files if you

created them for a different resolution. See your software documentation for specific information.

■ If you’re projecting a wide panel computer image, adjust the

Resolution setting (see page 50).

■ If you’re projecting an image from a computer with dual display

activated, turn dual display off.

The image isn’t square, but keystone-shaped.

If the image isn’t square or rectangular, adjust its shape as described on page 33.

The image contains static or noise.

■ If you’re using a computer cable longer than 6 feet (1.8 meters),

or an extension cable, the image quality may be reduced.

■ Keep your computer and video cables away from the power cord

as much as possible to prevent interference.

■ The video signal may be split between the computer and the

projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display.

88 Solving Problems

■ Make sure the correct input signal is selected in the Signal menu

(see page 51).

■ If you’ve used the Quick Corner or Keystone adjustment, you

may need to decrease the

Sharpness setting in the Image menu

(see page 49).

■ If you’re projecting from a computer, make sure its signal is

compatible with the projector. See page 101.

The image is blurry.

■ There may be dirt or smears on the lens. Clean the lens as

described on page 70.

■ Adjust the focus using the focus ring (see page 32).

■ If the projector is angled sharply toward the screen, it may not be

possible to focus the entire image. Move the projector to position it more directly in front of the screen.

■ Lower the projection angle to reduce the amount of keystone

correction required.

■ Make sure the projector is within the proper range (projection

distance) from the screen (see page 99).

■ Make sure the lens is not fogged by condensation. You may need

to wait before using the projector after moving it from a cold environment to a warm environment.

■ If you’re projecting from a computer, you may need to adjust the

tracking and sync settings as described in the next section.

You see vertical bands or the image still looks blurry after trying the solutions in the previous section.

■ If you’re projecting from a computer and displaying an image that

contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the button on the remote control or the

Enter button on the

Auto

projector to reset the projector’s Tracking, Sync, and Position settings.

■ If further adjustment is needed, you can fine-tune the Tracking

and

Sync settings manually using the Signal menu, as described

on page 51.

1. Fill the screen with an image containing fine detail, such as a pattern to appear as your desktop background, or try projecting black text on a white background.

2. Adjust the

Tracking to eliminate vertical bands.

note

You must be projecting an image for the to have any effect. It works only with computer images projected through the VGA port.

Auto button

Solving Problems 89

3. Adjust the

Sync setting to increase the image sharpness.

note

Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor.

The image is too light or dark, or colors are incorrect.

■ Use the Color Mode option in the projector’s Image menu to

adjust the color (see page 48).

■ If you’re displaying video, adjust the Color Adjustment and

Color Mode settings on the Image menu. You can also try

adjusting the settings on the Image menu.

■ Try adjusting the Brightness and Contrast settings on the Image

menu.

■ Try adjusting the Brightness Control setting (see page 52).

■ Check your computer display settings to correct the color balance.

■ The projector’s lamp may need to be replaced. See page 74 for

instructions.

■ Make sure the correct input signal is selected in the Signal menu

(see page 51).

■ Make sure that all cables are connected to the proper ports and

connected securely.

Color Saturation, ABS Color Temp, and Tint

90 Solving Problems

There is no sound, or the sound is not loud enough.

■ In order to play sound, you must connect optional external

speakers (see page 21).

■ Use the Volume buttons on the remote control to adjust the

volume, or adjust the (see page 53).

■ Make sure A/V Mute is not enabled. (The A/V Mute button may

have been pressed.)

Volume setting in the Settings menu

■ If your presentation includes computer audio, make sure the

volume control on your computer is not turned all the way down or muted. In Windows, you may be able to check this by clicking the volume control in your Windows system tray (lower right

corner of the screen). On a Mac

, you may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.

■ If you’re using a DVD player or other video source, make sure the

cables are connected correctly, as described on page 21.

■ If you’re using a computer audio cable, make sure it is connected

to your computer’s headphone jack or audio out jack. Connect the other end to the projector’s

Audio port (beneath the

Computer2 port) when the computer’s video cable is connected

Computer1 or Computer2 ports.

to the

Solving Network Problems

The projector does not send e-mail alerts even though the e-mail notification function has been turned on.

■ Make sure the mail notification function is set correctly in the

configuration menu. See page 67.

■ Set Standby Mode to Network On in the Extended menu.

Otherwise, the projector cannot send e-mails when it is in Standby mode (when the power is off).

■ If a critical problem develops with a projector which causes it to

suddenly stop working, it may not be possible for the projector to send a message.

■ Make sure the projector is plugged in.

■ Make sure the LAN cable is connected correctly. Reconnect it if it

is not connected or it is not connected correctly (see page 23).

For problems with EMP Monitor, see the EMP Monitor Operation

Guide.

Solving Problems 91

Solving Problems With the Remote Control

The projector doesn’t respond to remote control commands.

■ Point the remote control towards the receiver.

■ Make sure the projector and remote control IDs match. To

operate all projectors by remote control regardless of ID settings, set the ID switch on the side of the remote control to

■ The remote control’s batteries may not be installed correctly or

may be low on power. To change the batteries, see page 78.

■ Make sure you are within about 49 feet (15 meters) of the

projector and within range of the projector’s front or back sensor.

■ Dim the room lights and turn off any fluorescent lights. Make

sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector’s infrared receivers. Also, turn off any nearby equipment that emits infrared energy, such as a radiant room heater. If necessary, use the

Remote Receiver setting to disable the projector’s front or back

sensor if it continues to pick up interference (see page 53).

Off.

92 Solving Problems

■ Make sure the Remote Receiver setting isn’t disabling both of

the projector’s sensors (see page 53).

■ If any buttons are held for longer than 30 seconds, the remote

enters sleep mode. Release any button that is held to wake the remote.

■ When the optional remote control cable is connected, the remote

control light-emitting area and the projector’s remote receiver are disabled. If you’re not using the cable, make sure it is disconnected from both the remote control and the projector.

Where To Get Help

Epson provides these technical support services:

Internet Support

Visit Epson’s support website for solutions to common problems with the PowerLite G5000. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 Friday, for the duration of your warranty period.

You may also speak with a projector support specialist by dialing one of these numbers:

■ U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday

through Friday.

AM to 6 PM, Pacific Time, Monday through

■ Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday

through Friday.

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Solving Problems 93

Before you call for support, please have the following information ready:

■ Product name (PowerLite G5000)

■ Product serial number (located on the projector)

■ Proof of purchase (such as a store receipt) and date of purchase

■ Computer or video configuration

■ Description of the problem

Purchase Supplies and Accessories

You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca

(Canadian sales).

94 Solving Problems

Projector Installation

This appendix provides guidelines on installing the projector in a

permanent location, such as a theater or conference room.

Installation Guidelines

The projector can be installed for four different viewing setups: front projection, ceiling projection, rear projection onto a semi-transparent screen, or rear/ceiling projection, as shown:

Front projection Rear projection

Rear/ceiling projectionCeiling projection

To project from overhead, you’ll need the optional ceiling mounting hardware (see page 10). You’ll also need to select the appropriate

Projection setting in the projector’s Extended menu to flip the image

upside-down (see page 59).

If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the image using the projector’s

Keystone functions, as described on page 33.

Quick Corner and/or

Security Features

The projector includes security features to prevent its theft when installed or used in public locations:

■ Security cable attachment. You can attach a commercially

available security cable as shown below to secure the projector to a table or ceiling mount.

96 Projector Installation

Security cable attachment

■ Kensington security slot. The security slot (located above the

power inlet) is compatible with the MicroSaver security systems manufactured by Kensington. You can purchase this lock from Epson (see page 10).

■ Lens theft deterrent screw. You can lock the lens with the

supplied screw, so that the lens cannot be removed.

In addition, the projector includes several menu-operated security features (see page 54).

Installing and Removing the Lens

See the following sections for instructions on removing and installing the lens.

Removing the Lens

1. Turn off the projector and unplug the power cord.

2. If you’ve attached the lens theft deterrent screw, remove it (see the previous section).

3. Hold down the lens removal button and turn the lens counterclockwise until you hear it click.

4. Remove the lens by pulling it straight out.

note

You do not need to remove the lens when you transport the projector. For transportation instructions, see page 79.

Projector Installation 97

caution

Only install or remove the lens when necessary. If dust enters the projector, projection quality may deteriorate and/or the projector may malfunction.

Do not install or remove the lens when the projector’s lens insertion section is facing up. Dust could enter the projector.

Do not touch the lens with your hand or fingers. If fingerprints or oils are left on the surface of the lens, projection quality will deteriorate.

Installing the Lens

1. Turn off the projector and unplug the power cord.

2. Turn the focus ring clockwise until it stops moving.

3. Make sure the white dot on the lens is facing up. Insert the lens straight into the projector, then turn clockwise until you hear it click into place.

White dot

98 Projector Installation

4. If necessary, attach the lens theft deterrent screw (see page 97).

Technical Specifications

General

Type of display Epson poly-silicon TFT active matrix

Resolution (native format) 1024 × 768 pixels (XGA)

Color reproduction 16.8 million colors

Brightness High mode:

White light output 4000 lumens (ISO 21118 standard) Color light output 4000 lumens

Low mode: White light output 3200 lumens (ISO 21118 standard) Color light output 3200 lumens

Contrast ratio 1000:1

Image size 30 to 300 inches (76.2 to 762

centimeters)

Projection distance 2.7 to 47.8 feet (0.8 to 14.6 meters)

Projection methods Front, rear, upside-down (ceiling

mount)

Optical aspect ratio 4:3 (horizontal:vertical)

Zoom ratio 1:1.8

Noise level 29 dB in Low Brightness mode

35 dB in High Brightness mode

Keystone correction

Mouse compatibility Requires optional Wireless IR Mouse

±40° vertical, ±20° horizontal

Receiver (part number V12H007T16)

note

Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.

Turn off this product when not in use to prolong the life of the projector.

Projection Lamp

Type UHE (Ultra High Efficiency)

Power consumption 210 W

Lamp life Approx. 2000 hours (High Brightness

mode) Approx. 3000 hours (Low Brightness

mode)

Part number V13H010L47

Remote Control

Range 49.2 feet (15 meters)

Batteries (2) Alkaline AA

Dimensions

Height 5.3 inches (135 mm), feet retracted

Width 18.5 inches (470 mm)

Depth 13.3 inches (336.8 mm), without lens

Weight 14.5 lb (6.6 kg)

100 Technical Specifications

Electrical

Rated frequency 50/60 Hz AC

Power supply 100/240 VAC, 3.8A/1.7 A

Power consumption Operating:

100 to 120 VAC, 343 W 220 to 240 VAC, 327 W Standby: 100 to 120 VAC, 0.4 W (network off) 10 W (network on) 220 to 240 VAC, 0.6 W (network off) 12 W (network on)

Epson PowerLite G5000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Important Safety Information

Copyright Notice

Trademarks

Contents

Welcome

Using Your Documentation

Getting More Information

Registration and Warranty

Optional Accessories

Setting Up the Projector

Unpacking the Projector

Additional Components

Positioning the Projector

Connecting to a Computer

Connecting to Video Equipment

Connecting a Composite Video Source

Connecting an S-Video Source

Connecting a Component Video Source

Connecting an RGB Video Source

Playing Sound

Connecting a Network Cable

Turning the Projector On and Off

Using the Direct Power On Function

Shutting Down the Projector

Displaying and Adjusting the Image

Displaying an Image

Troubleshooting Display Problems

You Can’t Project an Image

The Projector and Notebook Don’t Display the Same Image

Adjusting the Image

Adjusting the Position of the Image

Focusing and Zooming the Image

Adjusting the Image Shape

Selecting the Color Mode

Resizing Video Images

Presenting With the Remote Control

Using the Remote Control

Controlling the Picture and Sound

Switching Between Picture Sources

Turning Off the Picture and Sound

Stopping Action

Zooming Part of Your Image

Controlling the Volume

Highlighting Your Presentation

Using the Pointer Tool

Choosing a Different Pointer Shape

Operating Your Computer With the Remote Control

Operating Two or More Projectors With the Remote Control

Setting the Projector ID

Checking the Projector ID

Setting the Remote Control ID

Fine-Tuning the Projector

Using the Menu System

Restoring the Default Settings

Adjusting the Image

Six-Axis Color Adjustment

Adjusting Signal Settings

Customizing Projector Features

Using the Projector Security Features

Enabling Password Protection

Creating Your Own Startup Screen

Disabling the Projector’s Buttons

Customizing Power and Operation

Multi-screen Color Adjustment

Projector Menu and Options List

Managing Projectors

Connecting to a Wired Network

Using Projector E-mail Alerts

Maintaining the Projector

Cleaning the Lens

Cleaning the Projector Case

Cleaning the Air Filter

Replacing the Air Filter

Replacing the Lamp

Resetting the Lamp Timer

Checking Lamp Usage