Epson PowerLite 800p, PowerLite 810p Quick Start Guide

Locate everything you’ll need

For most setups, you’ll need just these two cables:

power cord computer cable

EPSON®PowerLite®600p/800p/810p

Quick Setup

You won’t need to install any software.

Connect the projector to your laptop

Make sure your projector and laptop are turned off.

Connect one end of the computer cable to the

Computer 2/Component Video port on the projector.

Follow these instructions to connect the projector to your laptop. To connect other devices, such as a VCR or desktop PC, see your User’s Guide.

Connect the other end to your laptop’s video or monitor port.

Plug in your projector

Connect the power cord to your projector and plug the other end into a grounded outlet.

Turn on your equipment

Turn on the projector first. To do so, press the red Power button.

The power light flashes green as the projector warms up, and the projection lamp comes on in about 30 seconds.

power light

power button

Turn on or restart your laptop. (Windows only: If you see a

New Hardware Wizard screen for a Plug and Play monitor, click Cancel.)

Caution: Before unplugging the projector...

Press the red Power button twice, then let the projector cool while the power light flashes orange (about a minute). Once the light stops flashing and stays on, it’s safe to unplug the projector.

Never unplug the projector when the power light is green or flashing orange.

Turn Over

Adjust the image

Remove the lens cap and rotate the focus ring

to sharpen the image.

zoom ring

focus ring

EPSON PowerLite 600p/800p/810p

Raise the image as needed. To do this, press the foot release button and lift the front of the projector. Once the image is

positioned where you want it, release the button to lock the foot in position. If you need to straighten the image, rotate the round adjustable foot at the back of the projector.

back adjustable foot

Note: If you see a blank screen after focusing,

see the box below.

Rotate the zoom ring to reduce or enlarge the image.

(You can also move the projector closer to or farther from the screen.)

If you see a blank screen

If you see a blank screen or the No Signal message after turning on your laptop, check the following:

Á Make sure the power light is green and

not flashing and the lens cover is off.

If your image looks like or , press the Sync+ or Sync–

(vertical Keystone) button to correct the shape of the image.

If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the center of the screen, facing the screen squarely. Or press the Tracking+ or Tracking– (horizontal Keystone) button to correct the shape.

If you’re using a Macintosh:

1. From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound.

2. Click the Arrange icon.

Á Try turning off the laptop and restarting it.

Á If you’ve connected more than one computer and/or video source,

you may need to press the Computer/YCbCr or Video button on top of the projector. (Allow a few seconds for the projector to sync up after pressing it.)

Á Make sure your cable is connected securely.

If you’re using a Windows laptop:

Á Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD. You may have to hold down the Fn (function) key while pressing it. (Allow a few seconds for the projector to sync up after pressing it.) Check your laptop’s manual or online help for details.

click here

drag one monitor icon on top of the other

3. Drag one monitor icon on top of the other. This lets you display on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

On most systems, the or CRT/LCD key lets you toggle between the LCD screen and the projector, or display on both at the same time.

Á You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

click here

the projector to sync up after making the selection.)

select a Simulscan resolution

CPD-12789