Epson PowerLite 822+, PowerLite 83+ User's Guide
PowerLite® 822+/83+
Multimedia Projector
User’s Guide
Important Safety Information
WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Trademarks
Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision is a trademark of Seiko Epson
Corporation.
PowerLite and PrivateLine are registered trademarks; Duet and SizeWise are trademarks; and Epson Store and
Extra Care are service marks of Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
The contents of this manual are subject to change without notice.
© 2007 Epson America, Inc. 12/07
2
Contents
C
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting Up the Projector . . . . . . . . . . . . . . . . . . . . 15
1
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting with the VGA Cable . . . . . . . . . . . . . . . . . 18
Connecting with a VGA-5BNC Cable. . . . . . . . . . . . . 20
Connecting an External Monitor . . . . . . . . . . . . . . . . . 21
Playing Sound Through the Projector . . . . . . . . . . . . . 22
Connecting External Speakers . . . . . . . . . . . . . . . . . . . 23
Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting a Composite Video Source . . . . . . . . . . . . 25
Connecting an S-Video Source . . . . . . . . . . . . . . . . . . 26
Connecting an RGB Video Source. . . . . . . . . . . . . . . . 27
Connecting a Component Video Source . . . . . . . . . . . 28
Playing Sound Through the Projector . . . . . . . . . . . . . 29
3
2
3
Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 34
Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 34
Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 36
What To Do If You See a Blank Screen . . . . . . . . . . . . . 36
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Focusing and Zooming Your Image. . . . . . . . . . . . . . . . 38
Adjusting the Height of Your Image . . . . . . . . . . . . . . . 39
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 40
Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 40
Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 41
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the Remote Control . . . . . . . . . . . . . . . . . . . 43
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 44
Switching Between Picture Sources . . . . . . . . . . . . . . . . 44
Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 45
Turning Off the Picture and Sound. . . . . . . . . . . . . . . . 46
Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Changing the Image’s Aspect Ratio . . . . . . . . . . . . . . . . 47
Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 49
4
4
Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 50
Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 51
Adjusting Colors and Clarity . . . . . . . . . . . . . . . . . . . . . . . . 52
Adjusting the Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 56
Selecting Projector Setup Options . . . . . . . . . . . . . . . . . . . . 58
Selecting Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 60
Viewing Lamp Usage and Other Information. . . . . . . . . . . . 61
5
6
Using the Projector’s Security Features. . . . . . . . . . . . . . . . . 62
Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . 64
Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Turning On the Password and User’s Logo . . . . . . . . . . 66
Starting the Projector with a Password. . . . . . . . . . . . . . 67
Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . 68
Installing Security Locks . . . . . . . . . . . . . . . . . . . . . . . . 68
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . . 69
Maintenance and Transportation . . . . . . . . . . 71
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 72
Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . 72
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Transporting the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . 78
Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Using On-Screen Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
What To Do When the Lights Flash . . . . . . . . . . . . . . . . . . 80
Solving Problems with the Image or Sound . . . . . . . . . . . . . 82
Solving Password Problems . . . . . . . . . . . . . . . . . . . . . . . . . 87
Solving Problems with the Remote Control . . . . . . . . . . . . . 88
Solving Network Problems. . . . . . . . . . . . . . . . . . . . . . . . . . 89
Where To Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Speak to a Support Representative. . . . . . . . . . . . . . . . . 90
7
Monitoring the Projector Over a Network. . 91
Installing the Network Software. . . . . . . . . . . . . . . . . . . . . . 92
Windows System Requirements . . . . . . . . . . . . . . . . . . 92
Installing the Software on a Windows System . . . . . . . . 92
Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . 93
Selecting Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 94
Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . 95
5
A
B
Using EMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Opening and Closing EMP Monitor . . . . . . . . . . . . . . . 96
Registering a Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Monitoring Your Projector . . . . . . . . . . . . . . . . . . . . . . 97
Using E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Using a Browser to Monitor the Projector . . . . . . . . . . . . . 101
Technical Specifications . . . . . . . . . . . . . . . . . . . . 103
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Safety and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . 106
Compatible Computer Display Formats. . . . . . . . . . . . . . . 107
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 111
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 113
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
6
-
Welcome
W
The PowerLite
than 7 pounds. The projector offers 2600 ANSI lumens (822+) or
2200 ANSI lumens (83+) of brightness. From classrooms to
boardrooms, your full-color presentations and videos will be bright
and vibrant even in ordinary indoor lighting.
Images are displayed at a native resolution of 1024 × 768 pixels.
®
Epson
saturation, even in well-lit rooms.
You can connect the projector to a wide range of computers, including
IBM
and Intel
many iMac
SizeWise
ranging from VGA through UXGA.
3LCD technology ensures accurate color and remarkable
®
-compatible PCs and laptops, Apple® Macintosh,® PowerPC®
®
Core™ Macintosh computers, PowerBook® computers, and
®
and iBook® series systems. With Epson’s patented
™
technology, the projector supports computer displays
®
822+/83+ is a portable projector that weighs less
You can use any of the following video sources: HDTV, VCR, DVD
player, gaming console (such as Microsoft
PlayStation
The projector supports NTSC, PAL, and SECAM video formats.
You can also connect the projector to a LAN (local area network) so
you can monitor the projector from a remote network computer using
the included EMP Monitor software.
You can connect up to four devices to the projector at the same time.
With the projector’s
identify your input source. Just press the button until you see the
image you want on the screen.
®
3, and Nintendo Wii™), camcorder, or digital camera.
Source Search button, you don’t even have to
®
Xbox,™ Sony®
7
To prevent unauthorized use of the projector, you can assign a
password, create a user logo which is displayed at startup to identify
the projector, and disable the projector’s buttons through a full or
partial Operation Lock feature. For more information about security
features, see page 62.
Getting the Most from Your Projector
Depending on your presentation, you can take advantage of any or all
of these options:
■ Connecting to a laptop or other computer
If you want to connect the projector to a laptop or desktop
computer, see page 18. For additional presentation control, you
can connect an external monitor to view the presentation on your
computer simultaneously.
■ Connecting to video sources
You can connect a DVD player, VCR, HDTV, camcorder, digital
camera, and other video sources to your projector. See page 24 for
instructions.
8 Welcome
■ Using the remote control
The remote control lets you switch from computer to video
sources, zoom in on part of your image, freeze or mute the
presentation, and adjust many other projector features. For
details, see Chapter 3.
■ Enhancing sound in your presentation
By connecting your projector to external speakers, you can
enhance the audio impact of your presentations.
Using Your Documentation
In addition to this manual, your documentation includes a Quick
Setup sheet, warranty brochures, and an Epson PrivateLine
®
Support
card.
The Quick Setup sheet gives instructions to quickly set up your
projector and connect it to a computer or video device.
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■ Warnings must be followed carefully to avoid bodily injury.
■ Cautions must be observed to avoid damage to your equipment.
■ Notes contain important information about your projector.
Getting More Information
Need tips on giving presentations? How about quick steps for setting
up your projector? Here’s where you can look for help:
■ www.presentersonline.com
Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art, and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club—and it’s free.
note
The instructions here apply
to the PowerLite 822+ and
PowerLite 83+ projectors
and cover both projectors,
unless noted.
■ Built-in help system
Press the Help button on the remote control or projector to get
quick solutions for common problems. See page 80 for details.
■ epson.com/support
Download FAQs (frequently asked questions) and e-mail your
questions to Epson support on the PowerLite 822+ or
PowerLite 83+.
If you still need help after checking this User’s Guide and the sources
listed above, you can use the Epson PrivateLine Support service to get
help fast. Call (800) 637-7661 and enter the PIN on your PrivateLine
Support card. See page 89 for more information.
Welcome 9
Registration and Warranty
Your projector comes with a basic carry-in warranty and an
international warranty that let you project with confidence anywhere
in the world. For details, see the warranty brochures that came with
your projector.
In addition, Epson offers Extra Care
charge. In the unlikely event of an equipment failure, you won’t have
to wait for your unit to be repaired. Instead, Epson will ship you a
replacement unit anywhere in the United States or Canada, usually
within one business day. See the Extra Care Road Service brochure for
details.
To register, complete the registration form that came with your
projector and mail it to Epson. Or register your product online using
your projector CD, or at:
http://www.epson.com/webreg
Registering also lets you receive special updates on new accessories,
products, and services.
SM
Road Service at no additional
10 Welcome
Unpacking the Projector
After unpacking the projector, make sure you have all these items:
Projector
VGA computer cable Power cord
PDF User's Guide
CD-ROM
Remote control
and batteries
Password Protected
Sticker
Projector software
CD-ROM
Save all packaging in case you need to ship the projector. Always use
the original packaging (or equivalent) when you send the projector to
another location. See page 78 for transportation instructions.
Welcome 11
Projector Parts
Front
Control panel
Lamp cover
Security slot
A/V mute
slide lever
Zoom ring
Air exhaust
vent
Back
Remote
control sensor
Speaker
Audio Out
port
Bottom
S-Video port
Video portLAN port
Monitor Out port
(for Computer1
port output only)
Front adjustable
foot
Audio L-R
input ports
A/V mute
slide
Foot release lever
Computer 1 and 2
(Component Video) ports
Power
inlet
RS-232C
serial port
Focus ring
Remote control
sensor
Audio 1 and 2
input ports
Rear adjustable
foot
12 Welcome
Holes for
ceiling
mount
bracket
Security
lock slot
Air
filter
Hole for
ceiling
mount
bracket
Control Panel
Turns projector
on and off
Indicate
projector
status
Opens menu system
Up/down arrows and
keystone correction
Cancel/exit
Opens help
system
Searches for
source image
Left/right arrows
and
Volume down/up
Automatically
adjusts computer
images
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
■ To receive an S-Video signal, you need an S-Video cable. One is
usually provided with your video device or you can purchase it
from Epson. See page 14.
■ To receive a component video signal from a VCR or other video
device, you need a D-sub, 15-pin, component-to-VGA video
cable, which is available from Epson. See page 14.
■ Some older PowerBooks and Macintosh desktop models may
need a Macintosh video adapter; see your computer dealer. Older
iMac systems may need a special adapter to provide a VGA output
port; see your computer dealer.
■ To receive an audio signal, you need a commercially available
audio cable; see your computer or electronics dealer.
Welcome 13
note
To purchase a replacement
remote control, call
(562) 276-4394 (U.S.) or
(905) 709-3839 (for dealer
referral in Canada).
Optional Accessories
To enhance your use of the projector, Epson provides the following
optional accessories:
Product Product number
Replacement lamp V13H010L42
Air filter set (includes 2 filters) V13H134A13
Component-to-VGA video cable
S-Video cable
Distribution amplifier ELPDA01
50-inch portable screen (4:3 aspect ratio)
60-inch portable pop-up screen (4:3 aspect ratio)
80-inch portable pop-up screen (4:3 aspect ratio)
83.6-inch hanging pull-down screen
(4:3 aspect ratio)
™
Ultra Portable Projector screen
Duet
(4:3 and 16:9 aspect ratio)
ELPDC05 high resolution document imager V12H162020
Kensington® security lock ELPSL01
Ceiling mount (gyro lock with suspension adapter)
False ceiling plate
Suspension adapter
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel
ELPKC19
ELPSV01
ELPSC06
ELPSC07
ELPSC08
ELPSC09
ELPSC80
ELPMBUNI
ELPMBFCP
ELPMBAPL
ELPMBSEC
ELPMBACC
14 Welcome
You can purchase screens, carrying cases, or other accessories from an
Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Setting Up the Projector
1
This chapter tells you how to set up the projector and connect it to a
computer or video source. You can connect up to four devices
simultaneously: four video sources, or two computer and two video
sources.
You’ll find instructions for the following in this chapter:
■ Positioning the projector
■ Connecting to a computer
■ Connecting to video sources
1
15
note
You can download the
Projection Distance
Calculator program from
the Drivers and Downloads
section of Epson’s web site:
www.epson.com/support
Positioning the Projector
Before connecting the projector, you
need to decide where to place it. If
you’re setting up the projector yourself
and it isn’t already installed in the
room you’re using, you’ll probably
want to place it on a table in front of
the screen, as shown.
This lets you stand in the front of the room, face the audience, and
remain close enough to the equipment to be able to control it. Try to
leave as much space as possible between the projector and the screen to
get a good-size image.
Place the projector somewhere between 3 and 30 feet from the screen.
Use the figure below to help you determine exactly how far. Image size
increases with distance, but can vary depending on how you’ve
adjusted the optical zoom and other settings.
28 to 34 ft (4:3)
31 ft (16:9; wide only)
16 Setting Up the Projector
5.6 to 6.8 ft (4:3)
6.1 to 7.3 ft (16:9)
2.7 to 3 ft (4:3)
3 to 3.6 ft (16:9)
Also keep these considerations in mind:
■ Place the projector on a sturdy, level surface.
■ Make sure there is plenty of space for ventilation around and
under the projector. Do not set the projector on top of loose
papers that could block the vents under the projector.
■ Make sure the projector is within 6 feet (2 meters) of a grounded
electrical outlet or extension cord.
Try to place the projector directly in front of the center of the screen,
facing it toward the screen squarely. If the projector isn’t positioned
this way, the image will be “keystone” shaped, instead of square or
rectangular.
If you place the projector below the level of the screen, you’ll have to
tilt it up by extending the front adjustable foot, as described on
page 39. This also causes the image to lose its rectangular shape. You
can adjust the shape using the buttons on the projector (see page 40),
or using the projector’s menu system (see page 49).
The Auto Keystone feature corrects the distortion automatically. See
page 57 for more information about Auto Keystone correction. If
necessary, you can adjust the image shape manually as described on
page 40.
Other Installations
You can also project from behind the screen or from the ceiling, with
the projector mounted upside-down:
translucent screen)
Front/ceiling projectionRear projection (using a
Rear/ceiling projection (using
a translucent screen)
To project from overhead, you’ll need the optional ceiling mount
hardware. (See page 14 for ordering information.) You’ll also need to
select
Front/Ceiling or Rear/Ceiling for the Projection option in the
Extended menu. To project from the rear, select
Rear. See page 58 for
more information.
Setting Up the Projector 17
Connecting to a Computer
note
If you have an iBook with
an RCA video-out port,
follow the instructions for
connecting to a video device
on page 25.
You can connect the projector to any computer that has a standard
VGA or BNC monitor port, including PC notebook and laptop
computers, Macintosh PowerBooks and iBooks, and hand-held
devices.
Follow the instructions in this section to:
■ Connect the projector to your computer with the VGA cable
included with the projector.
■ Connect the projector to your computer with a commercially
available VGA–5BNC cable.
After connecting the projector to your computer, you may also
want to:
■ Connect a monitor to the projector so you can view your
presentation close-up as well as on-screen (not necessary if you’re
using a laptop); see page 21.
■ Connect the projector to your computer with a commercially
available audio cable to play computer audio; see page 22.
Connecting with the VGA Cable
18 Setting Up the Projector
Follow these instructions to connect to your computer with the VGA
cable that came with your projector. Before you start, make sure your
computer and the projector are turned off.
1. If you are connecting the projector to a desktop computer,
disconnect the monitor cable from your computer.
2. Locate the VGA computer cable that came
with the projector.
VGA computer cable
Connect one end of the cable to the projector’s Computer1 or
Computer2 port.
Computer1 and Computer2 ports
3. Connect the other end of the cable to your computer’s video-out
or monitor port.
If you’re using a PowerBook or iBook and you can’t connect the
cable, you may need to use an optional Macintosh video adapter;
see your computer dealer.
4. If you connected the computer to the
Computer1 port and you
want to view the display simultaneously on your computer
monitor and the projector screen, see “Connecting an External
Monitor” on page 21.
5. To play audio from your computer through the projector
speakers, see “Playing Sound Through the Projector” on page 22.
6. Tighten the screws on the connectors.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
Source Search
button on the projector or remote control. See page 36.
Setting Up the Projector 19
VGA-5BNC cable
Connecting with a VGA-5BNC Cable
If your computer provides video output through BNC connectors,
follow these instructions to connect the projector to your computer
with an optional VGA-5BNC cable. Before you start, make sure your
computer and the projector are turned off.
1. Disconnect the monitor cable from your computer.
2. Connect the cable’s VGA connector to the projector’s
Computer1 or Computer2 port.
Computer1 and Computer2 ports
3. Connect the BNC connectors to your computer’s BNC ports.
20 Setting Up the Projector
4. If you want to view the display simultaneously on your computer
monitor and the projector screen, see “Connecting an External
Monitor” on page 21.
5. To play audio from your computer through the projector
speakers, see “Playing Sound Through the Projector” on page 22.
6. Tighten the screws on the VGA connector.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
Source Search
button on the projector or remote control. See page 36.
Connecting an External Monitor
If you want to see your presentation close-up as well as on the
projection screen, you can connect an external monitor to the
projector. This lets you view images on your computer monitor while
the projector is in standby mode (plugged in but not turned on) and
check your presentation or switch between picture sources even if
you’ve pressed the
projection on the screen.
Simultaneous display is possible only when the computer is connected
to the projector’s
Make sure the projector and computer are off. Then connect the
monitor’s cable to the projector’s
A/V Mute button on the remote control to turn off
Computer1 port.
Monitor Out port, as shown:
note
Some LCD monitors may
not be able to display the
image correctly. If you have
trouble displaying the
image, connect a multiscan
monitor. If you’re projecting
computer images, make sure
the computer’s refresh rate is
set to 65 Hz or greater.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
Setting Up the Projector 21
Playing Sound Through the Projector
You can connect a commercially available 3.5 mm stereo mini-jack
audio cable to take advantage of the projector’s built-in speaker. You
can obtain the audio cable from a computer or electronics dealer.
1. Connect one end of the 3.5 mm stereo mini-jack audio cable to
the corresponding
2. Connect the other end of the audio cable to your laptop’s
headphone jack or audio-out jack, or your desktop’s
speaker or audio-out port.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
Audio1 or Audio2 jack on the projector.
Audio1
and
Audio2
jacks
22 Setting Up the Projector
Connecting External Speakers
You can output sound to external speakers with built-in amplifiers.
When you play sound through external speakers, the projector’s
built-in speaker system is disabled.
1. Locate the appropriate cable to connect your speakers.
Depending on your speakers, you may be able to use a
commercially available audio cable with a stereo mini-jack
connector on one end and pin jacks on the other end. For some
speakers, you may have to purchase a special cable or use an
adapter.
2. Connect the stereo mini-jack end of the audio cable to the
Out
port on the projector.
Audio
3. Connect the other end of the cable to your speakers.
When you use external speakers with the projector, you can use the
or volume buttons on the projector or the
Vol- and Vol+ buttons
on the remote control to adjust the volume. First, you need to select
the maximum volume on the external speakers. Then you can use the
projector or remote control buttons for further adjustments.
Setting Up the Projector 23
note
The projector does not
support TV antenna cable
F connectors.
Connecting to Video Sources
You can connect a DVD player, VCR, camcorder, digital camera,
gaming console, or any other compatible video source to your
projector. You can connect up to four video devices at one time.
The projector supports HDTV, SDTV, NTSC, PAL, and SECAM,
and automatically detects the video format. It can receive composite
video, S-Video, RGB video, and component video. The type of cable
you need depends on the video source:
■ For composite video, use a commercially available RCA A/V
cable. See page 25.
■ For S-Video, use the S-Video cable supplied with your video
device or order one from Epson. See page 26.
■ For RGB video, use the VGA computer cable included with the
projector. See page 27.
■ For component video, you’ll need the optional Epson
component-to-VGA video cable. See page 28.
After connecting your video device to the projector, you may want to
connect an audio cable to play sound from your video equipment
through the projector’s built-in speaker or external speakers. See
page 29 for instructions.
24 Setting Up the Projector
Connecting a Composite Video Source
If you’re connecting a composite video device, use a commercially
available RCA A/V cable. Before starting, make sure the projector and
your DVD player or other video source are turned off.
1. Connect the yellow RCA plug on one end of the cable to the
projector’s yellow
2. Connect the yellow plug on the other end of the cable to the
video-out port on your video source.
3. To play sound through the projector, follow the instructions
beginning on page 29.
Video port.
Video port
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
Source Search
button on the projector or remote control. See page 36.
Setting Up the Projector 25
Connecting an S-Video Source
If your video source has an S-Video jack, you can use it to project a
higher quality video image. You’ll need an S-Video cable, which is
usually provided with your video source, or you can purchase one
from Epson (part number ELPSV01). See page 14 for ordering
information.
Before starting, make sure the projector and your DVD player or
other video source are turned off.
1. Insert one end of the S-Video cable into the projector’s
S-Video
port and the other end into the S-Video output port of your video
source.
S-Video port
2. To play sound through the projector, follow the instructions
beginning on page 29.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to the projector, select the
correct source after projection starts by pressing the
Source Search
button on the projector or remote control. See page 36.
26 Setting Up the Projector
Connecting an RGB Video Source
Follow these instructions to connect the projector to a video player or
satellite receiver that has an RGB video output port using the VGA
computer cable that came with the projector.
Before starting, make sure the projector and your DVD player or
other video source are turned off.
1. Connect one end of the VGA computer cable to the
Computer1
or Computer2 port on the projector.
Computer1 and Computer2 ports
2. Connect the other end to the video port on your player.
3. To play sound through the projector, follow the instructions
beginning on page 29.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to the projector, select
Computer 1 or Computer 2 as the source after projection starts by
pressing the
Source Search button on the projector or remote
control. See page 36.
Setting Up the Projector 27
Connecting a Component Video Source
If your video source has component video connectors, you can use
them to project a higher quality video image. You’ll need a
component-to-VGA video cable, which can be purchased from Epson
(part number ELPKC19). See page 14 for ordering information.
Before starting, make sure the projector and your DVD player or
other video device are turned off.
1. Connect the 15-pin VGA connector end of the
component-to-VGA video cable to the projector’s
Computer2 port.
Computer1 and Computer2 ports
Computer1 or
28 Setting Up the Projector
2. Insert the three component ends of the component-to-VGA video
cable into the color-coded video output ports on your video
source, usually labelled
Y, Pb, Pr or Y, Cb, Cr.
3. To play sound through the projector, follow the instructions
beginning on page 29.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
If more than one device is connected to your projector, select
Computer1 or Computer2 as the source by pressing the Source
Search
button on the projector or the remote control. See page 36.
Playing Sound Through the Projector
The projector has a built-in speaker with a maximum output of 10 W.
You can play sound from your video equipment through the
projector’s speaker if your video device has an audio output port.
For RCA-Type Audio Output Ports
Most video devices have an RCA-type audio output port. In this case,
use a commercially available RCA-type audio cable to connect the
projector to your video source:
1. Connect one end of the RCA audio cable to the
L-Audio-R jacks
on the projector.
L-Audio-R jacks
2. Connect the red and white plugs on the other end of the RCA
audio cable to the corresponding color-coded audio output port
on your video source.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
Setting Up the Projector 29
For Stereo Mini-Jack Audio Output Ports
Some video devices, especially camcorders, may have a stereo
mini-jack audio output port. To connect to the
jacks when using the
S-Video or Video port, use a commercially
L-Audio-R input
available stereo mini-jack audio adapter cable (3.5-mm stereo
miniplug to two male RCA plugs) to connect to the projector.
1. Connect one end of the audio adapter cable to the
L-Audio-R
jacks on the projector.
L-Audio-R jacks
2. Connect the other end of the audio adapter cable to your video
device’s audio output port.
If you don’t need to make any other connections, you can plug in
your projector and turn it on. See page 34 for instructions.
30 Setting Up the Projector
Loading...